similar to: BN8S0 Installation problem - 0 devices registrered

I'm using avm fritz card usb with kernel 2.6 patch with mISDN. The module is load correctly when I type lsmod I've got the following output: Module Size Used by zaptel 178308 0 avmfritz 21388 0 mISDN_isac 14336 1 avmfritz mISDN_dsp 191424 0 l3udss1 34184 0 mISDN_l2 39040 0

Hi, I have done my best and tired of searching the net about the problem. If anybody could help would be a great favour. Description of Problem ------------------------ I am trying to install two Netpci cards(Traverse Technology Netjet ISDN-s) on Trixbox 2 and aim is to use in Asterisk as dailin and dialout. I compliled the driver as directed in the manufacture manual. After installation dmesg

Hi i am experiencing some problem with asterisk and misdn i've patched and recompiled the 2.6.15.5 kernel on the server i use a BN8S0 card with alla channels in TE mode. i can load hfcmulti and mISDN_dsp i load this with: /sbin/modprobe hfcmulti layermask=0xf protocol=0x22 type=0x08 and then /sbin/modprobe mISDN_dsp dmesg returns me the following: Modular ISDN Stack core $Revision: 1.34

Hi list, I installed a fresh Debian/Etch with Asterisk 1.4 and Zaptel 1.4 from SVN for 2 Digium B410P card. I ran configure in Asterisk dir, went in zaptel dir and: make, make install, make b410p. Everything is ok. Now I want to compile Asterisk but can't activate the chan_misdn channel which depends on -from menuselect- isdnnet(E), misdn(E), suppserv(E) When I made the make b410p, all

Hi, a few month ago, I tried to install zaptel for my Beronet BN8S0 pci card... I gave up and took hfcmulti/lcr. Now dahdi (2.2.1.1) seems to support the card and I'm very interested to get it to work. But how to get rid of these annoying qozap driver? bishop dahdi # lspci -v -nn -s 01:00.0 01:00.0 ISDN controller [0204]: Cologne Chip Designs GmbH ISDN network Controller [HFC-8S]

Hi all, we're buildin an Asterisk box based on an Intel IXP425 board. The board uses a Beronet BN2S0 ISDN card, mISDN 1.1.4 and asterisk 1.4.2. hfc_multi has been patched to compile under big endian cpu, and so also capi kernel files. All the modules seem to load correctly (configuration was made with misdn-init config), but when starting cha_misdn, asterisk outputs the following lines: P[ 1]

Hi all, Does anybody of you have the winbond w6692 working with the mISDN/chan_misdn.so? When loading chan_misdn.so from Asterisk, I get a "No lower Id port:1" error. The /var/log/messages file says: "MISDN free_device: entitylist not empty" I'm using Linux 2.6.11.11 + mISDN-CVS-2005-05-01 + Asterisk 1.0.7 + Zaptel 1.0.7 chan_misdn build from chan_misdn-beta-0.0.3-rc6

Hello all, I'm trying to setup a AVM C2 card. I have read the kernel requirements for this card. <M> CAPI2.0 support [*] Verbose reason code reporting (Kernel size +=7K) [*] CAPI2.0 Middleware support (EXPERIMENTAL) <M> CAPI2.0 /dev/capi support [*] CAPI2.0 filesystem support <M> CAPI2.0 capidrv interface support My problem is when I make a "make

Hi i've installed this software: ******************** SOFTWARE mISDN-1_1_7 mISDNuser-1_1_7 Asterisk-1.4.15 ******************** SOFTWARE misdn is correctly loaded by misdn-inist start Here there is the misdn.conf (copied from an existing and working installation with Asterisk 1.2.x and one BN8S0) ******************** MISDN.CONF [general] misdn_init=/etc/misdn-init.conf debug=0 bridging=no

Hi, I have installed Asterisk 1.4 with mISDN with the install-asterisk.tar.gz script from beronet.com. On my system I have two cards, one a AVM Frit!Card Pci 2.0 and one HFC-S chip. I know both to work well with mISDN on my system from a previous installation. Now however, the AVM card works well at first glance, i.e. it "registers" incoming calls and works through the asterisk

Hi. I'm having problems with chan_mISDN configuration. Line "echotraining=yes" causes warning, when Asterisk is parsing misdn.conf and I'm confused why the PBX doesn't accept the setting. No matter which section I try to offer it, it is always invalid or out of range. The setting itself is supposed to be valid, it is in the sample configuration file of chan_mISDN 0.3.1.

