similar to: Error in codec string '=audio 5004 RTP/SAVP 3'

Hi I have a server with the last version of asterisk branches, zaptel branches, 2 Digium Card with TDM800P 16 HPEC channels (Echo Cancelation), 40 Grandstream BT200 and 10 Grandstream GXP2000. zapata.conf echocancel=64 rxgain=0 txgain=0 when i place a call o receive a call, I finish a sentence i hear a ssssssss, AND when the both side talks at the same time i have choppy audio. Any

Hello. I have a strange problem. Its not possible to pickup a call that was placed with a Siemens SL75 Wlan. When this phone calls an internal number and i try to pickup (*8) the call from my phone i get nothing. It seems i have the call for one second or so but after that the call is being cancelled. No problems with other phones (polycom, grandstream). Attached the complete sip debug log

Hi All Sorry to be a bother again but seems like I just cant get away from the problems. This time my problem is that *sometimes* a user cant transfer a call from one extension to another, I have narrowed down the problem to it only happening to calls from outside the internal system. The wierd thing about the problem is that it comes and goes one moment the user can transfer, and the next

I have just upgraded my Polycom 501's from 1.6.2.0041 to 2.1.0.2708 to get the microbrowser. Almost everything is fine except when receiving calls from a BT200 (1.1.14 and earlier) the Polycom rings but when answered, drops out and the BT200 gets a busy tone. I have many PAP2T's and SPA3000's etc and they all cal call the Polycom without problem. Does anyone know what could be going

These is my scenario. Asterisk 1.4.16 Zaptel 1.4.8 Grandstream BT200 Grandstream GXP2020 Grandstream GXP2000 For some reason the end user ask to configurate son direct access like *01,*02,*03 thru *78. After they began to use these direct access, I cant place a 3 way CONFERENCE. I remove the direct access, but i dont know if one of them block the CONFERNCE. Do you know if i can make

Hi All, I have Asterisk 11 talking to Avaya over SIP trunk using TLS and SRTP. On incoming calls from Avaya asterisk complains of 'unsupported crypto parameters: UNENCRYPTED_SRTCP' and rejects the call with '488 Not acceptable here' Doesn't Asterisk support UNENCRYPTED_SRTCP as crypto parameters in sdp? FYI SDP looks like this. v=0 o=- 1429194215 1 IN IP4 XX.XX.XX.XX s=-

Hello, is there anywhere an overview of SIP error codes and under which condition they are reported by Asterisk? There are general definitions for SIP error codes, but they are quite general and it's Asterisk that actually checks what's wrong and then reports an error. Now, currently I could check the source code to get more informations what could have caused the error, but that's

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hi all! I'm testing with a Grandstream BT200 telephone and, according to I read, it has a LED that blinks if for that extension messages were left. In "Voice Mail UserID", under the "ACCOUNT" tab, I put *100 that is the extension in which my Asterisk answer the voicemail service and if then I press MESSAGE button, the

If anyone can help im trying to get my jabra bt200 or bt250 headset working with chan_bluetooth. They seem to pair ok but they will not come out of "Negotiating" state. I get this on first start of *: [HS] jabra > AT^SPTT=? [HS] jabra < ERROR If anyone can be of help please advise, im pulling my hair out on this one. Thanks Jason Price NOTES: JABRA BT200/250

Hi All, I have working asterisk version 1.4.24. I have a blind transfer issue with grandstream bt200. I have updated the latest firmware to the phone. The phone is sending the *refer* to asterisk but asterisk is not able to connect with the another call that i have checked in sip debug. I am using transfer button of the grandstream phone. Can anybody provide help for this issue? Thanks in

Hello, Can anyone recommend a particular online WebRTC phone for testing with Asterisk? We tried: - JsSIP, but even with the "enable video" checkbox disabled it sends video options in the INVITE SDP and Asterisk rejects it with "Rejecting secure video stream without encryption details". - sipML5, but it won't register, perhaps something to do with not using the Asterisk

Hi, I have set up an asterisk with TLS and SRTP support. The SRTP is working with Phonerlite softphone. I have problem with the SRTP, when I make calls on Audiocodes gateway . I got the folloowing messages on asterisk: [Oct 2 10:59:48] NOTICE[24868]: sdp_crypto.c:232 sdp_crypto_process: Crypto life time unsupported: crypto:1 AES_CM_128_HMAC_SHA1_80

Hello all, I am having an issue with a BT-101 and * . When dialing a number from the BT-101, upon the remote side answering, the call is established but no audio is passed in either direction. I have tcpdump'd this session and found this: (192.168.30.1 is * - 192.168.30.32 is BT-101) 22:41:47.899462 IP 192.168.30.32 > 192.168.30.1: icmp 36: 192.168.30.32 udp port 5004 unreachable

Hi, I am running asterisk 1.8.5.0 and have compiled in the srtp module All but Snom phones are working. I have set the srtp tag on the snoms to 80 and RTP/SAVP to mandatory and they worked for a few hours. This morning all snoms are reporting this when trying to make a call (this is snom calling snom). ---------snip------------------ == Using SIP RTP CoS mark 5 -- Executing [10000 at

Hello list, I upgraded from Samba3.0.1 to Samba3.0.2rc1 and got now following problems: LaserJet printers 6MP (sorry, we have no other LaserJet printermodels) now couse the application to crash. With Samba3.0.1 there was no probem with that kind of Printers. I use the RPM's from ftp.sernet.de for SLES8. Printingsystem is CUPS, with raw printing and serverbased printerdrivers. Has anyone

Hi, I met a probem recently and need your help. I would really appreciate it. I kept receiving the following error message when running a program: 'Error in svd(X) : infinite or missing values in x'. However, I did not use any svd function in this program though I did include the function pseudoinverse. Is the problem caused by doing pseudoinverse? Best regards, Tongtong

Stuck with TLS transport, I have 2 phones (both in local network for tests) one connected with up second with tls when I calling TLS to UPD everything is fine, but when UDP calls TLS I getting an error ERROR[44230]: pjsip:0 <?>: tlsc0x7f143012 TLS connect() error: Connection refused [code=120111] pjsip log: -- Called PJSIP/601/sip:601 at 192.168.1.55:5075;transport=tls <---

Sipml5 works. You need to have TLS enabled on asterisk web socket. Mitul On 12-Mar-2015 12:47 PM, "David Cunningham" <dcunningham at voisonics.com> wrote: > Hello, > > Can anyone recommend a particular online WebRTC phone for testing with > Asterisk? > > We tried: > > - JsSIP, but even with the "enable video" checkbox disabled it sends video >

CentOS Errata and Security Advisory 2020:5004 Low Upstream details at : https://access.redhat.com/errata/RHSA-2020:5004 The following updated files have been uploaded and are currently syncing to the mirrors: ( sha256sum Filename ) x86_64: 898a07f35eaa8781f7f96ee6666297c5864472115945d11efcee3bfabc801e33 resource-agents-4.1.1-61.el7_9.4.x86_64.rpm

Hello, I've enabled BT-200's SYSLOG logging, and I get some message whose meaning is obscure to me. In particular, in a day I got the "Deletion of invalid timer" message almost ten times from one phone, which has some call problems. Can someone point me to a resource on BT200 error codes? Thanks, -- Andrea Spadaccini Multimedia Technologies Institute s.r.l.