similar to: Unable to set channel to linear mode

Hi, I wonder if anyone is using Digium's TE110P card on an E1 connection. I have been try to, but so far it wasn't much of a success. It only works more or less in EuroISDN as PRI CPE. And even that config gives me some trouble with channel negotiation. My current config: *zaptel.conf:* span=1,1,0,ccs,hdb3 bchan=1-15,17-31 dchan=16 loadzone=be defaultzone=be *zapata.conf:* [trunkgroups]

Hi there I have a TE110P card fitted in my linux box running : Linux version 2.6.9-5.ELsmp (bhcompile@decompose.build.redhat.com) (gcc version 3.4.3 20041212 (Red Hat 3.4.3-9.EL4)) #1 SMP Wed Jan 5 19:30:39 EST 2005 I followed the installation steps on digium website...no errors reported. The modules seem to have loaded...here's what lsmod shows: Module Size Used by

Hi, I have an asterisk installation with 2 E1 cards Software version is Asterisk 1.2.6 Libpri 1.2.2 Zaptel 1.2.5 I'm having problem with fax transmission, let me explain better my setup: My fist TE110P E1 card is connected to the telco line the second TE110P E1 one to an Nexspan PBX so the server is basically sitting between the line, and the pbx. every call coming from the line is

Hi I am trying to connect asterisk with a Cisco GW 2600 with E1 pri using a Digium, Inc. Wildcard TE210P dual-span T1/E1/J1 card 3.3V (rev 02), Errors: [Jan 28 17:32:33] VERBOSE[6182] logger.c: == Primary D-Channel on span 1 up [Jan 28 17:32:33] WARNING[6182] chan_dahdi.c: PRI Error on span 0: We think we're the CPE, but they think they're the CPE too. [Jan 28 17:32:34] NOTICE[6182]

Hi everybody, I've connected Asterisk 1.2.5 (libpri 1.2.2, zaptel 1.2.4, Linux 2.6.13.2) to an Avaya-Tenovis PBX via a PRI/E1-line. Calls from SIP-phones via * to the PBX work fine. However, incoming calls to * only result in: -- XXX Missing handling for mandatory IE 24 (cs0, Channel Identification) XXX -- which seems to be an * problem, because a Windows-fax-machine works fine on a PRI

For the past month I've been having trouble dialing certain numbers. We have Asterisk 1.4.14, Zaptel 1.4.7, Libpri 1.4.2 on a CentOS 5 server. We are using PRI on a TE110P card /etcwith a provider called Alestra in Monterrey, Mexico. There are some numbers that whenever we dial them we always get a busy tone. These numbers do not all belong to the same provider, but they all do not

Dear all. I have what appears to be a configuration error but I cannot for the life of me see what it is. (I am a newbie) I have searched the wikki and google etc but still none the wiser. Any help would be very gratefully received. Problem: Unable to make outgoing calls via E1 euroISDN Digium TE110p card, given congestion signal as per config, unable to open zap channel. All incoming calls work

Hi, I've connected Asterisk with 4 PRI to a Siemens HiPath 4000. For CALLERID(name) feature I wanna use Q.SIG as switchtype. Cause Siemens PBX orders Channels logical I need the parameter qsigchannelmapping=logical. Here is my chan_dahdi.conf trunkgroups] [channels] language=de context=default usecallerid=yes hidecallerid=no callwaiting=yes usecallingpres=yes callwaitingcallerid=yes

Dear users. My current setup uses a euroISDN E1 with 8 cahnnels for incoming and outgoing calls from a digium te110p. Currently all phones use SIP. However, I need to add some faxes lines and some POS credit card machines. These will require POTS lines with a fixed DDI. I have purchased the tdm400p and 4 FXS modules. My problem is with the zaptel.conf and zapata.conf. I am a little confused as

Hello I just installed a TE110P in a Dell Poweredge 750 (rackmount), which is connected via crossover T1 cable to a adit 600. Anyway, I've encountered an array of errors, which I believe I have narrowed down to the 22 IRQ misses I encounter on zttool. I've noticed that the te110p and the usb device share an IRQ. Could that be the source of my woes? Would disabling the usb device in the

