similar to: WANTED : Zaptel Patch - Dtmfthreshold

Hi all, we're buildin an Asterisk box based on an Intel IXP425 board. The board uses a Beronet BN2S0 ISDN card, mISDN 1.1.4 and asterisk 1.4.2. hfc_multi has been patched to compile under big endian cpu, and so also capi kernel files. All the modules seem to load correctly (configuration was made with misdn-init config), but when starting cha_misdn, asterisk outputs the following lines: P[ 1]

I have the same problem as the following: http://threebit.net/mail-archive/asterisk-users/msg36602.html I am using a b410p (Wildcard) in TE mode on 4 channels of ISDN2e and it totally fails to detect incoming DTMF. The newer mISDN drivers have a parameter "dtmfthreshold" where you can tune the volume above which DTMF detection is initiated. However (I've tried it) the newest

Hi, I have installed Asterisk 1.4 with mISDN with the install-asterisk.tar.gz script from beronet.com. On my system I have two cards, one a AVM Frit!Card Pci 2.0 and one HFC-S chip. I know both to work well with mISDN on my system from a previous installation. Now however, the AVM card works well at first glance, i.e. it "registers" incoming calls and works through the asterisk

Hi, I have asked this question months ago - i have "toggled down" all DTMF Recognizations in my Asterisk (no more features etc) and found more people which recognized the same problem, but i cant find any help for them and me. The Problem (short as possible) : In a randomly call in my business day some unit in my Asterisk System sends an randomly DTMF Tone, like "A"

Hi i've installed this software: ******************** SOFTWARE mISDN-1_1_7 mISDNuser-1_1_7 Asterisk-1.4.15 ******************** SOFTWARE misdn is correctly loaded by misdn-inist start Here there is the misdn.conf (copied from an existing and working installation with Asterisk 1.2.x and one BN8S0) ******************** MISDN.CONF [general] misdn_init=/etc/misdn-init.conf debug=0 bridging=no

Hi, i am from Germany, so excuse my School English. I use Asteriks 1.2.12.1, zaptel 1.2.9 and mISDN Rc25 - since my update of Asterisk 2 wooks ago, Echos accure in my SIP Calls. I use SNOM 360, sometimes there is no echo (for example if i call myself via SIP->Asterisk->SIPProvider->TELEKOM->ISDN) but if i call other people there occures Echo many times. The Routing is always the

I got an up2date Asterisk with SNOM360 as SIP and mISDN with 2 ISDN Cards, if i press in a call the "*" Asterisk, Asterisk destroys the call not, Asterisk lets him hang and do nothing, if i hangup, Asterisk tell me in the warnings-log that the bridging was not successfull ?! If have disabled the function to hangup in the features.conf, but the key is still available, can someone

Hi, I have done my best and tired of searching the net about the problem. If anybody could help would be a great favour. Description of Problem ------------------------ I am trying to install two Netpci cards(Traverse Technology Netjet ISDN-s) on Trixbox 2 and aim is to use in Asterisk as dailin and dialout. I compliled the driver as directed in the manufacture manual. After installation dmesg

I currently us Linksys/Ciscio, Grandstream and AudioCodes ata's. none of the three perform well in all enviroments. Between stablity issues, T38 and DTMF talkoff all three suffer some combination of issues. I am looking at Patton and Innomedia. Has any one tried either brand and what is your experience with them. Which would be the base for stability, audio quality, provisioning, DTMF

Hello, We have recently purchased two Supermicro servers, AS-1021M-T2RB (http://www.supermicro.com/Aplus/system/1U/1021/AS-1021M-T2RV.cfm), and have built them both with CentOS 5 operating system. They are identical, apart from the manufacturer of the disk drives. Kernel is: Linux version 2.6.18-8.1.6.el5 (mockbuild at builder6.centos.org) (gcc version 4.1.1 20070105 (Red Hat 4.1.1-52)) #1 SMP

