similar to: AW: AW: DTMF detection when outgoing call tomobilephones

Yes I can hear the DTMF keys. I ve tried 2 different phones and 3 different mobile network providers. Nothing. I played with the rx/txgain values from hearing nothing to too loud... I have no more ideas. Marc -----Urspr?ngliche Nachricht----- Von: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com] Im Auftrag von Steve Underwood Gesendet: Donnerstag, 4.

Hi all, I am trying to detect DTMF keys from a mobile when asterisk make an outgoing call to the mobile. The DTMF detection on incoming calls (also FROM mobiles) is working very well. The only problem is if asterisk called the phone... Nothing is detected. I am using a digium te205p with PMX/PSTN connection. Everything that I can find in forums are problems with dtmf detection on SIP. Any

Hi there, we have a problem with dahdi and overlapdial. We are running an E1 in Germany and are in need of overlapdial. The E1 is connected to a Sangoma A101. As soon as overlapdial is set to "yes" we have problems with incoming audio on the dahdi channels. When set to "no" all audio is fine. Basically we can choose between being able to receive calls or to place calls

Is there anyone successfully using the TE410P with a German "PMX-Anschluss"? Please just drop me a note mentioning the carrier you use. We are having problems making the card work, although configuration is correct (Posted this before). Our carrier blames the card for this. We would just need some evidence that it really works. Thanks, Henrik -------------- next part

hello, I have a asterisk box (Slackware 9.1.0, Linux 2.4.31) connected to a Ericsson Businessphone PBX on the internal S0 bus with HFC-S card and zaphfc driver - point2point mode -. --------- | TELCO | | BRI | --------- | | PBX external S0 -------- | PBX | -------- | PBX internal P2P S0 NT Mode | | HFC-S Card P2P TE Mode

I have an Asterisk box (Fedora Core 2, kernel 2.6.10-1.771_FC2smp) connected to an E1 (MFC/R2 signaling) through a TE110P Digium card. My IVR doesn't work because sometimes a single digit is recognized two, three times and sometimes not. I've already changed "relaxdtmf" to "yes" as well as "txgain" and "rxgain" in unicall.conf file but,

Hi *, now for a long time i am trying to set the outgoing callerid, without luck. I am here in Germany, my asterisk has a pri interface connected to a PMX installed by Telekom. All telephone calls are preselected to EcoVoice. I am using asterisk 1.2.7.1, zaptel 1.2.5 and libpri 1.2.2. A week ago we tried with a device able to simulate a telephone system so send out a callerid, and that

Hi, I solved the Problem: the context defined in zaptel.conf: context = zapincoming was not in extensions.conf, so nothing worked. ( I assumend this context is only necessary for calls from zaptel, not to it) This may be a bug: in the verbose log I found nothing like "[chan_zap] Could not initialize ..., due to ....", this had helped alot and had saved alot of hours (-;

Hi, I have Installed * on a DL380 with a Junghanns 4BRI card and 0.0.2 driver. I have 3 BRI lines connected to SPAN(TE) 1,2,3 and 2 Cisco 7960 with SIP image. I am connected to french PSTN (France Telecom) whith Euroisdn signaling. I manage to call SIP to SIP, PSTN to SIP but not SIP to PSTN. Any idea? Thanks Gwenn Gael Marronnier Here is what I get and my configuration...

Hi all, I've got a fairly simple setup, a 4 port zaptel T1 card with 1 PRI and 2 flat e&m T1's coming into it, and its working perfectly except for one small thing. When people dial any of the numbers on either the PRI or the T1 from outside of the pbx, they dont get the "ringing" sound. It just directly connects the call. I know this isnt much, but its started to

Does anyone know how to monitor * to see if they are receiving timing slips on a span connected to a T100P card? I am seeing b-channel restarts quite often and also getting "No D-channels available" warnings from time to time. Yesterday I had all the b-channels crash during a MeetMe Conference. Not good! This PRI is connected to an Avaya Definity PBX that is onsite and located in the

I am running Asterisk 1.0.9 and have been running all my calls through a VSP over a IAX2 trunk however we have recently purchased and connected a TE110p to a PRI ( E1 with 16 voice channels ) through Optus. I can make outgoing calls via it fine, however incoming calls are dropped after a few seconds ( or as soon as a command like Playback, or the call is picked up if forwarded to a SIP

Hi, I have two t100p cards installed. One card connected to the PSTN, the other card is hooked to the Definity PBX with a T1 cross over cable. The card connected to the PSTN works fine. The problem is with the card hooked up to the PBX. The light behind the card is green, but when I dial from this card I get an error. Its says it could start the D-Channel. Could someone help me out with this

I have spent some time this morning trying to add an Astribank to our current Asterisk, but it failed, so I just removed the hardware, restore the config files to the original setup and started asterisk.; I could see that no Zap channels are started so I did load chan_zap.so: pbx*CLI> module load chan_zap.so [Feb 26 10:32:18] WARNING[3809]: pbx.c:2968 ast_register_application: Already have an

Hello List, i am trying to set up an * box with a debian 2.6.10 Kernel. the compilation of asterisk and the zaptel drivers worked almost perfectly. so i did modprobe zaptel modprobe wcte11xp (which is the correct driver for my card) ztcfg -v and this results in ZT_SPANCONFIG failed on span 1: No such device or address (6) I don?t have any ideas whats wrong. google was no help, checking sources

Hi, I have an asterisk installation that has been happily working in production for some time (E100P and UK BT ISDN30). Recently I upgraded to HEAD-07/29/04. Now, incoming callers don't hear ringing while calling in. As far as I can tell, my config files haven't changed from what was working before. Can anyone please help before my boss shoots me? JC zaptel.conf

Hey everyone ! I have a problem in making outbound calls in PRI connection. I have E1 PRI airtel connection [ India ] [ asterisk-1.2.12.1 on CentOS 4.4 ] zaptel.conf ---------- [channels] language=en usecallerid = yes hidecallerid = no callwaiting=yes threewaycalling = yes usecallingpres=yes transfer = yes echocancel = yes echotraining = yes immediate = no ;group=0 ;context = from-pstn

Good Day all, I have a Fractional PRI connected to my Asterisk Box via a T100P card. When I initiate a call out to phone number 123-8888 the call sounds great no echo what so ever. If the person at 123-8888 hangs up and calls me right back (same handset on both sides) same trunk line The call always has echo on it. The Asterisk sip extension hears them selves echoing. The remote party

Hello all. I have an NEC PBX connected via a TE210p E1 line to an asterisk 1.6 box. NEC -> E1 -> TE210P:1 -> * -> TE210P:2 -> E1 -> Telco Incomming calls from the telco to the asterisk box to the NEC work fine with indials and everything. Works sweet. Outbound from the NEC to the Asterisk box fail. Giving an long dial tone that then times out. Ie, pick up NEC handset, dial

I tried to setup an PBX System with the following parties: 1. SIP Phones 2. One AVM ISDN Card with CHAN_CAPI for Outbound dialing and receiving external calls 3. One HFC-S PCI Card in NT-Mode with ZapHfc for physical ISDN Phones. 1+2 work perfect I have problems with part 3 Card is working, drivers loading fine, asterisk initializes chan_zap without problems. Demo did work. My problem is