similar to: Stripping digits on internal calls

I've been going back and forth with my telco for several days, trying different configurations to get a new PRI to come up. The bchannels are all up and the T1 is not in alarm status. The dchannel refuses to come up however. We've tried ni2, qsig, and now dms100 for the switchtype. The telco tech I've been working with says that he's been sending "reset all channels"

Hi all, I am new to asterisk, but experienced with Linux and Avaya/Lucent G3R hardware/software. We currently have a large inventory of spare Lucent 64XX phone sets. I'm considering setting up an asterisk system for a remote office, and would like to use the Lucent sets because they are cheap, and familiar to my end users. Does anyone know of a card that can drive these sets? I think

Anyone configured a E1 PRI in Kuala Lampur, Malaysia with TM Malaysia? What signaling did they provide, framing, formatting? primary-4ess Lucent 4ESS switch type for the U.S. primary-5ess Lucent 5ESS switch type for the U.S. primary-dms100 Northern Telecom DMS-100 switch type for the U.S. primary-dpnss DPNSS switch type for Europe primary-net5 NET5 switch type for UK,

Dear all I have now install TE210P 2 port E1 card on asterisk 1.4.10 on centOS 5 but thing is that i have connect 1 E1 port with avaya E1 back 2 back and second E1 card on Direct Telcom for outgoing for outside now i got this error when i call on avaya PRI asterisk think PRI_CPE and remote end also CPE i have configure /etc/zaptel.conf span=1,1,0,ccs,hdb3

Hi all, I'm planning on connecting our Asterisk to our legacy PBX (an Avaya INDeX). I was originally going to sit it between our ISDN connection and the INDeX (tried it, worked ok) but now I intend to hang it off a spare PRI card just so should the * fail we keep our ISDN's at the INDeX, yes I've looked at ISDNguard but little info from the manufacturers. Anyhow, I'm now

*I'm trying to build an application that provides statistics of calls*>* and call recording. Someone told me this could be done out of band*>* with a SPAN (?) port that would replicate SIP and media packets to a*>* separate NIC without having to actually pass the real-calls thru*>* asterisk. It was explained that this SPAN port would in the SBC*>* would replicate data

Dear all I have setup with mediant 2000 with avaya now i want to install E1/PRI card with asterisk and trunk with E1 with Avaya E1 port so i want to buy E1 card for asterisk so which card is best and cast effective for my setup i want 1 port E1 card so can you suggest me which card is best for my setup and i want QSIG singaling with avaya Regards satish patel

Hi again, Well - I didn't see beta8a-2.3.3 in custom dir. Will try. Also I tried to contact Sangoma - they are very fast to answer but main problem is time difference - it's 6 hours between Canada and Europe. Br, dmitry Dmitry Zhukovski System developer ComX Networks A/S Naverland 31, 2 DK-2600 Glostrup Denmark Phone: +45 70 25 74 74 Fax:???? +45 70 25 73 74 Web: www.comx.dk

LS, I've create on the SCO unix the same loginname as on my winNT pc sharing a directory is no problem I have read and write access to it. The problem arise when I try to login from another winNT account let say yoyo then a pop-up windows appears. When I fill my origineel account with password I am refuse. Does someone know how to solve this? dump of my smb.conf file: [global]

Hi List, Merlin Magix hardware v02 I'm trying to get asterisk to act as a voicemail server for a lucent merlin magix PBX that we purchased used. We have 4 FXO channels between the two PBXs on a Sangoma A200 card. The 770 dialgroup is working properly, in that calls to 770 are answered by Asterisk. The magix is sending mode codes in the format #XX#XXX#, where the 2nd block of digits

Hello, We want to make H323 calls between asterisk and avaya(lucent) pbx. We create node-name,H.323 signaling group,trunk, but we can not make H.323 calls to asterisk. Also no warnings exist in debug. Instead of giving the IP of Asterisk ,i give my computer's IP and run SJPhone ith H.323 GUI. In this time, connection is established. SJPhone accepts H323 calls but Asterisk does not. Do

Hello, Have you tried the wanpipe-beta8c-2.3.3.tgz release in the custom/2.3.3 dir on their FTP site? Also, have you contacted Sangoma for support? They are very responsive. I am using wanpipe-beta8a-2.3.3.tgz and it's been working great on my A104 for a week now. MATT--- -----Original Message----- From: Dmitry Zhukovski [mailto:DZH@comx.dk] Sent: Monday, May 09, 2005 5:20 AM To: Asterisk

Hello, We are having issues with a NEW Sangoma A108D: -- Executing [691918892 at pbx1:1] Dial("SIP/xtravoip200-009d24b0", "DAHDI/g0/691918892|30|m") in new stack [Oct 1 10:04:43] WARNING[14171]: channel.c:3170 ast_request: No translator path exists for channel type DAHDI (native 76) to 256 [Oct 1 10:04:43] WARNING[14171]: app_dial.c:1237 dial_exec_full: Unable to create

Hi, after many issues we finally managed to make our system do outgoing calls with perfect quality. However I cannot detect *any* form of incoming call. when I use an outside phone to call the E1 connected to the sangoma a102, I instantly get a fast busy tone. My /etc/zaptel.conf is: loadzone=us defaultzone=us #Sangoma A102 port 1 [slot:1 bus:4 span: 1] span=1,0,0,ccs,hdb3 bchan=1-15,17-31

The company I work for has deployed an Avaya IP phone system. They have deployed the Avaya 4602 and 4620 IP telephones. They might be sending me one of these phones for use in my home office. Question: Can I make this IP telephone register and work with my Asterisk server? I don't know if it is a SIP phone? I searched thru the Avaya site, but can't find whether it's a SIP phone or

Do you have any extension in default context of your extensions.conf file to accept incoming calls ? It must be something like; exten => 12345678,1,Answer() exten => 12345678,2,Playback(Welcome) ... 12345678 = The DID number you are calling to reach E1 Idris -----Original Message----- From: Erick Perez [mailto:eaperezh at gmail.com] Sent: Thursday, July 26, 2007 7:03 AM To:

I'm trying to connect an Asterisk system to an Avaya Partner ACS R6 system. The problem I'm having is that I cannot get the partner system to get CallerID over the T1 modlue. The partner is using the T1 with E & M signalling (which I don't think can be changed), and whatever I tried didn't work. My only option right now is to get FXS ports on the Avaya side plugged into the

Ok, I have tested with almost all versions both in 2.3.2--*-stable and 2.3.3-*-beta - I am getting same messages: May 9 10:55:26 WARNING[3961]: chan_zap.c:1925 pri_find_dchan: No D-channels available! Using Primary on channel anyway 16! and same Down state pb01*CLI> pri show span 1 Primary D-channel: 16 Status: Provisioned, Down, Active Switchtype: EuroISDN Type: CPE Window Length: 0/7

I have a new Sangoma A102 and I'm trying to get it running in asterisk. A look through the dmesg log shows the card is detected and the various channels created. However, when I start asterisk I get the error below. Any ideas? My zapata.conf is below. Thanks, MD == Registered custom function SIPCHANINFO == Registered custom function CHECKSIPDOMAIN == Manager registered action

Hello to all, I have a problem with an asterisk qsig. I have three machines: Nortel CS1000 --- Card Sangoma PRI ---> Asterisk QSIG ---SIP Trunk---> Asterisk I use Snom phones on Asterisk. If I call from Asterisk to Nortel, Nortel reminds me of the name of the person i'm calling and I visualize on the display of Snom phone, but if I call from Nortel to Asterisk, the QSIG does not send