similar to: S400M (FXS) Modules no longer seen

I have a TDM21B (A new TDM20B that just arrived plus a X100M that I already had). This card sometimes works, and sometimes only the FXO module is seen. (correction to previous message that incorrectly listed X400M/S400M when I'm using only the single port versions of these modules (X100M/S110M). By "works", I mean all 3 modules have the green lights on the ports on and when

I'm having problems with a TDM22B. The FXO modules work fine. Both FXS modules fail to initialized. The error messages I see when the module loads: Init Indirect Registers UNSUCCESSFULLY. Indirect Registers failed verification. I already RMA'ed a TDM22B because of this problem. Now that the replacement shows a similar issue, I want to see if anyone else can think of something to

I apparently have a dead FXS module. Is there any kind of test I can run on it (on a live system) to determine if its good or bad? The telephone has no dialtone, gets no calls. It has been working for several months, and just quit yesterday. Thanks! Found a Wildcard TDM: Wildcard TDM400P REV I (4 modules) Freshmaker version: 73 Freshmaker passed register test Module 0: Installed -- AUTO

I have a TDM400P with one FXO module and two FXS modules in it. I also have a Wildcard X101P. After trying hard to get things working on various Intel computers, but having echo problems that made it not really usable, I decided to try it on some older PowerPC (Macintosh) hardware running Yellow Dog Linux. Things started off smoothly. Both zaptel and asterisk seemed to compile okay, and both

Greetings all, I'm new to asterisk... Finally got two IP phones and two TDM400P's (one with four FXO modules and one with four FXS modules)... Began experimenting a couple days ago and have ran into a very aggrevating problem. My system consists of the following hardware: Abit BL7-RAID motherboard Pentium 4 1.6GHz processor 512MB SDRAM 2 TDM400P cards 2 3Com 3c905

The REV I card shows up in the PCI table as: 02:05.0 Network controller: Tiger Jet Network Inc. Intel 537 (or 02:05.0 Class 0280: e159:0001) Subsystem: Unknown device b119:0001 But the REV E/F shows up as: 02:0d.0 Communication controller: Tiger Jet Network Inc. Tiger3XX Modem/ISDN interface (or 02:0d.0 Class 0780: e159:0001) Subsystem: Unknown device b100:0003 One

Hi all, Yesterday, in an attempt to take back my phone room, I pulled everything apart as far back as the demarc and rebuilt it. In the process of putting things back together I accidentally connected my incoming lines to my FXS ports and my phones to my FXO ports. I quickly realized the mistake I made and corrected things but not before one of my FXS modules was smoked by incoming ring voltage.

I just installed an FXS module onto a 4 channel tdm thats about 5 years old and it wont work. Running dmesg I can see the following error: Zapata Telephony Interface Registered on major 196 Freshmaker version: 71 Freshmaker passed register test !!!!!!! LOOP_CLOSE_TRES iREG 1C = 1 should be 1000 !!!!!!! RING_TRIP_TRES iREG 1D = 8000 should be 3600 !!!!!!! COMMON_MIN_TRES iREG 1E = 0 should

Hi , I have an asterix (1.2.7.1) box with 3 TDM400P and 10 FXO modules, and zaptel (1.2.5). The problem is that 6 modules can't be initaized and i get the folowing error: May 7 09:17:37 WARNING[7739] chan_zap.c: Unable to specify channel 9: No such device May 7 09:17:37 ERROR[7739] chan_zap.c: Unable to open channel 9: No such device here = 0, tmp->channel = 9, channel = 9 ztcfg output

No matter what I do, I've tried now three different motherboards, my TDM400P keeps giving 'Freshmaker failed register test' after emitting a list of xx != 00 errors. Anyone have any clues for me? I'm wondering if I got a bad module or what. TIA -- Undocumented Features quote of the moment... "It's not the one bullet with your name on it that you have to worry about;

