similar to: Conference between skinny user and many sip user

Displaying 20 results from an estimated 10000 matches similar to: "Conference between skinny user and many sip user"

2006 Dec 04
1
forward skinny call to SIP
Hi i have to do the following setup: 1 - i receive a call on skinny protocol 2 - i forward the call to a sip user I think that the skinny phone must be registered on asterisk, in a particular extension, for example: [skinny_internat_ext] 987,1,Dial(SIP/user@host) And if the skinny phone dials 987 i make the call to SIP/user. But how can i do that if the skinny phone isn't registered to
2006 Oct 30
3
Cisco 7960 Skinny calling SIP phone
Before I got down the path of converting a Cisco 7960 I have over to SIP I wanted to try and set it up using Skinny. The phone registers ok with Asterisk. When I call a SIP softphone extension on my network the call is made and I can answering it. However no voice is heard over the call. When I debug Skinny on the console after the call has connected I see the following messag: Recieved Alarm
2003 Oct 14
1
Cisco hard IP phones and Skinny vs. SIP
I have Asterisk up and running and it is working great with my SIP phones. However, I have some "Skinny"-protocol Cisco 7960s. Does Asterisk support the Skinny protocol? I've seen some references to Skinny in the software. If so, should I stick with Skinny with the 7960 or convert to SIP? If anyone has some Skinny confs they would send me I'd be much obliged. If I should
2003 Oct 15
2
skinny problem
has anyone seen this? -- Starting Skinny session from 192.168.13.102 -- Starting Skinny session from 192.168.13.102 triton*CLI> Oct 15 13:44:05 WARNING[213019]: File chan_skinny.c, Line 2243 (get_input): Skinny Client sent less data than expected. Oct 15 13:44:05 NOTICE[213019]: File chan_skinny.c, Line 2301 (skinny_session): Skinny Session returned: Success Oct 15 13:44:05
2004 Jan 13
4
Again: 7920 Cisco IP Phone Skinny & SIP
hi! i had some good news regarding the cisco 7920 and the internetworking with asterisk (and possibly SIP ?). Status: chan_sccp.so not coredumping anymore :-) Phone contantly in reboot loop [see below] :-( Reboot Loop means: ------------------ Phone auth's with AP Phone gets IP from DHCP & TFTP Server Phone loads OS7920.TXT Phone loads SEP<macaddr>.CNF.XML Phone loads
2003 Dec 23
1
OT: SIP vs. Skinny protocol
I assume there are several people on this list that have Cisco Call Manager implementations under their belt.... We are beginning a call manager implementation and the first question I asked Cisco was, should we use SIP or Skinny. Cisco is pushing me towards Skinny, saying that I will lose some functionality with SIP. They also say that most of their customers implement skinny. I see two
2003 Nov 01
2
Making a Skinny phone talk to Asterisk
I have a few 7960 Skinny phones. I've edited the skinny.conf file, but I'm a little unsure as to how get the phone to figure out which ip address it should register with when it boots. How do I do that? I already have a tftp server for my SIP based phones. Do I need a tftp server for skinny configs at all? And if so, can it be the same tftp server as the SIP ones use (I'm not sure
2004 Jan 14
1
Skinny behind NAT?
