Displaying 20 results from an estimated 2000 matches similar to: "Very bad quality with AVM Fritz!card PCI and chan_capi"
2006 Jun 19
2
Asterisk voicemail problem with isdn avm fritz!card
Hello everyone,
I have Asterisk SVN-trunk-r7498 installed on a server (celeron 2.4 Ghz,
256MB) with a TDM40b a TDM04b and an avm fritz!card pci.
I experience a problem with voicemail: my messages are good unless the
incoming call comes from isdn, which means via the avm fritz!card. In
this case (and in this case only) the message is disjointed and I can
hear at most 1 second out of a 1 minute
2004 Feb 17
5
chan_capi problem
Hi to all
I've mada up my mind and i tried to change from i4l to chan_capi, following some councelling from the gurus.
I compiled it up, and when i try to load it in modules.conf, i get that wonderful message and Asterisk does not start:
[chan_capi.so]Feb 17 09:21:40 WARNING[16384]: loader.c:239 ast_load_resource: /usr/lib/asterisk/modules/chan_capi.so: undefined symbol: ast_get_group
Feb
2005 Sep 28
2
chan_capi-cm, Euro ISDN bus: 2 extensions on same BRI port not working
Hello,
I am using a system with an AVM ISDN PCI card (fcpci) and asterisk with
chan_capi-cm-0.6. The hardware is connected to a Siemens Hipath 3550 PBX. As
a BRI connection has 2 channels and allows 2 simultaneous calls,
numbers/MSNs 6391 and 6392 were for provisioned for each channel. The system
is working (partly, read on), the trick is the correct cable wiring and
setup the PBX's port
2007 Nov 26
3
Problems getting Asterisk to detect call in SUSE9.3, with FritzCard
I have installed an Asterisk 1.4 on Suse93 using a FritzCard.
Some calls are logged to the ISDN log, but Asterisk is not detecting
incoming calls.
I wonder whether some other device or process is preventing Asterisk
from gaining access to the isdn line?
Is there some way to ensure that only Asterisk can listening to the
line, or get it to share the line with some other device, such as the
fax
2006 Jan 20
2
AVM C4, asterisk-1.0.8, /etc/asterisk/capi.conf
Has anyone a working /etc/asterisk/capi.conf example for Germany or
Switzerland using the AVM C4 - ISDN Card.
I try to connect asterisk to 3 wires BRI-ISDN (Swisscom).
I appreciate your help and it would save me a lot of time, figuring
it out by myself.
regards, Claudio
2004 Jul 08
3
ISDN, AVM C4, HFC-cards and echo
Hello,
I've been using * for quite a while using AVM C4 card and a few
Grandstream Budgetone 102 hard phones plus couple of HandyTone 286.
Echo is a big problem. I am getting used to it, but some users complain.
Anyone has experience w/ regards to echo comparing the AVM C4 with two
HFC-cards? Before shelling out time and money, maybe someone else
already has done so, and could tell me if
2006 Jun 29
1
Very bad quality with AVM Fritz!card PCI andchan_capi
> > That is possible, how could I check that?
> > I can see that IRQ 17 is shared between eth0 and my fritz!card
> but I
> > don't know if it changes anything:
>
> Can you try it (or eth0) in a different slot (or change IRQ's in the
> BIOS if possible) to see if it makes any difference? That's the
> only way
> to know for sure, anything else is
2004 Apr 29
1
CAPI ptp does not work
Hallo all,
I am trying to get * with chan_capi and a ptp-ISDN with 4 lines on a AVM C4
card to work.
But weather inbound nor outbound is working :(
My capi.conf:
;
; CAPI config
;
;
[general]
nationalprefix=0
internationalprefix=00
rxgain=0.8
txgain=0.8
[interfaces]
mode=immediate
isdnmode=ptp
msn=8993
incomingmsn=*
mode=immediate
controller=1,2,3,4
softdtmf=1
;accountcode=
context=demo
2003 Dec 23
2
Capi Dial & outgoing msn?
Hi all,
I am trying to get Capi Dial to use a specific outgoing msn. I can't get
it to work. If I make a test call to 0703241494 (same isdn line, just
one of the other numbers) I don't get CLID at all. Any ideas?
; use 0703241432 as outgoing msn
exten => _070.,1,Dial(CAPI/@0703241432:${EXTEN}|30|r)
in capi.conf I have:
[general]
nationalprefix=0
internationalprefix=00
rxgain=0.8
2005 Sep 29
1
chan_cap-cm-0.6 is not working for incomming calls
Hi,
I tried to use the version 0.6 of chan_capi-cm for outgoing calls it
works perfectly but for incoming calls it will not work:
--- snip ---
*CLI> capi debug
CAPI Debugging Enabled
-- CONNECT_IND
(PLCI=0x101,DID=97,CID=0179903xxxx,CIP=0x1,CONTROLLER=0x1)
== reventix: Incoming call '0179903xxxx' -> '97'
-- reventix: info element CALLED PARTY NUMBER
--
2005 Feb 21
1
Problem with ISDN Dialin via CAPI
Hello List,
because this is my first post to this list, i'd like to introduce myself.
