similar to: 100 lines PBX + system config - repost

hi building a new setup, we want to try using sangoma cards. can these be used as time sources the same way as TE410Ps? thanks roy

Hi guys, Can I use a Sangoma a101 to interface a legacy pbx to an Asterisk server? The pbx doesn't have sip and I want to come in off of a sip trunk and interface with the older system. I know I can use a pri card to hook in to the phone network, but can I use this same card to feed back the signaling as if I were the phone company to the older system? Thanks, Tom

Good day all Is there someone that's got asterisk working well with a A101/E1 card Apparently they don't have RBS support? Please advice Thanks Altus

I have upgraded the GXP-2000 to the newest firmware 1.0.1.12<http://1.0.1.12>and the phone is much more usable However, I still have two slight sound quality issues: 1) There is static on the line at all times. It is not that noticable to me, but when I make calls out the PSTN the person on the other end hears it. If I use a Cisco ATA with an analog phone and call the same person again

Hi, I'm looking to stream a large amount of conncurrent connects and want to use icecast probably on a CentOS base. The bandwidth requirements are over 60 Mbps before any overheads, I'm looking at using some Dell SC1425 machines but am not sure how many I'd need, I'd appreciated hearing your experiences and suggestions. I need to be able to stream the following simultaneous

Hi, I've just installed R 2.10.1 for linux, and html help has not been built (just the index page of each package but not the documentation for the individual functions in the packages. I cannot see any flag in the ./configure to set if html is going to be build. Please could you tell me what should I do to biuld html files? Thanks and best regards, Javier ---

Has anyone been able to get the IP501 to discover the FTP server IP address (via dhcp or dns) and download 100% of the config from a provisioning server? We are still having to touch each unit to enter the ftp server address and password, as well as set many of the options that will not take from the config file. Have a sample config file you are willing to share? What is required in

Hi, everyone, We've been reasonably happy with Polycom SoundPoint phones, but we only have them installed on the LAN. I've read that they have problems working across NAT. So ... I guess I have a few questions. First, is there a way to get Polycoms to work well over NAT? If not, then are there phones of comparable voice quality that do work well over NAT? Without costing a lot more?

Hi, what new Dell servers are compatible and KNOWN to work with Digium TDM cards? I've looked at Digium's compatibility list at http://www.digium.com/index.php?menu=compatibility. Does this mean that other Dell servers like SC1420, SC1425, 800, 1800 are working just fine with TDM cards? Can someone clarify this? Thanks -David

Hi All - I noticed that the Polycom IP501's are now shipping. Has anyone gotten one yet, and if so, what's different about the phone? Any UI improvements, or is it just better hardware? Thanks, Noah

Hi Developer, In my processor I am not using registers so I wrote Simple register.td file with bare minimum functions. But when I am registering my target with llvm it is showing "*Segmentation Fault(core dumped)*" Error and also same error while generating table-gen for asm-writer. Some one told comment out EditRegesterName function. because this error is due to EditRegisterName it

Greetings folks- I'm experiencing issues with a freshly installed box. When a call comes in via PRI (Sangoma AFT-A104), I see this in my logs: [Dec 15 14:26:10] WARNING[23546] chan_dahdi.c: Unable to enable echo cancellation on channel 12 (Invalid argument) [Dec 15 14:26:10] WARNING[23546] chan_dahdi.c: Unable to enable echo cancellation on channel 8 (Invalid argument) [Dec 15 14:26:10]

Hi, 1. I have 2 panes, each having approximately 45-50 slides, all the slide images are 110x82 pixels in size, enclosed in their respective div''s. 2. These divs are further enclosed in a parent div, which is defined as a Sortable on page load. 3. There is a destination div on the RHS also. Sortable.create("div_leftDiv", {ghosting:true, revert: true, dropOnEmpty:true,

Hi Developers, I have written C program and want to generate IR file for Specific Target I have tried with following command but got a error as follows, COMMAND: *clang -S -emit-llvm -march=leg ~/llc-test-examples/ex9.c -o ~/llc-test-examples/ex9.ll* ERROR: *error: unknown target CPU 'leg'* So any please help me what all other step should I do previously to get my *leg* target in clang.

Hello, I would like to convert an objects list such as objects() or ls() that outputs "a101" "a102" "a104" "a107" "a109" to read within a list statement as follows : list(a101,a102,a104,a107,a109) Thanks Tony

Hello, Are there any issues with Centos 4.4 and asterisk. Thanks in advance Varun

By default the prototype.js gives us the function /* prevent memory leaks in IE */ Event.observe(window, ''unload'', Event.unloadCache, false); But there is no unload event in out application as the content of the div keeps changing using the Ajax.Updater function. To handle such a scenario, we''ve added the following lines of code to prototype.js /* prevent

Wondering if anyone has experienced an intermittent one way audio (called party can not hear) problem in these conditions; Several IP501 phones local, same subnet. Remote asterisk No NAT anywhere Polycom IP501 ulaw only, canreinvite=yes Asterisk Call termination path is to a sonus GSX operated by the upstream carrier, ulaw only, canreinvite=no The idea is that if the Polycoms are

Hai, The steps shown here dont work? https://wiki.samba.org/index.php/Demoting_a_Samba_AD_DC If that is the case and you besides that free of errors. Then upgrade, and try again once your on at least samba 4.9 or 4.10. As im hoping you are upgrade straight to Buster. Greetz, Louis > -----Oorspronkelijk bericht----- > Van: samba [mailto:samba-bounces at lists.samba.org] Namens

Hi Andrew, I think I diluted my question. My question was not related to MCJIT. I ran the following 4 scenarios: (1)gcc -mcpu=corei7 tetris.c -o tetris (2)gcc -mcpu=athlon64 tetris.c -o tetris (3)clang -march=corei7 tetris.c -o tetris (4)clang -march=athlon64 tetris.c -o tetris In (1) and (2), I see difference in order of instructions in the output binaries, which I expected because every CPU