Displaying 20 results from an estimated 3000 matches similar to: "Diva Server, chan_capi and tone detection"
2007 Apr 19
1
Improve voice quality on Asterisk + chan_capi + DIVA BRI
Hello everyone!
I've got a Eicon Diva Server BRI card into my "*" box working just fine,
but I wander if there's anything I can do to improve voice quality for
my operators. I'm thinking something along the lines of "auto gain" and
sudden noise suppression (like when you hit a fax machine or the other
party accidently touches the dial pad on the phone).
Does
2003 Nov 09
1
chan_capi & Eicon Diva problem
Hello,
I have an issue getting the chan_capi module to load in asterisk cvs
from today. Plain 2.4.20 kernel with melware patches for the Eicon Diva
Server Bri card.
I load the modules with: modprobe -v divas divacapi
I load the firmware with: divactrl load -c 1 -f ETSI -vd6
Output in /var/log/messages is:
Nov 9 19:26:26 voice kernel: Eicon DIVA - DIDD table
(http://www.melware.net)
Nov 9
2006 Feb 28
2
chan_capi and Eicon Diva
I am trying to use chan_capi with an Eicon Diva Server BRI.
I installed the Eicon drivers from source including CAPU and
I can use the board correcly using tty_test and minicom over /dev/ttyds01
or /dev/ttyds01.
I need to insmod capi ( why? it is not written anywhere) and then
capiinfo shows me all board parameters, but I have to break it otherwise
capiinfo doesn't exit at all, but I don't
2004 Sep 27
3
chan_capi, Eicon Diva server BRI, kernel 2.6?
Hi list,
Does chan_capi work with kernel 2.6? The Eicon Diva server card loads
fine judging from /var/log/messages but Asterisk gives an error when
trying to load the chan_capi module. I'm using chan_capi-0.3.5,
zaptel-1.0.0, libpri-1.0.0 and asterisk-1.0.0 on a Fedora box with
kernel 2.6.8-1.584. Zaptel and ilbpri work fine as does *. I have seen a
msg that may be related and don't know
2005 Jun 28
1
problems with chan_capi 0.3.5 , divactrl, eicon diva server, and kernel 2.6.10/2.6.12
Hello all,
I'm having problems getting chan_capi 0.3.5 to work well with an Eicon
Diva Server card using using the driver from linux kernel both 2.6.10
and 2.6.12 (vanilla versions).
I have a (really two) producci?n system(s) running chan_capi in another
identical Eicon Card using kernel 2.4.27 and the Diva Server drivers
from Eicon. I installed an compiled the source level rpm
2003 Apr 22
1
struggling with Diva 4BRI and chan_capi
Hi,
I am trying to configure a Diva Server 4BRI to work with chan_capi. Here
are the steps that I took:
- compiled fresh kernel with new-style CAPI support: i4l_divas_1.2
- got the divactrl_1.2 utilities, configured the card startup scripts,
- rebooted, card firmware loaded properly, "capiinfo" displays detailed
info on 4 controllers, however there is an error message:
FAC REQ -
2005 Mar 17
3
Compilation problem chan_capi and Eicon Diva 4Bri
Hi *,
I want to integrate the Eicon Diva 4Bri Card to Asterisk.
Eicon drivers and capi is installed. I use the latest dev version from
eicon compiled and installed for my fedora 2 system.
I found the chan_capi for asterisk from www.junghanns.net. Also loaded
the patch and applied to the chan_capi source tree.
I changed the Makefile to include the capi20.h from eicon:
2006 Dec 07
1
eicon diva BRI problems
Hi (Armin?) !
Today I had a problem with Diva Server 4BRI-8M 2.0.
Asterisk 1.2.12.1
chan_capi-cm-0.6.5
divas4linux-melware-3.0.f-106.622-1
Asterisk could not receive and make calls on the BRI ports, although the
ports looked fine within Asterisk.
I usually use "/usr/lib/divas/divactrl dchannel -c 1" to test line
activity. This time there was no activity (cryptic log
2005 Oct 02
3
[Sorta OT] Eicon DIVA with asterisk@home
Hi;
I've got an AAH installation where a customer wants to install an active
Eicon DIVA BRI card. AAH is built on Centos 3.5 which is currently at
kernel 2.4.21.37. Support for Eicon active cards is built-in.