My name is Thorsten M?ller, 26 years old and live near Frankfurt/Main in
germany.
Okay, now to the reason for this posting:
I just installed my first asterisk server (Debian 2.2 Kernel 2.4.18-686)
with AVM ISDN Fritz PCI card (passive).
I followed the configuration on http://voip-info.org and the
2004 May 31
1
Chan Capi Audio Quality Issue...
Hello all,
I've just finished to install chan_capi with 3 AVM Fritz PCI cards.
It correctly loads the 3 drivers, and * starts without errors.
immediately after * start, audio quality is really fine, but, after the
first incoming call, all incoming audio is broken, trembling and stuttering.
2006 Feb 23
1
chan_capi-cm 0.6.4 random outgoing MSN problem
I've having a big problem after having upgraded to 1.2.4 and
chan_capi-cm 0.6.4
When making outgoing calls I don't seem to have any control over the CLI
that is presented to the called party -- it can be any one of the MSNs
allocated to the line, allocated on what seems to be a random basis.
This is on a BT Business Highway line (which is essentially an ISDN2e
line with two built-in
2005 Jul 13
2
Anyone signed up with Galaxyvoice lateley?
One of my buddies signed up with GV yesterday with a view to using them
on his * server. Problem is that the settings they gave him don't work
with asterisk. They do however work with X-Lite.
Any ideas? He's using the settings outlined on my web page.
Mark
--
Mark, G7LTT/KC2ENI
Randolph, NJ
http://www.g7ltt.com
2006 Mar 15
1
AVM C2 chan_capi-cm-0.6.3 Error on Dial
I'm getting a strange error on one of the two controllers on an AVM C2
card under chan_capi-cm-0.6.3.
I have two ISDN controllers defined, both in the same group, both
connections are UK ISDN2e Point to Point:
On the third outbound call (both of the first two calls are handled by
the second controller "ISDN2",) I get this error :
chan_capi.c conf_error 0x2001 PLCI=0x301
2005 Aug 27
1
Asterisk ISDN: Problem Setting CallerID as DID Extension Numbers.
Hello Group,
Current Setup:
- Eicon Quad BRI ISDN Card.
- 4 ISDN BRI (Telco: Telstra) Onramp2 services.
- Mode: Point2Point.
- 100 Indial Number ranges. Full National Number (9 digit format): BAAAAAAXX
where: B (Area code): 2/3/7/8
A (Normal Numbers)
X (99 Indial extensions)
eg: BAAAAAA00
BAAAAAA20 etc
Requirement:
- To be able send Indial numbers as Caller ID when dialing out.
Configration:
2004 Dec 17
1
chan_capi - avm card does not work
Hi,
I added a Fritz!PCI card to my asterisk system which is running on fc2
!.
I installed the avm modules (fcpci) and when i try an capiinit and a
capiinfo then everything seems to be OK (you can see capiinfo and lsmod
at the end of the text) !.
I installed the asterisk chan_capi module and when i start asterisk and
enter the command capi info on the command line i get back:
*CLI> capi info
2007 Nov 29
0
[Copfilter] Copy of quarantined email - *** SPAM *** [6.6/6.0] Problems getting Asterisk to detect call in
I have installed an Asterisk 1.4 on Suse93 using a FritzCard.
Some calls are logged to the ISDN log, but Asterisk is not detecting
incoming calls.
I wonder whether some other device or process is preventing Asterisk
from gaining access to the isdn line?
Is there some way to ensure that only Asterisk can listening to the
line, or get it to share the line with some other device, such as the
fax
2007 Mar 22
1
chan_capi and only one B channel usable?
Hello list!
I have a Asterisk 1.2.10 running using the package from Backports.org
for Debian Sarge.
I have setup chan_capi (0.6.5 from Backports) and it seems that I am
only able to use on B-Channel.
When trying to place the second call I get:
CAPI INFO 0x34a2: No circuit / channel available
capi info shows:
Contr1: 2 B channels total, 1 B channels free
And capi.conf is:
[ISDN1]
2004 Apr 28
4
Mysql Confusion..
Ok I know this may have been covered and I did have a look back in the
archives but didn't find anthing so I am asking it now..
Many moons ago the MySQL CDR functions and MySQL Voicemail functions had
to be removed from the main asterisk code because of licensing issues..
Now there is new MySQL stuff like MySQL FRIENDS for SIP and IAX
definitions..
So how is it that these options