similar to: DTMF Tone Issues

Ok sorry for not being specific. I am having a problem when people outside call in to my number which terminates at VoicePluse then The send IAX to me and I do not get any tones. People press buttons but it just goes to the next dialplan fall through. It happens 60-70% of the time. extentions.conf [general] static=yes writeprotect=no autofallthrough=yes clearglobalvars=no priorityjumping=no

We currently have an Asterisk system with a PRI and 6 POTs lines for backup. We are looking to add service such as Voicepulse Connect as an extra level of redundancy and a cost saving alternative to PRI calls. VP Connect only allows 4 simultaneous calls; we are looking for 4 to 5 times that to support our call center. Also, in looking through the archives, it seems like VP has had their share of

Hey all, I am dialing a DID through VoicePulse Connect. The number is answered by a main menu type of IVR. The configuration is as specified in both the wiki and VoicePulses documentation. The call comes through without a problem, but when the caller enter any keys they are either not recieved by * or they are ignored. With SIP I would typically put a dtmfmode= line under the peer and

I have working SIP numbers with broadvoice, and just added a DID from http://connect.voicepulse.com/ . The calls answer, but DTMF is not recognized. With "iax2 debug" active pressing DTMF does nothing. Zilch. Zero. A friend tried a different IAX2 connection, and got the same results. I see the following in the archives: On Fri, 2004-04-09 at 10:12, Robert Jackson wrote: > Hey

Does anyone know what happens if you try to have 5 concurrent outgoing channels with VoicePulse Connect? Does it give you an error message or a reorder or something? I'm worried about using them as my primary carrier if this is the case. I noticed that they supposedly only allow 4 channels for free and then you have to pay $20 a month extra per channel. I'm guessing this is for inbound

I have tried beta2, beta3 and now back to 1.2.12.1 and I have correct DTMF tones 25% of the time. I have to call several times to enter an extension. I have a router and a packet shaper and some other stuff. Anyone have any other ideas why this might happen. I do not have any Zap channels but I am running CentOS4. I also do not have any cards installed. Thanks

Colleagues, We're in the process of standardizing on Sprint PCS and Cingular phones on a national basis (~ 50 properties, 1000's of lines). I manage an Asterisk install at one location. I've been looking at the Multitech CellFinder CDMA for Sprint as a dial backup solution. Basically, it's a CDMA to POTS gateway, tied to a PCS account. We would see it as a trunk line and I

Is there anyone out there who has VoicePulse Connect working with DTMF? I've been unable to get it to work from the start, and the recent VoicePulse updates did not help. A caller to my DID's hears Asterisk, but pressing DTMF does nothing: On call setup "iax2 debug" shows: ----------------- Tx-Frame Retry[-01] -- OSeqno: 001 ISeqno: 002 Type: IAX Subclass: ACK

Hello: I need to be able to reliably send out touchtone to any calling party who comes into my pbx. The standard things to help with this have been done as far as I know: 1. dtmfmode is rfc2833. 2. The phones themselves are set to rfc2833. 3. allow=ulaw 4. On internal calls between extensions, touchtone works fine. Also, I have reviewed sip.conf with my carriers. Now for the

We are developing an IVR application and when I am testing locally on my machine using a softphone (iaxcomm) the digits I press for GET DATA work every time. I am testing with a local extension that goes right into my routine. However when I try to call in to the system using an analog or cell phone GET DATA drops some digits that are pressed. There doesn't seem to be a pattern to which

Hello all, I am using voicepulse DID's to receive calls via IAX to and asterisk IVR dial plan I have put together. The problem is after 3-5mins the system cant pickup the DTMF tones I am sending... I have tried different telephones... It just repeats menu options over and over.... I have to call back and then it works again for another few mins... Any ideas... iax.conf? issue? Thanks, J.C.

I run an automated information retrieval system, using Asterisk. Fairly often the system misses a dialed digit. Our codes are all 4 digits, see lots of logs with: 4199 - OK 530 - Invalid code 330 - Invalid code 5330 - OK As callers experience skipped codes. We're using Broadvoice SIP with inband DTMF (and we've tried every possible setting or option

I can't seem to dial out with Voicepulse Open Access service using *. Incoming works fine. Another user posted a few weeks back that they were having problems and there are some threads at dslreports.com about this as well. Maybe someone here can figure out what the issue is from the sip debug info below. I am at a loss. The audible error message from Allison is 0984 (from VP server) Here is

http://gizmodo.com/gadgets/cellphones/sprintsamsung-instant-cell+to+wi+fi-box-is-official-named-airave-300451.php The above is quite interesting, it would be interesting to see if it uses sip, which I have no reason to believe otherwise, and if it does, can it be hacked to talk to Asteirsk? In which case one could have a very good extension to asterisk using any Sprint Cell phone, or maybe even

Until recently, I was using Broadvoice for my in/out calling thru Asterisk. I was extremely pleased to see that Broadvoice was actually passing the callerid info (number and text) that I had set up on each device in my SIP.CONF file. I had PSTN users tell me that they were actually seeing name and extension info when I called them from the Asterisk box. Last week, due to numerous user quality

I recently switched from BroadVoice to VoicePulse Connect on my Asterisk box. Too many Meetme quality complaints (whether real or perceived). I had to make a choice to use IAX2 or SIP with VoicePulse. I first tried to go with SIP because I already had it working and all of our devices are SIP. Problem is that every time I turn my back, the Asterisk registration with the VoicePulse SIP server

Hello: I am new to the list. I am trying to set up asterisk with voicepulse. I have a voicepulse username + password, and SIP DID. When I login to voicepulse, I have this under my devices tab: Devices *Login:* Sysxxxxxxx *Password:* xxxxxxxxxx *Context:* VPWS *Connects to:* gw5.voicepulse.com My question is: Do I need a 2.4.x kernel? Currently I am running Debian/stable stock 2.2.x ? Has

I'm trying to use Jeremy's suggestion of dialling using just the peer name instead of user:pass@peer but I'm running into some really funky issues. It does the same thing with both VoicePulse and another * server I have. [voicepulse] type=peer host=gw5.voicepulse.com trunk=yes user=USERNAME pass=PASSWORD and in my dialplan: Dial(IAX2/voicepulse/${EXTEN:2}@VPWS,90,r) The log shows

Hey guys, Im about to sign up for VoicePulse Connect. Of course, I plan on using my asterisk server to "register =>" with the service. I would rather sign up with VoicePulse via SIP instead of VoicePulse Connect. My asterisk box is behind another Linux box serving as my nat/firewall. Does anybody think I will have a problem ? Should I stick to IAX and VoicePulse Connect or can I use

We're beginning to test MultiTech's CallFinder CDMA Units, one for Sprint PCS and one for Alltel. They sell both. Our intent is to use them as a backup line for our main office (which has a PRI) and a backup/911 line for our remote offices which are all connected via * over a VPN with no local trunks at any of them. In the interest of maximizing use of the lines, I'm putting