similar to: Diva server 4bri and Portuguese BRI

Hi (Armin?) ! Today I had a problem with Diva Server 4BRI-8M 2.0. Asterisk 1.2.12.1 chan_capi-cm-0.6.5 divas4linux-melware-3.0.f-106.622-1 Asterisk could not receive and make calls on the BRI ports, although the ports looked fine within Asterisk. I usually use "/usr/lib/divas/divactrl dchannel -c 1" to test line activity. This time there was no activity (cryptic log

Hi (Armin)! Does someone knows how to identify the type of the card? The delivery note says it is a V-4BRI-8M, whereas lspci reports a 4BRI-8M. What is it really? Are there any Eicon tools to identify the card type? thanks klaus 0000:0a:03.0 Network controller: Eicon Networks Corporation Diva Server 4BRI-8M Rev 2 (rev 01) Subsystem: Eicon Networks Corporation Diva Server 4BRI-8M Rev

Hi! This weekend we had a problem with our Asterisk Box which ran flawlessly for nearly 4 weeks. The Asterisk server sits between the PSTN and a Siemens PBX and bridges 2 BRI lines. No calls, not incoming, not outgoing. The admin rebooted the Dell Box and then everything worked fine again. Now, I'm analyzing log files to find the cause. During the Asterisk outage the logfiles only show

Hello, I just received a couple SX440isdn phones and was wondering if they can be plugged into a Diva 4BRI port in NT mode and work with asterisk+chan_capi? I know they probably work fine with mutliHFC cards with either bristuff of chan_misdn but since I have some spare Divas, I was curious about their potential as phone ports. The Diva's 3 and 4 ports are already set to NT mode at boot

I am trying to understand the difference between the divas4linux available from the Eicom/Dialogic website and the melware version. Am I right in thinking that the melware version is for Trixbox or Asterisk but the Dialogic version is for Asterisk only (i.e. will not work with Trixbox?). I've noticed that some of the things mentioned on the Dialogic web site as included with Divas e.g.

I have read most of Eicons information on Q.SIG, and I am able to load the Q.SIG protocol (instead of ETSI for example). No strange logging in divacrtl mlog. But how do I tell Asterisk to understand Q.SIG? My PBX is configured for QSIG, but I cannot see anything on my trace when trying to make a call via the S0(Q.SIG) Janne > -----Ursprungligt meddelande----- > Fr?n:

Hi, I have done my best and tired of searching the net about the problem. If anybody could help would be a great favour. Description of Problem ------------------------ I am trying to install two Netpci cards(Traverse Technology Netjet ISDN-s) on Trixbox 2 and aim is to use in Asterisk as dailin and dialout. I compliled the driver as directed in the manufacture manual. After installation dmesg

Hi; I've got an AAH installation where a customer wants to install an active Eicon DIVA BRI card. AAH is built on Centos 3.5 which is currently at kernel 2.4.21.37. Support for Eicon active cards is built-in. I've debugged and run the A@H install-Eicondiva script but when I try to run divactrl load -c 1 -f ETSI -Debug I get a response : A: can't get card type for DIVA adapter

Has anyone a working /etc/asterisk/capi.conf example for Germany or Switzerland using the AVM C4 - ISDN Card. I try to connect asterisk to 3 wires BRI-ISDN (Swisscom). I appreciate your help and it would save me a lot of time, figuring it out by myself. regards, Claudio

Hi, I'm trying to get an Eicon Diva Server4BRI card running under Ubuntu 6.06 - by downloading the v3 driver package from Melware and compiling everything. Yet, after activating the necessary modules (divas and divadidd) and interactively configuring the card (/usr/lib/divas/Config), starting up the adapter fails! The error "/usr/lib/divas/divactrl load -c 1 -Debug" produces

I have a Diva Server BRI installed in a Debian system running Asterisk 1.2.22. When a call comes in the Background application plays a couple of times. Halfway through the second time, the call is disconnected (total time connected about 25 seconds). I've posted various configs below. Any advice on how to debug would be appreciated. We are located in New Zealand. CLI showing capi debug (just

Hello, I have an issue getting the chan_capi module to load in asterisk cvs from today. Plain 2.4.20 kernel with melware patches for the Eicon Diva Server Bri card. I load the modules with: modprobe -v divas divacapi I load the firmware with: divactrl load -c 1 -f ETSI -vd6 Output in /var/log/messages is: Nov 9 19:26:26 voice kernel: Eicon DIVA - DIDD table (http://www.melware.net) Nov 9

Hi Armin! I have problems on debian sarge with standard 2.6.8-2-386 kernel. I've installed the packages: kernel-headers-2.6.8-2 kernel-headers-2.6.8-2-386 kernel-image-2.6.8-2-386 kernel-kbuild-2.6-3 kernel-source-2.6.8 Then I unpacked the kernel sources into /usr/src/kernel-source-2.6.8 and made a symlink from /usr/src/linux --> kernel-source-2.6.8 Then I entered

Hi all, I'm new to asterisk and not too knowledgeable on ISDN, so please be gentle :) I have a dual-channel Eicon Diehl Diva card in a Debian Woody box with kernel 2.4.27, connecting to a Telstra (Australia) Onramp Home Highway ISDN line. I'm pretty certain the card and line both work since they've been used in this machine for PPP before this (but with an older kernel with DoV

Hi Everybody, Has anybody tried the above (or indeed any other 4XBRI cards) successfully with Asterisk. As far as I can see the above mentioned card is an active ISDN card but supported by it's own I4L driver. This leads to interesting questions particularly regarding echo cancellations (which usually doesn't work on the cheap passive cards with one exception as far as I can see).

Are there any step by step instrunctions on how to install drivers and I guess bristuff for this card? Just need to use it to handle voice on 2 BRI circuits (UK) then utilise with Asterisk and some Digium cards handling POTS phones (and some VoIP out the back). It's the EICON card stuff and how to make it all work I'm finding confusing? Steve -- NetTek Ltd UK mob +44-(0)7775 755503

Hi, I am trying to configure a Diva Server 4BRI to work with chan_capi. Here are the steps that I took: - compiled fresh kernel with new-style CAPI support: i4l_divas_1.2 - got the divactrl_1.2 utilities, configured the card startup scripts, - rebooted, card firmware loaded properly, "capiinfo" displays detailed info on 4 controllers, however there is an error message: FAC REQ -

Hey guys This is probably for Armin, but I thought maybe someone else might have something I could try. I'm having a problem with one of my Eicon Diva V-4BRI cards and I'm trying to work out if its a driver configuration error, card failure or telco problem: I have an Asterisk box running -- the Eicon drivers see all four ports on my card, capi.conf is configured with all four ports

Hi *, I want to integrate the Eicon Diva 4Bri Card to Asterisk. Eicon drivers and capi is installed. I use the latest dev version from eicon compiled and installed for my fedora 2 system. I found the chan_capi for asterisk from www.junghanns.net. Also loaded the patch and applied to the chan_capi source tree. I changed the Makefile to include the capi20.h from eicon:

Hi Guys! I got a Diva passive ISDN card and I can't get it work with asterisk 1.4, It is supported in the kernel as an isdn4linux device but I can't find "Modem" channel type when i type in: core show channeltypes. I'm guessing it is removed in asterisk 1.4. Tried with capi interface but it does not work :( Anybody got some idea how can i make it work or got a link to a