similar to: Clicking Noise on Pure Voip Calls

Hi i test a new equipment on my backbone: a Cisco AS5300 with voice dsp ressource connected at a E1 Voice Link. I want that all call incoming on the cisco 5300 are sent to Asterisk and all Asterisk outgoing call are sent to Cisco AS5300. Actually, i configure the AS5300: isdn switch-type primary-net5 ! voice service voip sip ! voice class codec 400 codec preference 1 g711alaw codec

Hello, I've got an ISDN PRI circuit terminating in a Cisco AS5350, which in turn is talking to an Asterisk server via SIP for call origination and termination. Seems simple enough, and it works for the most part, but: 1) Caller ID name data comes in on the PRI, but doesn't appear to get handed off to the Asterisk server via SIP, at least not in any format that Asterisk

Hi all, Firsts of all, let me say that I'm new to asterisk. I have some time suscribed to the list reading a lot of your messages and trying to learn a lot. The case is: last week I installed an asterisk server in the following scenario: PBX --- CISCO_ROUTER ---- ASTERISK The calls that are routed within the asterisk work perfect, there is not problem. However, the calls that are

HI, I have been pulling my hair out trying to get a Cisco MC3810 to interface my Asterisk box with a T1. I am able to make outgoing calls but incoing calls never reach my Asterisk box. The cisco give a fast busy when I try to call one of the DID's. When playing around with the dial-peers I can get the cisco to pick up the call, but then it forwards the call back to the ANI that is dialing.

Folks, I have a NEC 2400 pbx(non-voip) behind a Cisco 3725, connected via standard wic-t1 card. The NEC needs to call two different asterisk servers with 4 digits. I have two way calling working with the one * box, but the other is perplexing me. Here's the layout * <--> Cisco 2811(192.168.13.1) <--> 1.54 point to point <- Cisco 3725(192.168.8.1)<-> NEC 2400. The

Hello, everyone. Right now, we are trying launch our own PBX system based on Asterisk(Fedora) with Cisco 2611. Cisco has 2 port FXO card installed on it. For testing, I have 2611 hooked into phone line with number of xxx-xxx-xxxx fine. (I'll call it F). Using softphone, I can dial in extension 1001 on asterisk, which should talk to cisco. After initial connection to Asterisk, I have try to

I have 2610 XM with 1 Fastethernet and VIC2-2BRI. Dialin and dialout over pots is ok. Also inbound pots calls get redirected to Asterisk y.y.y.y So far so good. But I want to setup VOIP sessions with local carrier. I added dial-peer 40 for this. Session target x.x.x.x But calls will always get routed to the pstn peers 50 and 60. Peer x.x.x.x is never contacted or tried. My situation: PSTN

Hi, I am upgrading a Cisco 7960 phone from SIP V.5.1 to 6.0 and then will to go up to 7.5 However in my first attempt to go from V.5.1 to 6.0 this is hat happens: - The phone reboots - The phone then reads the file OS79XX.TXT from the TFP server. In the file I added the version "P0S3-06-0-00" - It starts upgrading firmware - Then I get the following message: (Upgrade Failed -

I have the following configuration and am obviously missing something small that is causing * not to work as expected. I have the following defined in sip.conf [ccme-in] type=peer host=10.0.9.1 context=devel_in disallow=all allow=alaw nat=no canreinvite=yes qualify=yes and [devel_in] is defined in extentions.conf However when I try to call via the dial peer I have configured on the cisco

Does anyone in here know how to setup auto negotiation between g729 and g711ulaw on a cisco 5400? I would imagine it would be the same on a 3660. The problem I am having is natively the call is setup for g729 however when the call is transferred to voicemail it uses ULAW so when the cisco tries to connect to the voice mail I get a SIP error that the codec couldn't be negotiated. I need

I see a lot of comments but no actual show runs. Can someone post a 7206 config. I am having a dickens of a time getting calls to pass. I currently have the following loaded. Cisco IOS Software, 7200 Software (C7200-IK9O3S-M), Version 12.3(8)T6, RELEASE SOFTWARE (fc2) Thanks !!! Jerry -- No virus found in this outgoing message. Checked by AVG Anti-Virus. Version: 7.0.344 /

Hello, I'm trying to receive faxes with asterisk. My configuration is like this: PSTN fax -> ISDN -> Cisco router with VoIP module -> Asterisk When I try to send a fax from PSTN fax I got the standard fax signal, Asterisk starts rxfax application and then call ends and there is no tif anywhere. On the fax display there is still one message: Calling... Part of my extensions.conf:

Hi, The ldN like intrinsics (including all the ld1xN, ldN, ldNlane, ldNr, stN, stNlane) can use any pointer types. The definition (in IntrinsicsAArch64.td) of such intrinsics use 'LLVMAnyPointerType', which means we can pass any pointer type to such intrinsics. E.g. I tried following case ld2.ll: define { <4 x i32>, <4 x i32> } @test(float* %ptr) { %vld2 = call {

Hello list, is there any open-source software that recodes g729 sound files to wav sound files ? The only way (at least) to do such transformation is with interactive form on: http://www.asteriskguru.com/audio_conversion.php Tofik Suleymanov

Hello. I have been searching the archives for a simple, clear listing of the available codecs with total size, plus the data and overhead sizes. Does anyone have this handy, and can it be added somewhere, even the wiki. Regards...Martin -- The system will be down for 10 days for preventive maintenance.

Hello; I have a SIP trunk with a service provider, the caller from landline or mobile is hearing us very well, but the agent who is sitting on the handset is not hearing well, the voice at the agent is not crystal (like he is talking from well or far deep place). Although the IP Phones are cisco 7942G and the used codec is g711ulaw (actually it gave better quality than g711alaw). If we increase

We appear to be having a problem with our asterisk setup. We have a cisco AS5300 with pri lines coming in and passing the calls onto asterisk then too the sip phones. the phone call from the sip phones (7960's) appears to be ok nice and clear including the user who has called in. but if your the user who has called in its all crackley sounds really bad when they speak. i believe this

Hello, Has anyone experienced a segmentation fault in asterisk for using G729 against an AS5300 in SIP ? I'm having this problem. Also, any other codec I use gives me incompatible media (can be read in SIP DEBUG messages). AS5300 configured for multiple codecs, so is Asterisk. Tried G711u/A G723 and G.729. Any clues ? Regards, Jorge A. Info: Asterisk ver 1.0.7 stable Using AMPortal

I am testing asterisk-1.2.1-15 on RedHat 9(i386) for SIP-to-SIP call and i found a strange problem. When an extension gets a ring and it picks up the call a "tick" sound comes at start. This happens on both sides. I tried Xten's softphones and also hardphones. A thing which was common in both(soft/hard phones) was the selected codec. When i used g711ulaw on both soft/hard phones

Hi All Total noob on the list so all help appreciated.... I've successfully installed Asterisk on an IBM A30P Thinkpad using fedora Core 2 (I'm looking at having a mobile PBX for conferences and shows). I've plugged in two Cisco 7960 phones.... The phones register with the Asterisk correctly and I can run the demo's and even the AIX demo through to digium works correctly.......