similar to: Dell 860

As these problems are very time sensitive and frustrating, I suggest you document each change you make and do them one at a time so you can actually know what the problem was and not introduce new problems in the process. Find someone who is on the phone quite a bit and will give you an honest evaluation of the call dropping situation (unless you yourself are experiencing this issue too).

Hello everyone, I'm considering getting me a quad-core Dell PowerEdge 860 to run Asterisk. Anyone else using this model? Any tales of woe and sorrow I should know about? Then, in a couple of weeks, I'm thinking of getting a Sangoma A108 and giving that a try. Same question with that one - any quirks I should be aware of? Girts -------------- next part -------------- An HTML

Sorry I should have stated that I've tried +x, -x, x.y and x and I still get the same. Regards Lee -----Original Message----- From: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com] On Behalf Of Eric "ManxPower" Wieling Sent: 05 January 2007 08:10 To: Asterisk Users Mailing List - Non-Commercial Discussion Subject: Re: [asterisk-users]

Hello every body, I ve installed Trixbox 1.2 on "DELL OPTIPLEX GX 240", i upgreded it to the latest version. I've 2 cards installed in the same pci channel via a bridge or plug i don't know exactly what's his name( but a card (1 pci) that gives 2 pci channels) the first card is TDM400P: it's ok the second is TE110P: it's not ok . No led is on neither the red nor the

I am running Asterisk 1.2.14 and Zaptel 1.2.12 and using a Digium TE110P card in E1 mode. I've recently noticed in my logs the following Jan 5 01:27:11 VERBOSE[22490] logger.c: [chan_zap.so]Jan 5 01:27:11 VERBOSE[22490] logger.c: [chan_zap.so] => (Zapata Telephony w/PRI) Jan 5 01:27:11 VERBOSE[22490] logger.c: == Parsing '/etc/asterisk/zapata.conf': Jan 5 01:27:11

-----Mensaje original----- De: Mario Montiel [mailto:mariomontiel@grupocsi.com.mx] Enviado el: Viernes, 26 de Mayo de 2006 10:29 p.m. Para: Asterisk Users Mailing List - Non-Commercial Discussion Asunto: RE: [Asterisk-Users] DELL PowerEdge 2850 and TE4110P and TE110P I have many problems with this server and two cards TE4110P, because after several minutes one of two cards stays out without

Hi all, as good? I try to install asterisk-1.2.14, zaptel-1.2.12,libpri-1.2.4,addons-1.2.5 , sounds-1.2.1 and wanpipe-2.3.4-3 and hwec-utils-beta4-2.3.4 But it is not compiling drivers of the Sangoma, why udev's for board in "/dev/zap"(1-31, channel,ctl,pseudo,timer) is not created. But when I install a board TE110P Digium, udev's is created and asterisk functions perfectly. : )

currently using 1.2.14 and zaptel 1.2.12 i'm using mfc/r2 so i can't move to 1.4 with sip jitter control and improved jitter control in zaptel 1.4. my problem is excessive jitter using linksys spa942. when i set canreinvite=no, which forces rtp to pass through *, quality is horrible. clicking sounds, pauses, etc. but when omitted or canreinvite=yes, sip to sip calls are ok. now, the

Before studying your configs, what have you tried so far? Did you change this? Also, try changing your second span timing from span=2,2,0,ccs,hdb3,crc4 to span=2,0,0,ccs,hdb3,crc4. Here is the documentation on voip-info for why it may be the cause of your issues http://www.voip-info.org/wiki/view/Zaptel.conf+span+syntax span definition format:

Hello All, I have got my TE110P working at the hardware level, turned out to be a dodgy cable causing the Yellow errors in zttool. However, now I am getting yellow errors in asterisk, but zttool shows nothing out of the ordinary. here is my current config, and some asterisk console errors, any suggestions most welcome. zaptel.conf span=1,1,0,ccs,hdb3 bchan=1-15 dchan=16 bchan=17-31

I have a customer that has a Dell SC1420. They want to use that as their Asterisk server w/ a Digium TE110P. Digium's website doesn't mention this server one way or the other in their compatibility list. Is there anyone out there using the SC1420? If so, any problems? Cheers, Kevin

jglucky@blueware.net wrote: > Has anyone attempted or have had any issues getting Asterisk and > Digium cards working on a Dell SC420 server? I have it up and running on 2 SC420's with TE110P cards. Haven't had any problems as of yet (knock on wood). Dell SC420 TE110P 2x40 GB SATA drive in a RAID 1 setup (Linux 2.6 kernel needed for SATA drives; turn off RAID detection in BIOS).

Hi, I am struggling to get rid of a conflict on DELL 2800 : PCI Parity error (EB113 on the display) I am learning linux and asterisk as I go along, there might be obvious things I should know, but bear with me. >From demsg below my 2 digium cards installed are listed (no config or connections done to digium cards yet), the conflict is with the TDM400P card, without that card, in any slot, no

Hi all I'm trying to get to grips with this one, but just can't figure it out. I recently acquired some 2nd hand Dell Poweredge 860 servers, and noticed that they have built in remote management interfaces. So, I have setup one, and assigned an IP address to it, but have no idea on how to access it remotely. Google'ing for an answer didn't bring me more than general product

Hi I'm looking for some help with Vicidial, If you have experience with it and could help with some consulting please contact me off list. Cheers, Joel Hill Asterisk IT jhill@asteriskit.com.au

Hi list, I have a terrible noise issue with Dell SC1430 + Digium TE110P. The digium card is not sharing interrupts with any other device, as I saw in Dell's BIOS and also with "lspci -vb" command. After changing coax wire, UTP, balum, digium card ... I have found that the problem is in Dell box, so now I'm running the same Asterisk config in other server with the same

Hi All Before I go out and buy a DELL PowerEdge 2850 has anyone had problems (or any other useful experience) getting a TE411P to work with it. I also have a legacy TE110P. Has anyone had problems with this combo. -- Dr. Rodney G. McDuff |Ex ignorantia ad sapientiam Manager, Strategic Technologies Group| Ex luce ad tenebras Information Technology Services | The

Hi steve and All, I'm attaching cat proc/interrupts out put, lspci -bv out put, zapa.conf, zaptel.conf for your information Thanks so much for the feedback and I do accordingly. Hope to get rid off this isue any how. To day also reported 10 call drops within 2 hours of period. fook forward to have your support on this regard. Thanks & Regards, Vidura Senadeera, Network Engineer,

Hi All, First off, I've just started using compiz and its fantastic... I'm using compiz with KDE (on FC6), all is OK apart from one small niggle which is when I use the scale or switcher plugins it includes my kicker windows (the desktop panels) in the list, which isn't so pretty. I don't know much about gconf, but poking around in the settings for compiz and found that these

I have an Asterisk box running Fedora Core 4, Asterisk 1.4, Lippri, 1.4, and Zaptel 1.4 The Digium cards installed are TDM2400 and TE110P. Everything was working fine until I upgraded to zaptel 1.2.12 from 1.2.9 Now when I run ztcfg I get the following error message: (CAS signalling on span 2 conflicts with Clear channel on channel 40) --NOTE: signaling was spelled wrong in the error