similar to: SPA3k wired to PAP2 for echo testing

More an echo algorithm question than a purely asterisk one... I have the following setup: Handset - PAP2 - Asterisk - SPA3000 - Telco And no matter what I do, I get echo on a call routed out via the PSTN when I talk into the handset, in the order of a hundred ms (my estimate, could be wildly inaccurate!). Echo will occur also when I have a handset plugged into the phone port on the SPA3000

Arrggghh. Tearing my hair out here. I'm trying to set up the spa3000 in the UK for my home, and want * to control the dial plan I've googled to no avail. I've read the manual to no avail. Can someone, please let me know what the parameters is the spa and * are to a) receive a call from the pstn b) make a call to the pstn from the phone attached I can make sip to sip calls (i.e. I

My SIP phones can dial out through Sipura SPA3k to POTS for local and 911 calls _but_ incoming POTS calls are being swallowup somehow. Am I on the right track with the code snippit below? sip.conf: --------- In sip.conf the following code is _supposed_ to ring the SIP phones when a POTS line call comes in through Sipuara to Asterisk. [spa3k-pstn-in] ; Pots-line-in from Sipura ; If

Hello all, I have an ISDN termination box (TR1) that converts ISDN(Bri) to 2 normal analogue lines. The same number is assigned to these lines. These lines are connected to 2 spa3k registered to my asterisk box. When calls arrive, TR1 try to pass call to the first spa. If spa not takes the call immediately then try to pass to the other spa. The only configuration I found works is to put the

I am still haveing problems (echo) with my X100P but I'm thinking it has more to do with the server it is in which is not a negotiable item at this time. My question then is to the use of SPA3000's as a replacement from the FXO standpoint. 1. Can you setup the FXO port to recognize distinctinve ring and call a different context like you can do with Zap channels? Being able to call a

freebsd quite current ports tree 1.01 asterisk spa3k at 2.0.11(GWg) for calls in from the pstn side of an spa3k to asterisk, i get sporadic short beeps. they are not related to sip re-reg time, which is all that has occurred to me so far. calls in from the fxs side of the spa3k and out through nufone do not exhibit the beeps. calls from the fxs side of the spa3k out the fxo side do have the

> > That would be called a milliwatt generator. It likely exists in their > central office, but its typically used by their technicians to ensure > new installations meet specs and sometimes in troubleshooting. Call your > telco repair number and see if they will give you the telephone number > for it. I'll try that. 1st line technical support at Telstra are not known for

Ok, I am back from my thanksgiving holiday, and I find there was a big snow storm here in Seattle. Apparently during the storm there where multiple brown out/black outs. I have struggled since day one to get a high quality PSTN gateway configured with my very long loop and Mac based asterisk. I originally tried the HT-488, which had multiple issues, and was unacceptable. I then purchased

Using a spa3000 with asterisk cvs head, and the spa3k is config'ed with a dialplan that essentially routes any call starting with an "8" to asterisk. All other US 7 and 10 digit calls, 911, etc, route via the spa3k's fxo port. Is there a way in extensions.conf to: - inspect the dialed exten number, - if first digit is "8", drop the 8, - continue through each

Hello, Just want to tap the collective wisdom of this list as to experiences pertaining to the Handytone HT488 and the Sipura SPA-3000 adapters... Basically I'm looking for a FXO/FXS/LAN ATA and these two seems to be the top of the pick..Any comments and experiences esp. with Asterisk compatibility would be great, before I plonk in the bucks. TIA. /wai-sun

Does anyone have personal experience with a 5.8gig wireless phone (system) that has an MWI that WORKS with asterisk via fxs (in my case spa3k) generated MWI. I know the spa3k does stuttered dialtone but not sure if it generates FSK MWI. I see some that state they do but I also see reviews that say they don't. Doug

Has anybody else experienced problems with the Linksys PAP2-NA's? I've now had two of them fail unexpectedly, with no apparent rhyme or reason, having gone into a RED power LED, with a solid blue ethernet LED. No response from the device either on the network or from the phone.... To make matters even crazier, the one that now failed was the one I received as a replacement for the

The best I can do so far (which appears to be a bit of a hack) is (<:0>S0), which says to add a '0' to the start of the string and dial immediately. This gives asterisk an extension dialled of '0', which isn't the 's' that i'd hoped for, but is a good start! (S0) by itself doesn't work, nor does (<:>S0). Any other suggestions? Thanks James >

I need to be able to connect an old PA system to an asterisk box, which basically works as a couple of amplifiers taking an analogue phone signal and playing whatever it produces out of some speakers. There is no on-hook state in the whole setup. Obviously If I just connect the input to a port on an ATA, I'll just get a dialtone played through the speakers. Can anyone think of a way I can

Is there a way to configure the linksys pap2 to automatically connect to asterisk on lifting the handset (presumably into the 's' state)? Asterisk would then be listening for DTMF tones to figure out what to do rather than having to put a dial plan into each pap2. I think the pap2 is pretty much the same inside as a few of the sipura boxes so the same thing might work if anyone knows...

I've had an spa3k in service here at the house for a while now. After some initial wrangling, it's been working okay. I've had to reboot it a couple times and have noticed something rather annoying though. My setup is pretty simple and, dare I say, common. I have the SPA-3000 "inline" between my incoming POTS line and the internal house phone. It's setup to deliver

The TDM410P doesn't support 'hvac', only the obsolete TDM400P supports that option was for the old phones that have a neon light (or equivalent LED+ZENER ciruit). Are other phones off the TDM410P (other than the VTECH) working, or is the Vtech the only model with VMWI available to you. I'm not able to check at the moment, I have copied the asterisk-users list, someone else may

I'm trying to get working a spa3000 with asterisk. My problem is I cant get wroking the incomming calls (I installed the lastest firmware). My problem is asterisk is rejecting the authentication from the spa3000. Asterisk answers forbidden (SIP/2.0 403 Forbidden) and I think I placed the username and password correctly... Sip.conf says this: [linea2] username=linea2 type=peer secret=1111

Have you thought about making them agents, they would both be reachable by dialing there agent number then, and I know only one agent can be logged in at once. Just a thought. -----Original Message----- From: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com] On Behalf Of asterisk-users-request@lists.digium.com Sent: Saturday, April 22, 2006 8:26 PM To:

Hi, I have 3 PAP2 connected to *, they work fine but there are some things which I would like to improve, some of them are: - double ring tone when placing a call (I hear two tones it seems like the PAP2 is generating it's own tone) - some kind of noise (like glitches or something) when I pick up the phone (seems like some polarity thing) - I'd like to keep the tone after