similar to: isdn and PARK

Hi List, I?m having problems compiling chan_misdn: asterisk:/usr/src/chan_misdn-beta-0.0.3-rc4 # make install cc -ggdb -Wall -D_GNU_SOURCE -Wno-missing-prototypes -Wno-missing-declarations -fPIC -I/usr/src/asterisk/include -DAST_CONFIG_DIR=\"/etc/asterisk/\" -I/usr/src/mISDNuser/include -I/usr/src/linux-2.6/include -I/usr/src/mISDNuser/i4lnet/ -Wall -c -o chan_misdn.o chan_misdn.c

Hello, After upgrading my kernel to mISDN-1.1.1 while keeping asterisk-1.2.16 I no longer match any extension. Apparently the "dad" is empty. However I can see the number just before it (146472130): P[ 4] I IND :SETUP oad:!?145201798p ?146472130 dad: ?146472130 pid:2 state:none P[ 4] EXPORT_PID: pid:2 Mar 23 09:35:28 WARNING[6725]: chan_misdn.c:4750 chan_misdn_log: Extension can

hi i've configured a Beronet BN8S0 Card with misdn beronet utility. the card is configured with all lines in TE and P2P mode, and it is connected with the special cable with an ISDN connection. i've turned on debugging to level 4, this is the output from the asterisk cli when i receive a call: P[ 5] MGMT: Short status dinfo 1000001 P[ 5] MGMT: SSTATUS: L1_ACTIVATED P[ 5] handle_frm:

Hi, I have a Digium B410P 4-port BRI card. I installed misdn 1.1.3 with hfcmulti driver and misdnuser 1.1.3. I configured the card "correctly" as misdnportinfo reports: # misdnportinfo Port 1: TE-mode BRI S/T interface line (for phone lines) -> Interface is Poin-To-Point. -> Protocol: DSS1 (Euro ISDN) -> childcnt: 2 -------- Port 2: TE-mode BRI S/T interface line (for

Hi all, Does anybody of you have the winbond w6692 working with the mISDN/chan_misdn.so? When loading chan_misdn.so from Asterisk, I get a "No lower Id port:1" error. The /var/log/messages file says: "MISDN free_device: entitylist not empty" I'm using Linux 2.6.11.11 + mISDN-CVS-2005-05-01 + Asterisk 1.0.7 + Zaptel 1.0.7 chan_misdn build from chan_misdn-beta-0.0.3-rc6

What are the advantages in using mISDN over other solutions? If I knew why it was a good idea (like does it have better sound quality than alternatives?) then I would put the time in to test it, and also improve the Wiki. -----Original Message----- From: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com] On Behalf Of Thomas H?ger Sent: Friday, January 21,

Hi everyone, I was trying to mode the following exercise using R. The question: Set up a one pool model using numericintegration. The model will run from time 1 to time 30 using a time step of 1.The pool (A) will be fed by flux "inA" at a rate of 5 units per hour anddrained by flux "outA" at a rate of 20% per hour. At time 0, A has 5units. At time 30, what is the pool size of

Hello ! I would like to get working a Fritz PCI card using chan_misdn operating in ptp mode. Afer compiling mISDN into the kernel and building chan_misdn Asterisk stops loading with : [chan_misdn.so] => (Channel driver for mISDN Support (Bri/Pri)) == Parsing '/etc/asterisk/misdn.conf': Found UnLocking config_mutex == Registered channel type 'mISDN' (This driver enables

Has anyone got chan_misdn working with passive BRI cards yet? I've tried both hfc (hfcpci.ko) and w6692 (w6692pci.ko) cards, but when I start asterisk I get the following when chan_misdn is loaded: [chan_misdn.so] => (Channel driver for mISDN Support (Bri/Pri)) == Parsing '/etc/asterisk/misdn.conf': Found == Registered channel type 'mISDN' (This driver enables the

Hello, I'm evaluating to possibility to use chan_misdn as a short term workaround, in case latest Dahdi is not stable enough for what we are planning to do (we wish to use Junghanns and Digium BRI hardware with Asterisk 1.6) . I've read www.mISDN.org but still have a couple of questions : 1. Is correct that in a 2.6.27 (and up) enabled kernel, the "embedded" mISDN version is

