similar to: Openion on Sipura SPA-2100

I want to implement a one way announcement and paging facility using Asterisk and Sipura phones. The wiki says Sipura phones only support Auto Answer using the Call-Info header which is no lone shipped with asterisk stable since 1.0.4. I would like to ask if anyone has implemented a similiar facility using Sipura SPA-841 or any other SIP phones. If I could take a look at how

Sipura has implemented auto-answer in version 0.9.5 of the SPA-841 firmware. However, it is implemented via the Call-Info header, which Asterisk stable doesn't currently support. The attached patch implments a quick hack to support the Call-Info header from the Dial() application by way of setting the CALL_INFO variable. For example, the following macro can be used to dial up a single

I just bough a Sipura SPA-2100 to use with Asterisk. When I use the analog handset plugged into the SPA-2100, the person on the other end can hardly hear me. I check the SPA-2100 setup and their is no mic/spk gain control. Is this a problem with the SPA-2100 or with Asterisk? Any way for asterisk to compensate for the poor audio level (if the problem is the SPA-2100)? Thanks, Mike

Anyone have any luck RMAing a Sipura phone since the Cisco take over? Sipura only has support via email or fax to end users and I haven't gotten a response to either for over 2 months. Linksys Support will jump you through all their scripted hoops to resolve your problem (they hope if they speak with a thick enough accent and make repeat the same steps over and over again that you will just

When I use an analog phone connected to a Sipura SPA-2000 it takes about 3-4 seconds before the number is actually dialled. Very annoying especially if you are connecting an intercom to it. Can I change this behaviour and do I need to look at * config or the config of the SPA-2000? Thanks!

Hello, I am very new to asterisk and voip in general and so far have managed to get the FXO card and a few sip phones working fine. My question is where does the Sipura SPA 2000 come in the picture? Can it be used as an extension (i.e FXS) ? Or is it to be used as a line (i.e FXO)? Or it can be used as both? My understanding is that its just like another ATA186. Is that true? I guess what I

Hi, the topic says it all really. Does the Sipura 3000 detect and report UK clid correctly? thanks Mike

Froogle found me one supplier for the SPA-841, not sure I trust them though. Does this phone even exist yet? Does anyone have any experience with it? Does anyone know a vendor other than Atacomm/voipsupply?

Hi all, Anyone able to remotely reboot their password protected Sipura SPA-3000 from command line. I am trying: Sipura SPA-3000 from command line: # wget http://admin:mypassword@192.168.1.55/admin/reboot The strange thing is it works fine when I go to http://admin:mypassword@192.168.1.55/admin/reboot with my web browser... Thanks....

I heard Sipura had really awesome documentation on the SPA-2000 and SPA-3000, but you have to email them for it. When I did, they said I had to get it from a reseller. It's been a while since I bought my units, I don't even remember where or who they were bought from. Can somebody email me the documentation for these devices? I'm quite interested in knowing what every one of their 200+

Hi All, I am using a Sipura SPA-3000 as an FXO gateway to bring calls in and out of Asterisk. I am using "PSTN Ring Thru Line 1" (on the "PSTN Line" tab) so Asterisk answers the call rather than the SPA-3000. It is all working perfectly except I can't get the SPA-3000 to pass caller ID to Asterisk. It passes "Display Name", "User ID" and any "PSTN

Hallo! I had ordered a Sipura SPA-3000 in the UK, but the supplier turned out to be unreliable and never shipped. Yesterday I went looking for alternative suppliers and found the Linksys SPA3000 device. It's a different box, but the specs look very similar. Is this the same device? Has anyone used this Linksys SPA3000 successfully with Asterisk? Thanks, Frank

I have just bought several Sipura SPA-841 SIP phones, and after some testing I have found out that the volume received by other parties when calling using the handset is very low. I've been able to reproduce this problem in the 3 phones I've tested so far. I've tried tweaking several configuration options but nothing I has helped so far. Has anybody else experienced this problem?

Hello, How good is :SPA 841 form SIPURA. Thanks Varun

I just got a refurb Sipura SPA-2000 and was able to assign it an IP address with DHCP and ping the device, but then I ran the firmware upgrade utility to bring it up to spa2k-2.0.13g which seemed to work just fine, but after it rebooted I cannot connect to its webserver for configuration. I can still ping the unit. When I use the built in voice menu it reads back the right IP address, webserver

All- I'm attempting to set up a Sipura SPA-3000 in Sao Paolo, Brazil. Not being a portuguese speaker, I'm having a rough time of finding the relevant information on how to make the thing pick up the PSTN line and make an outbound call. The sipura in question works fine on a bench connected to a POTS line in the US, but is now plugged in in Sao Paolo. The immediate thing I notice is that

I am looking at some lower cost phone to use with Asterisk. What is the ArtDio IPF-2000 or the Sipura SPA-841 like? Also, I see voipsupply.com has an ArtDio IPF-1000 listed, is this a new or an old model? I cannot find any information on it. Adi

Some people on this group may have understood from messages posted here that the Sipura SPA-2000 is not currently available for shipping. That is not the case. Voxilla.com has the Sipura SPA-2000 available for immediate shipping, and has had them since late November. The price is $109.95, and it comes with a month of free VoicePulse service with activation fees waived (a $65 value). In return

If this has been covered before - I appologize. We use some Sipura SPA-2000's with the g711 codec and all seems fine (except for the occasional failure to register errors in my asterisk logs - but I will save that for another post). g711 call quality is on par with our Cisco 7960's. However, when using the g729 codec, the call quality on the Sipura device goes downhill on the PSTN side

Hi all, The problem is on the volume of the voice sent by the SPA-841. I think the echo cancel algorithm sets a limit to the microphone when detects sounds or noise from the earphone. This problem generates an oscillation on the voice volume sent by the phone and even turns it off completely for very little lapses of time making the communication very uncomfortable. I manage three different