similar to: echo with spa-3000

In my seemingly endless search for the cause of echo on my SPA3000, I wired it up in the following configuration: Analogue Handset <--> (FXS)SPA3000(FXO) <--> PAP2 And set the Line1 dialplan on the SPA3k to '(<:@gw0>S0)' which means that as soon as I pick up the handset I get linked straight through to the PAP2, which gives me dialtone. Even in this configuration, with

Hallo! I had ordered a Sipura SPA-3000 in the UK, but the supplier turned out to be unreliable and never shipped. Yesterday I went looking for alternative suppliers and found the Linksys SPA3000 device. It's a different box, but the specs look very similar. Is this the same device? Has anyone used this Linksys SPA3000 successfully with Asterisk? Thanks, Frank

Any ideas ????? Jonn -------- Original Message -------- Subject: [asterisk-users] Internal LAN echo problem Date: Wed, 24 Oct 2007 08:34:32 -0500 From: Jonn R Taylor <jonnt at taylortelephone.com> Reply-To: Asterisk Users Mailing List - Non-Commercial Discussion <asterisk-users at lists.digium.com> To: Asterisk Users Mailing List - Non-Commercial Discussion <asterisk-users

> > That would be called a milliwatt generator. It likely exists in their > central office, but its typically used by their technicians to ensure > new installations meet specs and sometimes in troubleshooting. Call your > telco repair number and see if they will give you the telephone number > for it. I'll try that. 1st line technical support at Telstra are not known for

Hi there everyone! I've bought a Sipura SPA 3000, and succesfully connected it to my Mac, where I installed Asterisk 1.4.0. Both ports (FXO and FXS) are well configured). However, living in Brazil, I'd like to know if there are optimal settings to my PSTN that I should enter into the config of the device. I experience a little bit of echo on the FXO probably because I raised the gain of

First off I am totally annoyed and let down by PC World Business (PCWB part of the Dixons Group). I ordered one of these babies from them over a month ago. After constantly chasing them up they finally told me they couldn't deliver, and have now only just returned the money they "stole" from me. I only bought from them because they showed a 4-day availability stock level! Now

Hello All! I am in the process of assembling an asterisk-based phone system for my office - using SPA-3000s to connect the network to the PSTN. I am wondering if anybody else can get (or has already seen) the same behaviour out of their 3000. The short version: Send multiple Calls to the SPA's FXO port at the same time it is re-registering with Asterisk. SPA HTTP Configuration:

The TDM410P doesn't support 'hvac', only the obsolete TDM400P supports that option was for the old phones that have a neon light (or equivalent LED+ZENER ciruit). Are other phones off the TDM410P (other than the VTECH) working, or is the Vtech the only model with VMWI available to you. I'm not able to check at the moment, I have copied the asterisk-users list, someone else may

The best I can do so far (which appears to be a bit of a hack) is (<:0>S0), which says to add a '0' to the start of the string and dial immediately. This gives asterisk an extension dialled of '0', which isn't the 's' that i'd hoped for, but is a good start! (S0) by itself doesn't work, nor does (<:>S0). Any other suggestions? Thanks James >

Is there a way to configure the linksys pap2 to automatically connect to asterisk on lifting the handset (presumably into the 's' state)? Asterisk would then be listening for DTMF tones to figure out what to do rather than having to put a dial plan into each pap2. I think the pap2 is pretty much the same inside as a few of the sipura boxes so the same thing might work if anyone knows...

Arrggghh. Tearing my hair out here. I'm trying to set up the spa3000 in the UK for my home, and want * to control the dial plan I've googled to no avail. I've read the manual to no avail. Can someone, please let me know what the parameters is the spa and * are to a) receive a call from the pstn b) make a call to the pstn from the phone attached I can make sip to sip calls (i.e. I

I've a problem. I've some spa3000 and spa2100. Asterisk 1.2.4. Prefered codec g711u in both. Calleng from a fxs of spa2100 to the fxo of spa3000, all works ok. Then I call from a sip phone configured for using g729, to the fxo of spa3000, it also works ok. The problem is that after this, when, making again a new call from spa2100 to spa3000, spa2100 receives only white noise. I suspect a

Hello, Before throwing in the towel with my Sipura 3000 has anyone had much success with that adapter connected to a door phone? In our setup a doorphone is connected to the SPA's fxs port. When a visitor rings, asterisk calls a group of Polycoms and the person who answers has to enter *1 to trigger the door opening. However it seems the SPA doesn't relay the DTMF's to the

Hi all, I was wondering whether anybody here would help me clarify this minor issue please. If I have the following setup; Asterisk ------ Sipura SPA 3000 (fxo) --------- Pstn Line Would a call coming in on the pstn line be answered by the ATA or just get passed through to the * server (depending on dialplan) to handle? So basically, the caller does

Has anybody else experienced problems with the Linksys PAP2-NA's? I've now had two of them fail unexpectedly, with no apparent rhyme or reason, having gone into a RED power LED, with a solid blue ethernet LED. No response from the device either on the network or from the phone.... To make matters even crazier, the one that now failed was the one I received as a replacement for the

Ok, I am back from my thanksgiving holiday, and I find there was a big snow storm here in Seattle. Apparently during the storm there where multiple brown out/black outs. I have struggled since day one to get a high quality PSTN gateway configured with my very long loop and Mac based asterisk. I originally tried the HT-488, which had multiple issues, and was unacceptable. I then purchased

I'm new to asterisk and already a fan. Please forgive me if my questions are covered by some FAQ and thanks in advance for any pointers anyone can give me. The basic problem that I'm having is that sometimes outgoing calls result in a busy signal when the outgoing line is free. I'm thinking that the channel is timing out or something but haven't figured out how to debug or gather

Voxilla.com has a great config wizard for the SPA-3000 and * http://voxilla.com/spa3kasterisk.php I took the output from this wizard and dumped it on my test box with an SPA 3000 (with some mods to match my * contexts) and everything worked great. Calls from the PSTN to the spa3000 are routed to dialplan #8 on the spa3000, which dials * Both the FXO and FXS port register with * The SPA3000 is

I've had an spa3k in service here at the house for a while now. After some initial wrangling, it's been working okay. I've had to reboot it a couple times and have noticed something rather annoying though. My setup is pretty simple and, dare I say, common. I have the SPA-3000 "inline" between my incoming POTS line and the internal house phone. It's setup to deliver

Hi, all I am trying to figure out how to forward incoming PSTN call on SPA3000 to VoIP extension(s). Basically, I have converted my home to VoIP. I have normal phone (connected to SPA3000) and couple of IP phones. All call coming from VoIP DID do ring all phones (analogue via SPA3000 and IP ones). Now I need to do same thing for incoming PSTN calls. I have enabled gateway function in SPA3000 and