I've debugged and run the A@H install-Eicondiva script but when I try to
run divactrl load -c 1 -f ETSI -Debug I get a response :
A: can't get card type for DIVA adapter
2005 Jan 17
0
voicemail sound distorted - chan_capi, diva, cvs-head
hi,
i have a problem with distorted voicemail sound on our asterisk test
machine.
i'm using cvs-head (2004-01-17) and chan_capi 0.3.5 (with my patches to
make chan_capi compile with asterisk cvs-head) and a diva quad-bri isdn
card.
other things work well with my setup (dial in, dial out, app_meetme) and
sound recordings from sip channels.
the problem is with voicemail and app_record,
2005 Dec 30
3
using a Gigaset SX440isdn on a Diva 4BRI ?
Hello,
I just received a couple SX440isdn phones and was wondering if they can
be plugged into a Diva 4BRI port in NT mode and work with
asterisk+chan_capi?
I know they probably work fine with mutliHFC cards with either bristuff
of chan_misdn but since I have some spare Divas, I was curious about
their potential as phone ports.
The Diva's 3 and 4 ports are already set to NT mode at boot
2006 Feb 02
2
ISDN Eicon Diva Server V-BRI
Dear all,
I'm planning to buying Eicon Diva Server V-BRI for my
asterisk server and run with chan_capi.
Is anybody using that card ? Would appreciate any feedback.
Bartosz
2004 Jun 10
2
Using Asterix and Hylafax with Eicon DIVA E1
Hi,
I would like to set up a high density FAX/PBX server, am looking at using
Eicon Diva E1 card with Asterisk and Hylafax sharing channels, is this
possible. I know Extensions can be reserved for voice OR fax with the
combination of chan_capi used for * voice, capi4hylafax on fax but then
channels must be dedicated rather than shared ie. would like to be able to
answer voice/fax on same DID.
2006 Apr 21
7
some EICON Diva 4BRI questions
Hi!
I have some (short) question about the Eicon DIVA (V-)4BRI cards I want
to have (short) answered before buying the DIVA card. I know there are
several Eicon guys active on the list, thus I ask on the list instead of
directly to Eicon so that all other will benefit as well.
1. Do Eicon DIVA (V-)4BRI cards support TE and NT mode?
2. Can the clock (master/slave) be configured independent
2008 Jan 08
2
Distorted audio over Eicon Diva Server BRI
We are experiencing slightly distorted audio with playing of recordings on
our Asterisk server when the call comes in over our Eicon Diva Server BRI
card. An example is an incoming call to IVR and playing some of the standard
Asterisk voice prompts. Note that there is no audio problem with internal
access to the same recording. Neither is there a problem with calls not
involving the playing of
2004 Sep 23
1
Diva Server PRI/E1-30
Hello,
Can I use the Diva Server PRI/E1-30 card with asterisk (with chan_capi or
i4linux) ?
If asterisk detect a fax, how divert the call to the onboard DSP ?
How can I handle the fax with hylafax (capi or pseudo serial device ?)
Thank you,
--
Carl
2007 Jan 25
1
Failing to compile chan_capi
I've got a brand new Eicon Diva Server BRI card and I want to configure
it with Asterisk. I managed to get asterisk and zaptel to compile and
install, I've compiled and installed the drivers for the Diva card and
now I need to compile and install the chan_driver for chan_capi.
Unfortunately this fails miserably. I get the following messages:
I'm using: Kernel 2.6.16.37.4,
2007 May 26
2
chan_capi install problems
I have installed Asterisk 1.2.18 am am trying to install chan_capi.
The current RPM
ftp://ftp.melware.net/Trixbox/chan_capi-1.0.1_1.2.14-1.i386.rpm installs but
Asterisk dies on startup. The following appears in the log:
May 27 03:28:18 asterisk1 kernel: divas: Diva Server V-4BRI-8 IRQ:7
SerNo:25290
May 27 03:28:18 asterisk1 kernel: divas: started with major 252
May 27 03:54:17 asterisk1 init:
2005 Mar 25
1
Eicon DIVA PCI ISDN cards (not server) work withasterisk!
Hello Marc,
Could you post the install details for the Diva PCI? I have a Diva Pro
PCI 3.0 and I am looking to get it working... I am running Debian
Testing. So far it appears there are a few things floating around but I
am not certain which direction to go. I know I need to load the firmware
first. I did manage to load the modules ok.
Thanks,
Greg
-----Original Message-----
From:
2003 Nov 08
5
Eicon Diva Server 4BRI
Hi Everybody,
Has anybody tried the above (or indeed any other 4XBRI cards) successfully
with Asterisk. As far as I can see the above mentioned card is an active
ISDN card but supported by it's own I4L driver. This leads to interesting
questions particularly regarding echo cancellations (which usually doesn't
work on the cheap passive cards with one exception as far as I can see).