Hi all! I'm getting an error when I try to start asterisk with chan_misdn. I patched my kernel (2.6.12.4), and compiled the whole stuff (kernel, mISDNuser, asterisk, chan_misdn). I got mISDN from http://isdn.jolly.de/download/v3.0/ I'm using a CVS Snapshot of asterisk, which was checked out about 5 hours ago. This is the error: [chan_misdn.so]Aug 15 14:13:29 WARNING[4929]:

Hi i am experiencing some problem with asterisk and misdn i've patched and recompiled the 2.6.15.5 kernel on the server i use a BN8S0 card with alla channels in TE mode. i can load hfcmulti and mISDN_dsp i load this with: /sbin/modprobe hfcmulti layermask=0xf protocol=0x22 type=0x08 and then /sbin/modprobe mISDN_dsp dmesg returns me the following: Modular ISDN Stack core $Revision: 1.34

Hallo all, i have a problem on loading chan_misdn. The misdn is running and all cards (TDM40B+AVMFritz) is initialized. When im going to start asterisk with the chan_misdn.so module i get the following error in the log (on console) and asterisk ist hanging. i use the current CVS-HEAD of asterisk (7 Days old), chan_misdn-0.2.1-rc2 and mISDN+mISDNuser from the automated installation. Is here

Hi there, we've announced a new release of our chan_misdn channel driver. chan_misdn is a GPL channel driver for the new Linux ISDN-Layer mISDN (www.isdn4linux.org). So you can use all from mISDN supported ISDN catds in Asterisk. Feel free to donwload and test it at : http://www.beronet.com/download/chan_misdn-beta-0.0.3-rc4.tgz You can report bugs and feature requests to

Hi there, we've announced a new release of our chan_misdn channel driver. chan_misdn is a GPL channel driver for the new Linux ISDN-Layer mISDN (www.isdn4linux.org). So you can use all from mISDN supported ISDN catds in Asterisk. Feel free to donwload and test it at : http://www.beronet.com/download/chan_misdn-beta-0.0.3-rc5.tgz You can report bugs and feature requests to

Hi. I'm having problems with chan_mISDN configuration. Line "echotraining=yes" causes warning, when Asterisk is parsing misdn.conf and I'm confused why the PBX doesn't accept the setting. No matter which section I try to offer it, it is always invalid or out of range. The setting itself is supposed to be valid, it is in the sample configuration file of chan_mISDN 0.3.1.

So far i've grasped that to use a card in NT mode it should have layermask=3 as module option. Is it the only thing that sets TE or NT mode for card? Perhaps there are settings in misdn.conf ? I can only get the card to work in TE mode and even then when asterisk is ran as asterisk -vvvgc it exits right after chan_misdn is loaded with theese messages: [chan_misdn.so] => (Channel driver

Could someone please comment on the current state of chan_capi, chan_misdn and chan_modem channel drivers in terms of functionality and stability. Specifically, which channel driver would be best for a passive PCI HFC or W6692 ISDN card. The chan_misdn wiki claims that chan_capi distinguishes between junghanns and non-junghans cards, and that chan_misdn is better suited for general misdn

Hi For use my isdn card in NT mode I have compiled chan_misdn. When I launch asterisk it stop with th e message : [chan_misdn.so] => (Channel driver for mISDN Support (Bri/Pri)) == Parsing '/etc/asterisk/misdn.conf': Found UnLocking config_mutex == Registered channel type 'mISDN' (This driver enables the asterisk to use hardware which is supported by the new ) Locking

I'm running a setup with chan_misdn on a austrian PTP-line. When somebody dials in without an extension, he gets a busy signal. I don't see the call at all in asterisk. I *have* set immediate=yes in misdn.conf. And I *do* have an s-extension in my dialplan for the context used by misdn. Calls that provide an extension work fine. Attached is my misdn.conf and a verbose 3, misdn set debug