similar to: Asterisk/Zaptel 64-bit?

Dear All, I am currently have this problem in which I am sending call out from the Zaptel TE405 to a VoIP gateway. But the problem that the call over to the VoIP Gateway will always have a fake ring tone. Can you please give some pointer how to fix this problem? This problem is existing in my Asterisk 1.2.1 box. Also when compiling Asterisk 1.2.5 and tried to run it with the Asterisk-addon,

Hi, How would one activate/deactivate hardware echo cancellation on the TE406 card? Can it be done per channel? I'm going to run TE406 in the following scenario: ISDN -> TE406 -> PABX I understand from Steve Underwood's site that echo cancellation is not good for faxes (and they do that themselves). So what I want to do and bypass echo cancellation for selected extensions before

Hi list, Im having a problem with intel 82573L Gigabit Ethernet Controller. Centos 4.2 can't detect this internal ethernet port my motherboard is an Intel Desktop Board D945PSN. when i type lspci the ethernet is identified but when i type dmesg i can't see the ethernet port. -- Regards, Mark Quitoriano, CCNA Fan the flame... http://www.spreadfirefox.com/?q=user/register&r=19441

I just wanted to post here and let everyone know that the TE406P (quadspan T1/E1 with hardware echo can) kicks some serious ass. We've been running a PRI now for over a year with Asterisk (every single call in and out is through two Asterisk boxes, including faxes) and while the software based echo cancellation is more than adequate, we'd get the occassional "edgy" echo and

Dear All, Sorry to be posting again. I have solved my problem. The problem is that when exiting from the macro, the priority number is still in effect. For example, priority 1 is at the start before entering macro after the macro the priorty will be 2. Since there isn't any other dialplan command, the switch statement would be search for a priority 2 in the Realtime extensions table. One

Dear All, It seems that there is a bug on the ooh323 while using registering with gatekeeper. The gatekeeper is GnuGK and the problem is when the Asterisk recieves a call from the Gatekeeper and routes it back out to an SIP Phone. The call would be connected and immediately dropped after 1-2 seconds connection time. This doesn't happen when ooh323 module isn't registered to a

Dear All, I am having some problems with connecting with a UA. Sometimes there is not sound in the call made, sometimes the caller would near no sound, while the callee can hear the caller. I have attached the rtp debug and sip debug for you comments. Please help me. Thank you all. Asterisk Version is 1.2.1 Asterisk RTP Range is 10000 to 20000 UA Listen RTP Port is 15000 Below is the the

Hi all, I changed a bad disk (automaticly disabled from software raid1 and system for I/O error) in one of our servers and now have problem with adding new one to system without reboot. Does anybody have an experience with this? Or is it possible? :) We're using hotswap AXX6DRV3G for 6 SATA disks from Intel connected directly to MB (S5520HC from Intel too). There is AHCI as driver (enabled in

Hi I'm debugging why echo cancellation does not work in my app using the DUMP_ECHO_CANCEL_DATA flag. What format does the data I receive have, looks like 16bit integers just dumped but when plotting it in MATLAB I do not get a raw audio data signal I expected. Kind Regards //Gunnar Gunnar Karlsson HotSwap Stockholm AB Landsv?gen 39| SE-172 63 Sundbyberg, Sweden Mobile +46 739

I have 3 disks that I want to setup in a raid 1, my questions is should I setup the 3rd disk as a spare-disk or should I mirror all 3 disks all the time? Will it perform *much* better to only mirror two and have the 3rd as a spare. Is it not safer to mirror all 3 drives all the time ?

Hello! If I have more than a hundred analog telephones (analog lines) that need to be connected to Asterisk PBX, what kind of hardware do I need, and where can I buy it? Thanks in advance!

Hi All, I am having some problems with Asterisk on static IP and Sipura-1001 on dynamic IP. Is there any solutions to in the Asterisk configuration or Sipura-1001 to re-register when the router change IP dynamic IP? Thanks. Regards, Kengie -------------- next part -------------- An HTML attachment was scrubbed... URL:

I need a SATA RAID PCI card that works well with CentOS and is fully supported. Mandatory features: - works with the drivers already in the kernel, no additional drivers - can do RAID 0, 1 and 5 - hotswap - allows to monitor the status of the array and of each individual drive via a script (ideally run from cron) - works with very large SATA drives Nice to have features but not mandatory: -

From: Rodrigo Barbosa <rodrigob at suespammers.org> > Btw, don't quote me on this one :) > I'm only 90% sure of the hotswapping capabilities, and less than 50% > sure about the price :) There _are_ systems with hot-swap CPUs, memory and/or, PCI[-X] slots. They are _not_ commodity and pricey, and require OS-level support. In fact, I believe Linux 2.6 has some support for

Hi, I have been trying to install CentOS 5.4 on a Intel SR1530SHS, Intel S3200SH mainboard.. It has a 3 x 1TB sata hotswap drives with LSI software raid onboard. I had configured the LSI to have Sata0 and Sata1 with raid 1 and the third drive as a hotspare drive. Format the harddisk and installation was a breeze. The server rebooted into a blank screen and the cursor just keep blinking. Please

I have a raidz2 pool with one disk that seems to be going bad, several errors are noted in iostat. I have an RMA for the drive, however - no I am wondering how I proceed. I need to send the drive in and then they will send me one back. If I had the drive on hand, I could do a zpool replace. Do I do a zpool offline? zpool detach? Once I get the drive back and put it in the same drive bay..

Hello All, I want to build a home file and media server now. After experiment with a Asus Board and running in unsolve problems I have bought this Supermicro Board X8SIA-F with Intel i3-560 and 8 GB Ram http://www.supermicro.com/products/motherboard/Xeon3000/3400/X8SIA.cfm?IPMI=Y also the LSI HBA SAS 9211-8i

Anyone know of a 2.5" to 3.5" converter so I can put a 2.5 SSD drive in a Supermicro 3.5 SATA hot swap bay? The one I purchased does not seem to work.

We're going to replace an older Solaris7/Netbackup/TapeRobot server with a new Centos box using backup-to-disk-to-tape (probably using Arkeia). The specs are up in the air, but generally: - CentOS/RHEL friendly (3Ware SATA? SCSI?) - 2U/3U/4U-ish form factor - hotswap RAID5 - dual PS, hotswap a plus - USB2.0 port(s) (*) To give you an idea of where I'm starting to look, take a gander at

Hey, anyone using an LSI MegaRAID experienced "disappearing drives"...? We installed 6 new C6 servers, each with a Supermicro SMC2108 (LSI MegaRAID) controllers and 3 PX-128M5Pro SSDs ( RAID1 + hostswap). 2 weeks (and almost no activity on it, since not in production, apart from installation) later, megacli sees (based on the slot numbers): - on one server: only the 2nd disk of the RAID