Good Evening, The company I work for is attempting to connect an Cisco ISDN Router to an OpenVOX B200P BRI Card so that we can get it to dial out across an existing ISDN PRI Line also installed in the Asterisk PBX Everything has compiled successfully and the BRI card has been detected when mISDN is started: # misdnportinfo Port 1: NT-mode BRI S/T interface port (for phones) -> Interface

Your Zap conf files would be helpful. Zttest results? Cat /proc/interrupts. Sharing interrupts? Any funky error in the logs? Thanks, Steve Totaro http://www.asteriskhelpdesk.com > -----Original Message----- > From: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users- > bounces@lists.digium.com] On Behalf Of Administrator TOOTAI > Sent: Thursday, May 10, 2007 6:24 AM

Hi, I'm installing Asterisk on Ubuntu 6.10 When I first compiled the zaptel package I used: make clean make make install So far so good, but the following command failed: make b410p I did some digging on google and found a guide on how to install it manually, but the result was the same. I got these files ftp.digium.com/pub/telephony/zaptel/b410p/misdn-b410p.tar.gz

Hi, I have a Digium B410P 4-port BRI card. I installed misdn 1.1.3 with hfcmulti driver and misdnuser 1.1.3. I configured the card "correctly" as misdnportinfo reports: # misdnportinfo Port 1: TE-mode BRI S/T interface line (for phone lines) -> Interface is Poin-To-Point. -> Protocol: DSS1 (Euro ISDN) -> childcnt: 2 -------- Port 2: TE-mode BRI S/T interface line (for

HI, I tried to install asterisk and mISDN via http://www.asterisk.org/downloads/yum My machine is running with kernel-2.6.18-164.15.1.el5.i686 # grep kernel /var/log/yum.log Mar 21 16:09:28 Installed: kernel-2.6.18-164.15.1.el5.i686 Mar 21 16:09:42 Installed: kernel-devel-2.6.18-164.15.1.el5.i686 I've installed the following packages: # yum install asterisk16-misdn mISDN mISDNuser

Hello, list a have a problem i can start asterisk, i get the fowlling error: [chan_capi.so] => (Common ISDN API for Asterisk) == Parsing '/etc/asterisk/capi.conf': Found Feb 11 13:50:36 NOTICE[2535]: chan_capi.c:2636 load_module: CAPI not installed! Feb 11 13:50:36 WARNING[2535]: loader.c:345 ast_load_resource: chan_capi.so: load_module failed, returning -1 Feb 11 13:50:36

Hi, has andybody a running capi2.0 application like fritz with wine? I tried to use the capri-client for windoze, but I have no idea how to load ghost.exe before starting fritz. Thanks, Eckhard

hi i've configured a Beronet BN8S0 Card with misdn beronet utility. the card is configured with all lines in TE and P2P mode, and it is connected with the special cable with an ISDN connection. i've turned on debugging to level 4, this is the output from the asterisk cli when i receive a call: P[ 5] MGMT: Short status dinfo 1000001 P[ 5] MGMT: SSTATUS: L1_ACTIVATED P[ 5] handle_frm:

Its been a few days, I was wondering if anyone else has any ideas on how to get this to work? If not, could I ask a the direct question as to if anyone here has (or knows someone who has) successfully got something like a Cisco Router to successfully establish an ISDN data/Internet connection through the Asterisk PBX?