Hello, I have some problems with mISDN. I can't send or receive call from the Billion ISDN card Mi configuration files are thoose: extensions.conf: [general] static=yes writeprotect=yes [SOME] exten => 101,1,Dial(SIP/101,30,Ttm) exten => 101,2,Hangup exten => 102,1,Dial(SIP/102,30,Ttm) exten => 102,2,Hangup include => outgoing [outgoing] exten

Hi i am experiencing some problem with asterisk and misdn i've patched and recompiled the 2.6.15.5 kernel on the server i use a BN8S0 card with alla channels in TE mode. i can load hfcmulti and mISDN_dsp i load this with: /sbin/modprobe hfcmulti layermask=0xf protocol=0x22 type=0x08 and then /sbin/modprobe mISDN_dsp dmesg returns me the following: Modular ISDN Stack core $Revision: 1.34

Hi All, We've got msidn configured: Port 1: TE-mode BRI S/T interface line (for phone lines) -> Protocol: DSS1 (Euro ISDN) -> childcnt: 2 -------- mISDN_close: fid(3) isize(131072) inbuf(0x8fd5060) irp(0x8fd5060) iend(0x8fd5060) and running on Asterisk 1.4.21.2: pbx*CLI> misdn show stacks BEGIN STACK_LIST: * Port 1 Type TE Prot. PMP L2Link UP L1Link:UP Blocked:0 Debug:0

Hi. When I call my RNIS numbers (with a mobile phone for example), I can see 2 incoming calls on the IPBX, which should not happend. I'm not sure if it's a problem with the telco France Telecom and their ISDN setup, or if it's a problem with the MISDN driver on the IPBX itself. I'm stuck ... Any advices for troubleshooting that? Someone provide working configuration files

Hi, I have Asterisk-1.2.18 install with FreePBX & more than 75 extnsion, daily I come accross an issue & try resolving them its either user learning curve or my ignorance. But, I dont know what to say regarding this issue. I have my Dial Plan for internal users to have a 3 Digit Extensions. So instance my Ext is 239 & someone dials the main #, its gets the

hi i am experiencing some problems with the configuration of an BN8S0 Beronet card. I've downloaded last CVS of mISDN ans mISDNuser, i patch the kernel 2.6.16.18 and the enabled the following: <*> ISDN support x x Old ISDN4Linux ---> x x --- CAPI subsystem x x <M> CAPI2.0 support x x [*] Verbose reason code reporting (kernel size +=7K) x x [*]

Hi list, I've installed Asterisk 1.4.0 with newest mISDN 1.0.4 + mISDNuser 1.0.3 on Fedora Core 6. I get many compilation error on mISDN. It wants to include linux/config.h That I fixed by removing the #include line at every occurance. (Don't know if that was a wise move, but it then compiled). mISDNuser and asterisk compiled fine, and asterisk can find and use the ISDN BRI port in

Hi all, I have a problem with my beronet card with 2 isdn. I think drivers and Asterisk are ok but the red led on the card always blinking. The card is connected with PBX. I post some conf: [root@gateway ~]# misdnportinfo Port 1: TE-mode BRI S/T interface line (for phone lines) -> Protocol: DSS1 (Euro ISDN) -> Layer 4 protocol 0x04000001 is detected, but not allowed for TE lib. ->

Hi all, I'm fighting with a really strange problem that is really busting me. I have an asterisk 1.4.22 ( from a trixbox 2.6.2 ) and mISDN 1.1.7 3 extension on hardphone and 3 extension in softphone ( zoiper ) What happens is that sometimes the people on the other side of communication hear my voice as metallic and chopped. This happen either on incoming call than on outgoing call. If I

Hi, Hi All, I've just delved into the world of asterisk and I'm having a few dtmf issues. Internally, amongst sip phones, dtmf is fine. Externally, if you ring from a GSM mobile, DTMF is fine, however if you ring from a standard phone, DTMF fails to register. I am attempting to use a quad port HFC-4S Beronet Card. I've been searching the web most of the last week and