similar to: Asterisk + Linksys PAP2-NA / Call Clearing

Hello everyone - first time poster, long time lurker. (sounds like a radio morning program, I know). I'm attempting to get my InterTel Axxess (w/v9.0 software) to play nice with my Asterisk implementation. Asterisk 1.2.6 is running on a Fedora Core 4 x86 box. I've tried getting the Axxess to talk SIP to Asterisk, but InterTel's SIP implementation is, well-let's say, incomplete.

Hello - I have (finally) obtained a fair amount of success in connecting my Intertel Axxess PBX to an asterisk box via a T1 PRI. I can place calls from the Intertel side through the T1, out to an IAX2 softphone and the calls get routed correctly and all of the CID information stays intact. However, when I call from the IAX side to an extension which should route back through to the Intertel

Hi all, My office recently purchased an InterTel Axxess system with the IPRC card for VoIP. To our suprise, this card allows the InterTel endpoints and MGCP endpoints to work, but not SIP clients. I was really expecting to get a SIP softphone working with this setup, but that appears to require our vendor to sell us a SIP gateway and licenses at a not yet determined price. With this

Hi, I have 3 PAP2 connected to *, they work fine but there are some things which I would like to improve, some of them are: - double ring tone when placing a call (I hear two tones it seems like the PAP2 is generating it's own tone) - some kind of noise (like glitches or something) when I pick up the phone (seems like some polarity thing) - I'd like to keep the tone after

The best I can do so far (which appears to be a bit of a hack) is (<:0>S0), which says to add a '0' to the start of the string and dial immediately. This gives asterisk an extension dialled of '0', which isn't the 's' that i'd hoped for, but is a good start! (S0) by itself doesn't work, nor does (<:>S0). Any other suggestions? Thanks James >

Is there a way to configure the linksys pap2 to automatically connect to asterisk on lifting the handset (presumably into the 's' state)? Asterisk would then be listening for DTMF tones to figure out what to do rather than having to put a dial plan into each pap2. I think the pap2 is pretty much the same inside as a few of the sipura boxes so the same thing might work if anyone knows...

I am using my first PAP2 device from linksys. Used many polycom phones... I configured the PAP2 device with asterisk. I have the registration, thought I was good to go. Plugged in my Valcom 2924 public address analog connection, called the extension and I got busy... very strange I thought. I then looked at the status page of the PAP2 and it says the following Reg online and hook state OFF.

>Message: 7 >Date: Sun, 29 Oct 2006 22:00:22 +0100 >From: "Jose Limeres" <jlimeres@gmail.com> >Subject: [asterisk-users] Linksys PAP2: calling tone stops after 5 > tones >To: asterisk-users@lists.digium.com >Message-ID: > <2b3431b20610291300u420116e5scf9103d7dac54321@mail.gmail.com> >Content-Type: text/plain; charset=ISO-8859-1; format=flowed >

Greetings all - I'm interested in using an asterisk box to supplement and add VoIP capabilities to our legacy InterTel Axxess PBX. After searching through the list archives and through google, it seems that the best way to go about this is to connect the two systems via a T1. Is this correct? The PBX currently doesn't have any VoIP capabilities, so that's not an option for

I've got a Linksys PAP2 on my Vonage account with unlimited usage, but my softphone-addon account only has 500 minutes. Anyone ever try to setup their * to mimick the Linksys PAP2 ? Any comments or suggestions on what problems I might run into if I try? -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hi all, I have a problem with the dialing tone in PAP2: When making a call, I can hear the calling tone 5 times and then it stops. The called party still hears the call but not the calling party. I've playing around with different parameters on the PAP2 web config with no success until now. Anyone has seen the same probelm? Thanks, Jose

Hi, anyone can confirm if the Linksys's ATA and Router (PAP2-NA and RT31P2-NA) have the same limitation of just one G.729 call like the Cisco ATA 186 ? I'm testing both appliances here and found this issue but could not confirm this anywhere (nothing on the manual, no document or post from any user about this). In my tests they use G.729 only on the first call and G.711 on the

I had just found a Dlink DVG-1120 on ebay and I'm curious if anyone has used you it with asterisk. They were only $65. I have tested with the Linksys Pap2 and found that box to be fairly nice except for a lot of backgound/white noise. I was wondering if any else had experienced that? Let me know if I've wasted $65 on the Dlink and also if you had similar experience with white noise on

Hi everybody, Well, I've finally got asterisk to to talk nicely with my Intertel pbx. Currently there is a outside T1 line (e&m wink start, esf, b8zs) connected to asterisk, and then asterisk connected similarly to my Intertel pbx. For right now all asterisk is doing is passing calls between the two. When I call out from the pbx, I can connect perfectly to the outside world. When I

Has anybody else experienced problems with the Linksys PAP2-NA's? I've now had two of them fail unexpectedly, with no apparent rhyme or reason, having gone into a RED power LED, with a solid blue ethernet LED. No response from the device either on the network or from the phone.... To make matters even crazier, the one that now failed was the one I received as a replacement for the

Hi, I have a Linksys PAP2-NA connectd to my asterisk. I would like the device to add 2 characters in front of the dialled number always when it send the call to my asterisk. I dont know how to do that. I will summarise my requirement. My friend dials 1-210-1234345, i want the asterisk to get 55-1-210-1234345. Can someone help me to add this dialplan. Thanks in advance Dan -------------- next

Hi! Can I use my Linksys PAP2 with asterisk and an analog CLIP phone to show the Caller number on the phone. There's a "Caller ID Method:" option on Regional settings, but I tested all options, and my CLIP phone never shows the Caller number... :( Any idea?

I have a PAP2 with 2 phone ports. When I call them everything works fine until I hung up the call. There is about 30-40 seconds until I can call to that extension again. Before that it gives me busy messages. Extension config: exten => 199,1,Dial(SIP/199,30) exten => 199,102,Hangup Any suggestions? Thanks

My asterisk box doesn't recognize DTMF from my analog phone, plugged into my ATA(linksys pap2 version2). I can make/receive calls fine... it's just that, for example, I cannot login to my asterisk voicemail. Softphones (such as x-lite) are fine. I've turned up a few articles via google where some people have this trouble, but have not seen suggestions on how to fix. I presume

Hullo :) Can someone help me untangle a bit of a mess? I'm trying to set up a demo * server to show off how useful it can be to our business (as an IVR system and VoIP backup if our ISDN30s fail). I've not been able to get NT mode working with our InterTel Axxess PBX, so I've resorted to using normal TE mode and working on the basis the people dial one of the ISDN BRI extension