Hi, Been asking google and browsing the lists but haven't found any answers for this. I've connected a TE110P E1 using EuroISDN to a PBX (for me at the time unknown model). All is fine _except_ when placing calls to mobile phones (which takes too long, more than 2 seconds it seems) asterisk seem to be impatient giving up saying the curciet beeing busy. So, what I'm looking for, is

hello, We encountered signaling problem with a french national carrier. They ask us, which signaling is configured on our single E1. I need to know if it's ETSI, VN4 or VN6. I know what ccs, and hdb3 mean but I do not succeed to make the link between the signaling type. I searched through RFC Q.921 and Q.931 It would be great to obtain some help. cedric

Hi, This error I got it just when I gonfigure zaptel support isdneuro 31 channels. But if I configure zaptel to support T1 and just 24 channels I have no problem. ######################################################################## #### # # Zaptel Configuration File # # This file is parsed by the Zaptel Configurator, ztcfg # # loadzone = it span=1,1,0,ccs,hdb3,crc4 bchan=1-23 dchan=16

Hello, I'm using asterisk for a while, fully ip, and i'm now moving to ISDN, so i got a TE110P. The first problem is the "Unexpected Channel selection 3" message. I'm unable to find, on the web, the meaning of such message. Can somebody explain me? My second problem is when a call come in, and hang up. Asterisk shows " -- B-channel 0/31 successfully restarted on

Hi, I a new user of asterisk, I'm trying to in install zaptel drivers on my ISDN card Digium Tiger 3xx TE110P. And my configuration is # # Zaptel Configuration File # span=1,1,0,ccs,hdb3 bchan=1-15,17-31 dchan=16 loadzone = it ; ; ; Zapata Configuration file ; [channels] immediate=no switchtype=EuroISDN signalling=pri_cpe pridialplan=unknown context=incoming usecallerid=yes group=1 channel

Hi All, I have configure my Asterisk as follow (using Asterisk@home): [zaptel.conf] span=1,1,0,ccs,hdb3,yellow bchan=1-15,17-31 dchan=16 loadzone = uk defaultzone=uk [zapata.conf] [channels] switchtype=euroisdn pridialplan=local prilocaldialplan=local internationalprefix=00 nationalprefix=0 usecallingpres=yes busydetect=no ; not need on pri callprogress=no ; was yes but wiki says experimatley

Hi, I'm having problems with a new ISDN PRI in a new server. The cable is connected and the E1 modem seems to have issues with syncing (blinking light on the modem). versions: CentOS 6, asterisk 1.6.2.20, dahdi 2.5.0.1, libpri 1.4.12 ------------------------------------------------------------------------------------ dahdi show status T4XXP (PCI) Card 0 Span 1 RED 0

Hello asterisk-users, I have problem with E1 line between Asterisk computer and our PBX Matra: asta*CLI> pri show span 1 Primary D-channel: 16 Status: Provisioned, Down, Active Switchtype: EuroISDN Type: CPE Window Length: 0/7 Sentrej: 0 SolicitFbit: 0 Retrans: 0 Busy: 0 Overlap Dial: 0 T200 Timer: 1000 T203 Timer: 10000 T305 Timer: 30000 T308 Timer: 4000 T313 Timer: 4000 N200 Counter: 3 My

Hello. I have a TE212 configured in E1 mode. This is shown in a cat /proc/zaptel/2 and 3 (where the card is configured): cat /proc/zaptel/2 Span 2: TE2/0/1 "T2XXP (PCI) Card 0 Span 1" HDB3/CCS/CRC4 RED NOTOPEN 25 TE2/0/1/1 Clear 26 TE2/0/1/2 Clear 27 TE2/0/1/3 Clear 28 TE2/0/1/4 Clear 29 TE2/0/1/5 Clear 30 TE2/0/1/6 Clear

I am running Asterisk 1.0.9 and have been running all my calls through a VSP over a IAX2 trunk however we have recently purchased and connected a TE110p to a PRI ( E1 with 16 voice channels ) through Optus. I can make outgoing calls via it fine, however incoming calls are dropped after a few seconds ( or as soon as a command like Playback, or the call is picked up if forwarded to a SIP