similar to: PRI Issue: D-Channel woes

I'm trying to install a TE410P this is what happens with compiled zaptel 1.0.9, 1.2-beta and 1.0.9 from http://updates.xorcom.com/iso/ this is my zaptel.conf (checked with the provider the values): span=1,1,0,ccs,hdb3,crc4 bchan=1-15,17-31 dchan=16 loadzone=it defaultzone=it then I modprobe wct4xxp debug=1 t1e1override=15 and the kernel says : Sep 30 16:12:40 localhost kernel: Zapata

Hi anyone have a idea for debug my digium TE405P card ? My zaptel.conf: span=1,1,0,ccs,hdb3 bchan=1-15,17-31 dchan=16 loadzone = fr defaultzone = fr My Zapata.conf: [channels] language=fr context=from-E1 switchtype = euroisdn pridialplan = unknown signalling = pri_cpe usecallerid=yes hidecallerid=no callwaiting=yes callwaitingcallerid=yes threewaycalling=yes transfer=yes

Hi, I'm having problems with a TE420P card, in which I cannot make calls using spans 2 through 4. After a couple of days of working correctly, spans 2, 3 and 4 start failing (can not make calls). The system is configured to work with SS7. After the ACM message goes out, immediately a REL message is returned. I searched for error messages in /var/log/messages and could not find a clue

I have a box with 12 T1s (4 Te410P cards). The PSTN provider is reporting slips and ask me to update the clock source. I have my system.conf set as the following but when I run dahdi_scan only the ports on Card 1 are showing up with syncsrc=1 system.conf : span=1,1,0,esf,b8zs bchan=2-24 mtp2=1 span=2,2,0,esf,b8zs bchan=26-48 mtp2=25 span=3,3,0,esf,b8zs bchan=49-72

Hi, I'm trying to bring up two PRIs from qwest with asterisk and dahdi. I'm using an OpenVox D410E and the drivers are loaded. My system.conf looks like this: # Span 1: TE4/0/1 "T4XXP (PCI) Card 0 Span 1" B8ZS/ESF RED span=1,2,0,esf,b8zs bchan=1-24 # Span 2: TE4/0/2 "T4XXP (PCI) Card 0 Span 2" (MASTER) B8ZS/ESF RED span=2,1,0,esf,b8zs bchan=25-47 dchan=48 These

We are using AAH with Asterisk 1.2.7.1 with a TE405P as listed below. We are getting frequent restarts on the spans which lead to dropped calls. I have pasted some hopefully pertinent information below -- anyone have any clues that might help? Thanks Next line is repeated throughout messages, going through every channel in every connected span. asterisk/full.1:Apr 24 01:15:25 VERBOSE[4196]

Hi, Running 1.4.26.1 here. I have installed TE420B card in my server, and followed the appropriate steps (as far as I know to configure it). This TE420B is connected to a CLEC (T1s), so I am using pri_cpe as singalling type. When I dial out, I get this message: Dec 4 11:37:31] WARNING[27983]: app_dial.c:1275 dial_exec_full: Unable to create channel of type 'DAHDI' (cause 0

TE410P card down. I have three (3) TE410P in one machine running asterisk with SS7. My problems started last week when one of my cards started switching to E1 every time after reboot. I set the following in dahdi.conf and that solve the problem. /etc/modprobe.d/ options wct4xxp t1e1override=0x00 Now all 4 ports on that card is down with Red Alarm. I tried rebooting the machine and

I've seen this consistently on three systems, with three different cards, and multiple versions of DAHDI. At first I thought the issue only occurred on newer, Nehalem-based, systems, but I reproduced it on a Core 2 Duo box as well. I've tested with dahdi-linux 2.2.0.2, dadhi- linux-complete 2.0.0+2.0.0, 2.1.0.2+2.1.0.2, and 2.2.0.2+2.2.0. The card is a Digium TE220B which uses the

