similar to: Sangoma card A101 Card troubles.

I upgraded from Tormenta2 to Sangoma A101. I followed the instructions, and installation was successful. zttool, ztcfg, all show card is installed properly. I copied the parameters from my old working zaptel.conf, zapata.conf and zapata-auto.conf. Verified on Sangoma website that these files are correct. Also configured wanpipe1.conf. But doing all this didn't start the PRI channels. It says

Im trying to install and configure sangoma ... every thing is OK but when type the command "wanrouter start" the following error apears: wan Driver not found. Thanks for any help

Hello, I am wondering if someone has got any ideas that can help solve this problem. I have a dial plan that you call into, and depending on certain conditions it calls out on a number grabbed from a database. Something like this : exten => s,n,Do something exten => s,n,Do something else exten => s,n,Dial(ZAP/g1/${OUTBOUND},${timeout}) I need to log the time the person

I have installed Asterisk on a CentOS4 box and then installed Asterisk from CVS. I installed a Sangoma A101 and connected it to a Adtran 600 using a T1 Crossover cable. The 600 has 12 x FXS, 12 x FXO interfaces. I ran through the wanpipe install instructions and configured it, now I can run [root@altpbx asterisk]# wanrouter hwprobe ------------------------------- | Wanpipe Hardware Probe Info

Hi, I have A101DE Sangoma Card( http://www.sangoma.com/products/hardware_products/digital_voice_and_data_networking/a101.html ) lspci shows as 03:04.0 Network controller: Sangoma Technologies Corp. A200/Remora FXO/FXS Analog AFT card [root at asterisk ~]# lspci -vvv -s 03:04.0 03:04.0 Network controller: Sangoma Technologies Corp. A200/Remora FXO/FXS Analog AFT card Subsystem: Unknown device

I have an issue that hopefully you can help me solve. I've got the sangoma a101 card and installed it on freebsd but I according to the manual I should be see when running dmesg PCi0 vendor..... something that tells me sangoma it's being recognized by the system. Now this is the 2nd card I try, the first one according to support was faulty and they sent me a new one. Is it possible to be

We are having an occasional one w-way audio problem that occurs about every 25 - 30 calls on a system configured as follows: Asterisk 1.2.12.1 Sangoma A101 w/wanpipe beta9 Polycom 500s w 1.5.3 This happens only on inbound calls from the PRI. The external caller can hear our customer answer and say hello, however, our customer cannot here their caller. Typically, the caller calls right back

Hi Everyone, We are using two Sangoma U100 (USB FXO) units connected to an Acer Aspire Revo (little PC running on Atom). The units work beautifully except for Monday :-) It maybe a conincedence or maybe the fact that Saturday/Sunday is off and something happens where one of these U100 modules goes into sleep and that's when all the 4 Dahdi channels are lost. So, I have been getting Monday

Hi All Just a quick check on the best way to ensure multiple cards/devices load in the correct order. Asterisk 1.8 with Sangoma A101 had no problems until we introduced an Astribank. root at pabx377:/etc/asterisk# dahdi_hardware -v usb:001/004 xpp_usb+ e4e4:1162 Astribank-modular FPGA-firmware LABEL=[usb:X1060395] CONNECTOR=@usb-0000:00:1d.7-3 XBUS-00/XPD-00:

I just got a brand new A101 and am trying to install it in my test Asterisk box. The install went without a hitch. I followed the directions on the Sangoma Wiki: Wanpipe Asterisk Install http://sangoma.editme.com/wanpipe-linux-asterisk-install Wanpipe for Asterisk Configuration http://sangoma.editme.com/wanpipe-asterisk-configure It went perfect, no problems and Asterisk came up fine. I downed

I am having a problem trying to get a Sangoma A101 to work with Unicall. I have installed the sangoma drivers and everything seems to be well but when I try to run ztcfg I get the following error: CAS signalling on span 1 conflicts with HDLC with FCS check on channel 16. Here is my /etc/zaptel.conf # MFC/R2 normalmente no usa CRC4 span=1,0,0,cas,hdb3 cas=1-15:1101 dchan=16 cas=17-31:1101

Hi Folks, I'm have Asterisk version 1.2.1 with a A101 PRI card. I'm working with the CLEC to bring up the PRI and inbound calls are hanging up at his end after a few seconds. I ran PRI debug but it only gives me minimal insight. " Ext: 1 Cause: Unknown (16), class = Normal Event (1)" He ran a trace and the only difference he is seeing is a "ISDN interface explicitly

Any benefit on getting the PCI Express version? Bill -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20070222/62f79910/attachment.htm

Skipped content of type multipart/alternative-------------- next part -------------- _______________________________________________ Asterisk-Dev mailing list Asterisk-Dev@lists.digium.com http://lists.digium.com/mailman/listinfo/asterisk-dev To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-dev

When I reload the asterisk I get the following warnings: Oct 13 08:29:17 WARNING[10170]: chan_zap.c:10874 setup_zap: Ignoring switchtype Oct 13 08:29:17 WARNING[10170]: chan_zap.c:10874 setup_zap: Ignoring signalling Oct 13 08:29:17 WARNING[10170]: chan_zap.c:10874 setup_zap: Ignoring rxwink Everything works fine as far as I know, I can dial and complete calls. So why am I getting this

Hi Since Im using the mISDN drivers and no zaptel stuff, I had to install ztdummy to get MeetMe to work. Well, that was the plan. Now, after getting the latest zaptel version over CVS (Im using Kernel 2.6), uncommenting all the modules except ztdummy in zaptel.sysconfig file and compiling this by "make", "make install" and "make linux26", I rebooted and

Hi everyone, I am reading through Sangoma Wiki right now. But someone may already and quickly notice this. I have a system that is down since the morning (maybe power intruptions). All seems fine except for "wanrouter status" shows disconnected. Following are the alarms raised. Should I call telco (they have long wait times) or should I just keep searching online for troubleshooting

When I reload the config, I see this error in the CLI. However, I don't see what I have done wrong: == Parsing '/etc/asterisk/zapata.conf': Found May 30 16:38:42 WARNING[12630]: chan_zap.c:10088 setup_zap: Ignoring signalling -- Reconfigured channel 1, FXO Kewlstart signalling May 30 16:38:42 WARNING[12630]: chan_zap.c:10088 setup_zap: Ignoring signalling -- Reconfigured

Good day all We got a Wildcard TE110P I installed linux,zaptel,libpti and asterisk I coped over my zaptel.conf and zapata.conf from a previous E100P config But when I try to start asterisk it gives error not bying able to load zap channles: == Parsing '/etc/asterisk/zapata.conf': Found Jan 10 08:17:18 WARNING[-1084595552]: chan_zap.c:9308 setup_zap: Ignoring switchtype Jan 10 08:17:18

I reloaded my asterisk and found some red lines flushing by. When I stopped it I see: WARNING[21481]: cahn_zap.c:9773 setup_zap: Ignoring signalling WARNING[21481]: cahn_zap.c:9773 setup_zap: Ignoring echocancelwhenbridge WARNING[21481]: cahn_zap.c:9773 setup_zap: Ignoring echotraining Reconfigure channel 1, FXO Kewlstart signalling Reconfigure channel 2, FXO Kewlstart signalling