Hi all, I am going to have a TDM20B FXS card and sit in it in my Asterisk box, I need out going calls only. I am quite a newbei of it, I hope your tips and tricks with valuable links. Thank you Kumara

Hi, I recently installed a gentoo on a PC, purchased a TDM400 and installed asterisk. Kernel is 2.6.11-rc3 First, there seems to be a problem with my system: I must put the pci=routeirq to make the card detected. The modules are loaded ok (dmesg output) Zapata Telephony Interface Registered on major 196 ACPI: PCI interrupt 0000:00:08.0[A] -> GSI 16 (level, low) -> IRQ 16 Freshmaker

I got this nice TDM22B with two green modules left and two modules right /var/log/messages shows: Nov 26 23:47:48 dns kernel: Zapata Telephony Interface Registered on major 196 Nov 27 00:37:53 dns kernel: Freshmaker version: 71 Nov 27 00:37:56 dns kernel: Freshmaker passed register test Nov 27 00:37:56 dns kernel: Module 0: Installed -- AUTO FXS/DPO Nov 27 00:37:56 dns kernel: Module 1: Installed

I got this nice TDM22B with two green modules left and two modules right /var/log/messages shows: Nov 26 23:47:48 dns kernel: Zapata Telephony Interface Registered on major 196 Nov 27 00:37:53 dns kernel: Freshmaker version: 71 Nov 27 00:37:56 dns kernel: Freshmaker passed register test Nov 27 00:37:56 dns kernel: Module 0: Installed -- AUTO FXS/DPO Nov 27 00:37:56 dns kernel: Module 1:

Hi all, I'm trying to install a TDM400P card, and I need some help. Please, see below... after dmesg command: [root@voip root]# dmesg via82cxxx: board #1 at 0xD800, IRQ 5 Zapata Telephony Interface Registered on major 196 PCI: Found IRQ 3 for device 00:09.0 PCI: Sharing IRQ 3 with 00:10.1 Freshmaker version: 71 Freshmaker passed register test Module 0: Installed -- AUTO FXS/DPO Module 1:

Hi all, I'm trying to install a TDM400P card, and I need some help. Please, see below... after dmesg command: [root@voip root]# dmesg via82cxxx: board #1 at 0xD800, IRQ 5 Zapata Telephony Interface Registered on major 196 PCI: Found IRQ 3 for device 00:09.0 PCI: Sharing IRQ 3 with 00:10.1 Freshmaker version: 71 Freshmaker passed register test Module 0: Installed -- AUTO FXS/DPO Module 1:

Hi all, Does somebody know why no load modules to FXS? I used zaptel-1.0.7 version driver. [root@server1 zaptel-1.0.7]# modprobe wctdm ZT_CHANCONFIG failed on channel 3: Invalid argument (22) Did you forget that FXS interfaces are configured with FXO signalling and that FXO interfaces use FXS signalling? /lib/modules/2.4.21-27.EL/misc/wcfxs.o: post-install wcfxs failed

I have a small system based on one TDM400 card with - 2 FXO modules for incoming lines - 1 FXS module for one phone The system was working fine in the past. The motherboard was exchanged and during the switch, the phones line was rewired with a mistake and a incoming phone line was connected to the FXS module, and there was ringing voltage on the module. Now, the system kinda works but the FXS

Can someone please help me with my config settings for my TDM12B. I have got the FXS port to work fine, but I cannot get asterisk to startup with any settings for the fxo ports. It appears to be something related to the message "Signalling requested is FXS Kewlstart but line is in FXO Kewlstart signalling". However, I have tried what appears to be every possible configuration option. I

Hi all, I was wondering if anyone had any pointers on how to determine whether or not a module has gone wonky on the TDM400P? I have a 2 FXO (channels 3 and 4) and 2 FXS unit (channels 1 and 2). The bad (?) module in question is the FXO module on channel 3. I can't dial in to or out of that channel; dialing in gives a busy signal, dialing out just shows * hanging around after attempting a