I'm using two Rhino channel banks (first 12FXO/12FXS, second 24FXS). These connect to a Digium TE210P card. I'm running kernel 2.6.10 and I've tried Asterisk (w/zaptel) 1.0.9, 1.2 beta, and CVS from today. The results are the same for all versions: Right after I reboot, and modprobe wct4xxp, my analog phone connected to port 13 of the first channel bank (first FXS port) gets a dial

Folks, I recently swapped a TDM400 FXS card that was working perfectly into a new server (running recent CVS), and it's either misbehaving (unlikely), or I've missed something obvious (much more probable). Everything seems to be working, but I can't get any dialtone from it when I plug a phone into any of the 4 ports!! All of the jacks are lit (green lights) but they all seem dead

Dear members of the list, I have difficulties to obtain sync with a Digium TE420 PCI Express For four entries E1, In my case I am with only 3 E1s available to configure. The telephony operator is BrasilTelecom and Signaling is R2 Digital. The information I have is that are E1s with 32 channels, not have sure. My settings Have been based on the link reference:

Hello I just updated the kernel, dahdi-linux and dahdi-tools Im also using now asterisk 1.4.26.1 And im still with a red light (not RED/YELLOW anymore): [root at catumbela ~]# /etc/rc.d/init.d/dahdi status ### Span 1: TE4/0/1 "T4XXP (PCI) Card 0 Span 1" (MASTER) HDB3/ RED 1 PRI CAS RED 2 PRI CAS RED 3 PRI CAS RED 4 PRI

I have the following software installed in a Centos Box with a TE420 (5th Gen) card. . Centos 6.5 64-bit . Asterisk 1.4.22 . dahdi-linux-complete-2.9.1.1+2.9.1 . libpri-1.4.14. Even without plugging in the ISDN into span 1, all 4 spans are flashing red. Plugging an E1 into span 1 makes no difference. My system.conf is just simply: loadzone=au defaultzone=au span=1,1,0,ccs,hdb3,crc4 bchan=1-15

Hi I got the 2nd Gen firmware upgraded on the TE405P. I recompiled after putting in the upgraded board but did not change any conf, but the spans become active but will not come up. I guess I am missing something or are the any changes to the zaptel/libpri software that is required. I cannot find any info about this or does this new firmware only work with latest CVS. I am using 1.0.9 with

List, I have a TE410P (T1 mode, all PRI) and a T100P (fxoks, for fxs channel bank). I cannot seem to get the T100P to send any clock to the channel bank. I prefer that it use the same clock source as the TE410P, but it doesn't matter if it's not in sync just as long as it's there. The TE410P is configured 3x pri_cpe, 1x pri_net. The three cpe go to XO Sonus switch, the net to

Hello, Now that we've had our new Digium TE406P card in production for 4 days we have discovered audio drop problems that happen randomly across all channels. Here's more about our setup: P4-3.2GHz 2GB ram Slackware Linux 10.1 with custom kernel 2.4.29 Asterisk 1.2beta1 Digium TE406P quad T1 card with the following attached: - 2 x RBS D4/AMI 24 channel T1s - 1 x RBS B8ZS/ESF 24 channel

I keep getting a red alarm when trying to setup asterisk to use my TE420B EC. I only have a blank context setup in my extensions.conf as I haven't started to config that until I can clear this red alarm. I don't have physical access to the server, so I can't go reseat the modules/card/ethernet cable, though I have hands on location that have done this a couple times

hi folks. recently some of our customers complained about bad voice quality on the phone system. i looked at the logs and found a lot of these: [2012-11-03 08:26:38] NOTICE[11305] chan_dahdi.c: PRI got event: HDLC Abort (6) on D-channel of span 1 [2012-11-03 08:26:45] NOTICE[11305] chan_dahdi.c: PRI got event: HDLC Abort (6) on D-channel of span 1 [2012-11-03 08:26:54] NOTICE[11305]

Hi All, I am facing problem with E1 line. I have installed Asterisk (1.4.20.1) on a system with Digium TE420 card (Zaptel- 1.4.10) But every now and then I face problem of down E1's. The log show lot of entries like "pri_dchannel: PRI got event: HDLC Bad FCS (8) on Primary D-channel of span 2" This happens on a regular basis and the E1 becomes up after some time. My