similar to: lots of registrations, sip problem

Recently, I've been having issues with the URIs returned from e.164.org and toll free calls. It seems that the URIs that are returned from ENUMQUERY and ENUMRESULT are no longer the proper numbering schemes that the poviders use. I've been using the following [enum] template in my outbound route for quite some time with great success until recently. [enum](!) exten =>

Asterisk 11.1.0 One queue with strategy=leastrecent. (Full queues.conf below.) Occasionally (several times today), a caller will get "stuck" in the queue - there are operators available to take the call, but the caller stays in the queue for a long time. Any idea what might cause this, or where I can start looking to debug it? I'm going to start digging through the queue log

I'm reposting this to the list.. My spam filters didn't like the list host. :( If anyone was able to respond to the mail below, can you send it again please? Thanks. ------------------------------------------------------------------------- Hi, I'm having trouble explicitly forcing a codec between sip devices. Am I missing something or is this not really possible? I have a

3rd attempt to post it to the list, please ignore if it is duplicate I have the following problem When trying to setup asterisk 13.1 with PJSIP to connect to my IPV6 capable SIP provider the registration fails. [code][Dec 22 19:24:24] DEBUG[25247] pjsip: tsx0x110736c .Transaction created for Request msg REGISTER/cseq=36181 (tdta0x721d90) [Dec 22 19:24:24] DEBUG[25247] pjsip:

Hello list, my case is as follows: SIP1--asterisk--SIP2. SIP2 is IVR type device. SIP1 and SIP2 both use g729. When SIP1 calls SIP2, it hears the IVR, and prompt the SIP1 to punch the keypad on the phone. As suggested by you, I need to configure the SIP1 with out band dtmf mode , what is about the sip.conf, should I specify the SIP1 with demfmode=rfc2238 ? do I also need to make same kind

I've setup a SIP channel between two Asterisk box, and use Manager API to generate some calls. It's working quite fine, except this message (on the caller-side) : Jan 10 18:18:09 WARNING[25046]: chan_sip.c:6805 handle_response: Forbidden - wrong password on authentication for INVITE to '"sip1" <sip:asterisk@192.168.1.200>;tag=as77e9ebbb' But the call is going

Hi, I'm having trouble explicitly forcing a codec between sip devices. Am I missing something or is this not really possible? I have a grandstream registering to asterisk, named sip0. Sip0 registers, via sip, to another asterisk box, sip1. When I place a call from the grandstream, it will travel through sip0 to sip1, where it is then placed to the PSTN. Nothing can reinvite, this path is

Grrr. I'm using outlook web access and there's no way to do inline replies. Anyway... Gabriel. Using SER does not create a single point of failure. You install three SER boxes. Single point of failure gone. It does not take several seconds. If your phones are configured for SRV, and 2/3 of your SER boxes down, it takes about 2s. That's not bad for a 2/3 system failure. You can

Hi I have just been struggling for four days to get SIP working and now as I created a voicemail box, Asterisk has become very unstable and it can't bridge SIP phone to SIP provider calls anymore. Calling internally from one SIP phone to another works fine. Calling internally from a SIP phone to an analog phone on a Zap channel and vice versa works fine. Incoming PSTN calls delivered to

Hello to all. I have a couple of budgetones connected to Asterisk server. I can establish calls using budgetone with no problem, but when I hang up a Budgetone, Asterisk does not detect the hangup. It seems that the communication goes on in spite of budgetone's hangup. My sip.conf: [general] disallow=all allow=ulaw bindaddr=172.16.60.21 [sip1] callgroup=1 pickupgroup=1 type=friend

Hi, I've seen some answers to this on the mailing list archives but nothing that seems like the right answer. What I want is for 2 SIP phones to use speex to talk to each other through 2 asterisk boxes (linked over IAX2) while only supporting ulaw on the asterisk boxes themselves. I think a diagram will help ;) SIP1 <--> *1 <--> IAX2 link <--> *2 <--> SIP2 I want

Hi :) I hope someone has a hint concerning Early Media. The situation: My Asterisk is connected to small local carrier who works with several SIP servers. I traced some SIP headers and find something like this: Via: SIP/2.0 UDP sip1.provider1.de In the SDP part I found something like this: o=- 2268929 0 IN IP4 sip2.provider1.de c=IN IP4 sip2.provider1.de If I send

I set up my * server using its publc IP address. Now that i switch over to using the domain name, X-Lite can't log in. =========With Domain Name (doesnt work)============ Transmitting (NAT) to 85.250.206.46:6007 <http://85.250.206.46:6007>: SIP/2.0 401 Unauthorized Via: SIP/2.0/UDP 85.250.179.93 <http://85.250.179.93>

I would like to put srvlookup=no in my SIP conf, so that I don't get DNS issues (Asterisk stops responding). I use VoIP Buster and in sip.conf I use sip1.voipbuster.com. When I do sip show peers in CLI I get voipbuster/tomo 194.221.62.207 5060 OK (27 ms) And when I ping sip1.voipbuster.com [root@tomo ~]# ping sip1.voipbuster.com PING sip1.voipbuster.com

Without using Dundi or SER, any thoughts on the following anyone? Has something similar been implemented anywhere so as to me not having to horribly butcher code... 4 servers SIP1-4 User1 -- -- SIP1 -- \ / \ User2 ------ Go to register ------- SIP2 ----- Whereis? --> DB / \ / User3 --

Hey, You know, the Digium guys said both are good. They said the the DNS method is better because you dont have the extra point of failure (SER) but said the SER method is better in that it gives you more exact control in the handling of the calls and registration. They did acknowledge there would be a possible downtime only for incoming calls to users with dynamic IPs if the

Hi, Trying to properly broadcast / relay DTMF digits to other confbridge users, but does not appear to work. Goal is to have a conference user be able to receive the DTMF, so it has the effect of being 'broadcasted.' I have the following set up in 'confbridge.conf': dtmf_passthrough=yes From logger.conf, I can see the DTMF tones via setting "console => dtmf". When

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 i fixed wrong capi.conf (there was [controller1] after [interfaces]) now capi.conf is: ; ; CAPI config ; [general] nationalprefix=0 internationalprefix=00 rxgain=0.8 txgain=0.8 [interfaces] msn=855285,859609 incomingmsn=* controller=1,2,3,4 softdtmf=0 accountcode= context=local ;echosquelch=1 ;echocancel=yes ;echotail=64 ;callgroup=1

Hello, I'm trying to receive a fax to my inbound number from voipbuster. Asterisk receives the call and starts the rxfax application successful, but then nothing happens. The calling party is still hearing a ringing tone, or sometimes nothing. Voicecalls are working correct and without problems. For testing I've add a local number (300) to the dialplan. When I call this number