Can skinny work behind NAT? I have a Cisco 7910 using SCCP behind NAT that has one way audio. The called party cannot hear the calling party who's using the 7910. skinny.conf ; ; Skinny Configuration for Asterisk ; [general] port = 2000 ; Port to bind to, default tcp/2000 bindaddr = 0.0.0.0 ; Address to bind to dateFormat = M-D-Y ; M,D,Y in any order (5 chars max)
2004 Aug 05
1
Skinny and CISCO 7905G
Hello, I tried to configure a cisco 7905 IP phone using the skinny channel but I had not much luck. The relevant portion of skinny.conf is: [cisco1] device=SEP000F3487F8E3 callerid="Alex" <123-456-789> mailbox=500 callwaiting=1 transfer=1 context=default threewaycalling=1 line => 500 ; Dial(Skinny/500@cisco1) I set up the tftp server, and prepared the following
2008 Oct 09
1
Cisco 7960 sccp, Skinny and 1.4
Hi All, I'm thinking of creating a new asterisk server using the latest 1.4 stable release to replace my ageing Asterisk SVN-branch-1.2-r7231 (its been a while!). My only concern - my phones are Cisco 7960's (with sccp firmware 7.2 loaded) and to support them better, I remember compiling in a skinny(?) driver to replace the (from what I could tell) basic in built sccp support. After
2004 Apr 26
3
Skinny protocol documentation
Is there a place where I can find documentation on the Skinny protocol in Asterisk? I did a search, but I cannot seem to find much... I'm looking for information on how to get a Cisco 7960 with the CM image on it to work with asterisk.. Is it support for Skinny in asterisk even mature enough to be able to do this? Thanks, - Andre
2003 Sep 21
2
Skinny
At the present time you have to have a VALID ip address in bindaddr for Skinny to work. If bindaddr is either 0.0.0.0 or simply commented out all packets requiring the IP address contain 127.0.0.1. I forgot their nick, but someone in IRC recommended we make Asterisk be smart enough not to pick that interface, but I'm not sure of that is the problem or not. I simply have not had the
2004 Aug 23
3
Cisco 7960G, Skinny.conf, and reboots
I could use some skinny/Cisco help here. Was finally able to get the phone registered to * but whenever someone tries to call that phone it freezes and reboots itself. Same thing happens when you pick the handset up off the 7960G; it locks and reboots about 5 sec later. Here is what * shows when I plug the phone in: -- Starting Skinny session from 64.72.107.1 Device SEP000F3442E4A7 is
2005 Mar 02
0
Asterisk SKINNY with Cisco IP Conference 7935
Hi, I have one Cisco IP Conference 7935. I'm trying to config the SKINNY Protocol. I config the skinny.conf file same like sample for Cisco 7910. When somebody call me my phone ring and answer the call but I can't hear anything, But the other people is hearing me very good. When I try to call somebody the * show me an error : RECEIVED UNKNOWN
2010 Sep 27
2
SCCP (skinny) phone behind NAT: RTP dest addr wrong
Greetings: I have a working configuration for SCCP on our LANS which doesn't route RTP correctly to a skinny phone behind NAT registering from a remote public IP. Configuration: asterisk 1.4.35 servicing only skinny phones trunked to asterisk 1.2.40 which services chan_phone FXS, zap FXO and SIP phones; both instances of asterisk are behind NAT and run on the same host (using different base
2011 Jun 25
1
Cisco IP Phones and Skinny in asterisk 1.8.4.2 "tooooooooooooooooo"
Hi All; Again, the Cisco IP Phones 7942G and using Skinny: I upgraded the firmware to version 8.5 (skinny) and I am using skinny channel (chan_skinny) and the skinny.conf file. The phones are registering, but when we use them to place a call, we only hear tooooooooooo in the handset and we do not hear voice (even when we dial the digits, we only hear toooooooo .. but it dials and destination
2003 Sep 13
4
[Release] Skinny Support in cvs
If you have been paying attention, you already know this, but this weekend I have spent time ironing out the various details with my chan_skinny code that has been out there, if you knew where to look. I believe I now have all basic features operational and am going to be working on getting the class 5 (hold, transfers, call waiting and caller*id, etc) operational in the comming week(s).
2004 Sep 24
1
help with skinny
Hi all, I bought a couple phones for really cheap just for a simple solution. I'm trying to get a few 7910 to work with *. I'm just not sure how to get them to work. The 7910 just sits there "configuring IP" Here is a copy of my skinny.conf. the extensions.conf is default. I just want to bring the system up in default before a start making changes. Do I need to make
2004 Jan 29
1
IP Blue Skinny Client with Asterisk
Has anyone successfully implement IP Blue's skinny 7960 soft client with Asterisk. There is not much info that we have been able to find about configuring Skinny clients. Thanks Sam Zener
2004 Apr 08
2
i'm looking for reference guide for Skinny SCCP
Hi all, I'm writing my graduation theses : analysis VO-IP protocols , and I cannot find any documents about Cisko Skinny Client Control Protocol. I have Cisco CallManager and some IP-phone and I'm sniffing traffic between that, but I don't understand, how this protocol works. Clearly i'm looking for description of SCCP commands and explanation some basic SCCP scenarios or what