similar to: TE110P with Qsig

Hi, For a significant time now (since about 0.2.0-rc8n) the qozap driver has become very verbose if an ISDN line is not connected... I get the messages below every couple of seconds in the asterisk logs. The "flaw" in the messages is the "Alarm cleared" message - The alarm cannot possibly be cleared because there is no physical media connected into that port!!! (BTW - All

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hi. I'm getting the following error at random intervals on my TE410P with Asterisk CVS-03/30/04-11:49:01-CEST. I have two spans active, one connected to my Telco, the other to a Siemens PABX. Both spans display this behavior at random intervals. All calls are dropped when this happens. Spans are not necessarily in use when this happens.

Hello all, I got a problem at an asterisk server, with dropping calls, losing all channels and reaktivating all channels and beeing back up. This problem seems to occure randomly over the whole day, when it gots traffic on the card. After looking @ google I found several hints but none did work fine. To avoid problems with the phone line (german E1) I called the provider, he did a 45 min. route

Hey, I wrote yesterday about PRI dropping, which turned out to just be a regular reset of unused B-channels. This time there's a real issue. As noted earlier I have an ISDN-30 connection, a Digium TE-121 with VPMADT032 echo cancellation. These are my configurations files: == /etc/zaptel.conf loadzone=dk defaultzone=dk span=1,1,0,css,hdb3,crc4 bchan=1-15 dchan=16 bchan=17-31 == ==

I am trying to connect two machines to each other with an T1 crossover cable. The first machine has two TE120P cards - one connecting to the telco on an ISDN PRI. The second to a crossover T1 cable to a second machine which has one TE120P card. Telco <-cA-> Machine1 <-cB-> Machine2 Machine1: Two TE120P cards Machine2: One TE120P card cA: Standard T1 Cable cB: Crossover T1

Hi everyone, I have a PRI conection on an * system running Asterisk 1.0.9, libpri 1.0.9 and zaptel 1.0.9.2 connected to an AXE 10 (APZ 21220 System 64) in the network side. I know the system and the wildcard I´m using are ok because I´ve used them before with other PRI connections (to a Siemens EWSD) without any problem. First the PRI didn´t work (I got the TE110P alarmed with red). After

Hi guys, I've been trying to get my ISDN-10 line up for the past few days, but its been going up and down. I am using OpenVox D110P card on asterisk version 1.4.21. It seems to me like a cable problem. I tried using Ethernet straight cable (12, 45, 36, 78) and also a "straight" cable where the twisted pairs are on 12, 34, 56 and 78. The problem remains the same.

Hi fellow asterisk users, I am running Asterisk 1.4.29 with an Digium TE121 card (wcte12xp kernel module) an approx. 100 snom320. The whole installation is running without issues since 5 months. Without having changed anything on the asterisk server for at least 2 months, i noticed "clicking sounds" at external calls over the PRI. Asterisk constantly throws the following messages: ...

Hi, I hope someone can help me with this.... Asterisk 1.0.6 Zaptel 1.0.6 Libpri 1.0.6, 1 Digium E100P card installed Panasonic TDA200 firmware v2.0.6 E1 Card Firmware 1.0.2 System is located in Australia, so as technologies go, I believe it is twist on the euro standard for the E1 signalling. Here is the situation. The TDA E1 card is set in cross over mode and I am using a functional

I receive this error on the asterisk console and it is pretty much ALWAYS coming up. Sometimes there will be a break where it does not display. We had our PRI provider test the lines and they claim that there is no signalling problem. It doesn't matter if there are no calls or if there are 10 calls in progress the error is still displayed. I also get an annoying popping or clicking sound

Hi!, this issue makes me crazy. I read a lot of docs, also * mailling list and I try a lot of things without success. Any help will be appreciated. Here is the info: Hardware: -------------------------------------------- Supermicro Server with motherboard X7DB8, chipset Intel 5000P, Xeon 5050 Digium TE110P Software --------------------------------------------- Asterisk version 1.2.12.1

I am trying to test out my PRI configuration on a server by conection another asterisk server to it. I have the T-1 cards up and both set to bchan=1-23 and dchan=24 in zaptel.conf I am getting lost on the signalling in zapata.conf. using pri_cpe makes sense for my target box, but I am getting the following errors on my source box if I use pri_net or pri_cpe signalling. May 31 17:15:06

Greetings to all, I am getting the following error on my PRI-connected Asterisk box, and am just wondering if anyone else has seen this, and if so how they solved it. Jan 18 10:10:23 NOTICE[6070]: chan_zap.c:7428 pri_dchannel: PRI got event: HDLC Bad FCS (8) on Primary D-channel of span 1 Jan 18 10:10:24 NOTICE[6070]: chan_zap.c:7428 pri_dchannel: PRI got event: HDLC Bad FCS (8) on Primary

Hi all, After running fine for a few months now asterisk seems to hang frequently , still functioning but the DAHDI channels seem busy (users report a busy signal when calling or being called) A reboot will allow it to run for another day or maybe 2 or 3 till the problem occurs again. running stock Asterisk 1.6.2.9-2+squeeze2 on Debian with stock kernel 2.6.32-5-686 i get the following

"RED: Loss of signal (LOS): The equipment shall assume "loss of signal" when the incoming signal amplitude is, for a time duration of at least 1 ms, more than 20 dB below the nominal amplitude. The equipment shall react within 12 ms by issuing AIS." This sounds like what is happening, and is in order with what one of the technicians said - I was about 20 dB below their

"RED: Loss of signal (LOS): The equipment shall assume "loss of signal" when the incoming signal amplitude is, for a time duration of at least 1 ms, more than 20 dB below the nominal amplitude. The equipment shall react within 12 ms by issuing AIS." This sounds like what is happening, and is in order with what one of the technicians said - I was about 20 dB below their

Hi all, Last night I went to replace an Asterisk 1.4 + mISDN + b410p box with Asterisk 1.6.2 and DAHDI BRI - to no avail. I had two servers so copied network setting etc from the working one, moved the card across, ran dahdi_genconf etc and it didn't work. Here's the console output with notices disabled: lucas*CLI> pri intense debug span 1 Enabled debugging on span 1 [Dec 16

Hi, I am getting this message on the * console on my first pri span. Pri show span show it is down, and I can't make any calls from the span. Apr 27 07:40:23 NOTICE[23988]: chan_zap.c:8202 pri_dchannel: PRI got event: HDLC Abort (6) on Primary D-channel of span 1 Apr 27 07:40:23 NOTICE[23988]: chan_zap.c:8202 pri_dchannel: PRI got event: HDLC Abort (6) on Primary D-channel of span 1 Apr 27

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Good day eveyone, I'm hoping that someone can help me. Perhapps i'm overlooking the obvious, in truth, I hope that I am. I've scoured the mailing list and google, and haven't come up with much. I have a Digium T400P thats been connected to a channel bank for testing for some time now. all has been well. I've now just had

I have searched for how to locate echo cancelation on SIP clients, but cant find anything and echocancel=y doesnt seem to have any effect. Configuration: CVS-HEAD from last month iPAQ h5500 with SJPhone (gsm/ulaw/alaw) Problem description: When I place or receive a call I hear a faint delayed echo of myself. The other party hears a really bad nonmuted echo that makes the call unusable. Aside