similar to: PCI-X PRI hardware

Hi, I'm looking for an interface card for termination of Euro-ISDN2 (BRI) lines. That is ISDN lines from the telco into my Asterisk box. Any recommendations, good/bad expiriences ? At present I'm looking at cards from BeroNet and Junghanns. Cheers, John Faroese Telecom

We are looking to lose the TDM400P in favor of an ISDN-BRI solution. This should get rid of static on the line (at least any static generated by our half of the circuit), right? I am a total virgin to ISDN. I understand that we need two BRI circuits to provide four voice channels, and that the hardware to speak to the BRI circuits can be passive or active, with the active type being much more

Hello We have around 50 phones in our company, and I am playing with the thought to gradually go over to using sip services and ip-phones internally. However at first I would liked the Asterisk just to sit between the phone line and the Panaosnic, so I can take out one lin/number at a time to use ip phones. I am new to Asterisk, and haven't done much configuring of the PBX either. So I also

Hi, I thought I'd check in with people here. Lets say I wanted to put together a Hylafax server, and an Asterisk server on the same box. And, for the sake of making things simple, I wanted to use a single T1 board for both.... Is this possible? I see Eicon boards are supported by both software, so could I have Hylafax and Asterisk installed on a server with an Eicon card, with channels

Hello Everyone, I am once again wondering about EICON. I have had no success with the Diva Pro or Diva Pro PCI, so my question is, does anyone use an Eicon Server BRI card on Asterisk? Or would I be better off trying to get a split PRI? Regards, Greg

Hi, I am starting to look at the costs involved in putting a PBX system together using *.. We will be using ISDN lines in the UK, which when installed provide a box on the wall with 2 analog ports and 2 digital ports, so these seem to be the options available to me.. 1. I could use an ISDN board but I have not really read good things on the mailing list about using ISDN boards, and I suspect

Skipped content of type multipart/alternative-------------- next part -------------- A non-text attachment was scrubbed... Name: VoIP.gif Type: image/gif Size: 17666 bytes Desc: 1197705770-VoIP.gif Url : http://lists.digium.com/pipermail/asterisk-users/attachments/20060213/7ca1c4ac/VoIP.gif

I want to replace a Telebutler software auto attendent system that used a 4 port Dialogic board connected to a Panasonic KXTD 1232 6 line system. We have spare computers here. How do I connect asterisk to this Panasonic system? -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hi, How would one activate/deactivate hardware echo cancellation on the TE406 card? Can it be done per channel? I'm going to run TE406 in the following scenario: ISDN -> TE406 -> PABX I understand from Steve Underwood's site that echo cancellation is not good for faxes (and they do that themselves). So what I want to do and bypass echo cancellation for selected extensions before

Hi! I have some (short) question about the Eicon DIVA (V-)4BRI cards I want to have (short) answered before buying the DIVA card. I know there are several Eicon guys active on the list, thus I ask on the list instead of directly to Eicon so that all other will benefit as well. 1. Do Eicon DIVA (V-)4BRI cards support TE and NT mode? 2. Can the clock (master/slave) be configured independent

Hi everyone, I have Asterisk SVN-trunk-r7498 running for a few months and I'm quite happy with it. However, I am experiencing a quality issue with my AVM Fritz!card PCI which is used with chan_capi. When somebody calls me on this line he hears a lot of noise and I hear "scratches" and "plops". It is very annoying. Below is is my /etc/asterisk/capi.conf I've tried to

Greetings, All-Knowing Asterisk Users List, My company needs to build a reliable fax server that can handle at least 30 simultaneous incoming faxes from the PSTN, using PRI. We realize that this can be solved in any number of ways using a Linux box, but since IVR is also a must, Asterisk popped up as the most promising solution. After combing these lists for clues, we began experimenting

Hello Marc, Could you post the install details for the Diva PCI? I have a Diva Pro PCI 3.0 and I am looking to get it working... I am running Debian Testing. So far it appears there are a few things floating around but I am not certain which direction to go. I know I need to load the firmware first. I did manage to load the modules ok. Thanks, Greg -----Original Message----- From:

Hello, I'm thinking of deploying Asterisk. I already have a handful of EICON Diva 2.01 PCI ISDN cards. I was thinking if it's possible to insert 4 such cards to my PC-Asterisk server (which I yet have to install) and use them as 4 lines in case anyone has to call me in / I have to call out using ISDN line(s)? Any reply appreciated. Tomek

Hello everyone. I need a BRI ISDN card that works in Romania. I already have one of the "Cologne HFC-S" PCI cards and it doesn't work right, it's junk. I get waaaay too much echo using it. I'm now "shopping" for a better card. Can anyone recommend me a card that "fits" the following: (a) Costs less then $1000 / 750 euro (b) Has one or (preferably) two

Hi; I've got an AAH installation where a customer wants to install an active Eicon DIVA BRI card. AAH is built on Centos 3.5 which is currently at kernel 2.4.21.37. Support for Eicon active cards is built-in. I've debugged and run the A@H install-Eicondiva script but when I try to run divactrl load -c 1 -f ETSI -Debug I get a response : A: can't get card type for DIVA adapter

I just wanted to let you know that it's possible to use Eicon DIVA PCI 2.01 ISDN cards (not "server" divas) with asterisk. First thing to do is to load the module. If you have two of these cards, you should do it like that: modprobe -v hisax protocol=2,2 type=11,11 And now you can have up to 4 incoming calls with two cards (try calling yourself and see if anything gets into

Heya Mark (and others), Here's an update on my adventures while trying to debug the Zaptel-related panics, as discussed on this list a while back. While debugging the problem, I completely swapped the machine for an entirely different model (Supermicro dual Xeon 2.4GHz with 2Gb of RAM), put the cards in, recompiled * + Zaptel and administered my stress-test. The machine stayed up in excess

I have read most of Eicons information on Q.SIG, and I am able to load the Q.SIG protocol (instead of ETSI for example). No strange logging in divacrtl mlog. But how do I tell Asterisk to understand Q.SIG? My PBX is configured for QSIG, but I cannot see anything on my trace when trying to make a call via the S0(Q.SIG) Janne > -----Ursprungligt meddelande----- > Fr?n:

Hi Everybody, Has anybody tried the above (or indeed any other 4XBRI cards) successfully with Asterisk. As far as I can see the above mentioned card is an active ISDN card but supported by it's own I4L driver. This leads to interesting questions particularly regarding echo cancellations (which usually doesn't work on the cheap passive cards with one exception as far as I can see).