similar to: R2 protocol error

Hi All, as good? I am trying to make a call for the Unicall channels and after the exchange of signalling and sending of the digits asterisk locks up with the sending of the signalling "E" and the TELCO says that asterisk would have to send signalling "F", as to make for asterisk to send signalling "F"? The TELCO says that the signalling "E" is

Hi, I am trying to set up an E1 line with CAS signaling using available unicall patches with libmfcr2 implementation. Inbound calls works well, I am able to get DNIS and ANI from incoming call, but I am still not able to make an outbound call with our local carrier. After tweaking of protocolvariant parameter in unicall.conf I was able to find proper values for inbound and outbound calls, but

Hi All, I have an R2 installation still undergoing testings, during the test I notice that the Unicall always respond B6 to a II-1 (from a forward switch). Except, for a DNIS that can't be found in the dial plan, in this case it respond with B5. My real problem is, the call will be terminate on a Cisco 7206 with ISDN/PRI thru SIP. If the Called number is busy or the Cisco 7206 is busy or

Hello All, I'm facing problems with Unicall on this scenario : CentOS 4.3 - Running on x86_64 Asterisk 1.2.7.1 Zaptel 1.2.5 When running zttool , shows all Spans OK. But I can't receive and make calls. I tried to change many parameters and still doesn't work. Any clues ? * unicall.conf [channels] language=br context=incoming-pstn usecallerid=yes hidecallerid=no immediate=no

Hi all, I have Asterisk 1.2.10, zaptel 1.2.7, spandsp-0.0.3pre22 compiled, and a Sangoma A101, and when I make a call I get this: Jan 8 13:04:06 DEBUG[12252]: chan_unicall.c:2000 unicall_exception: Exception on 19, channel 1 Jan 8 13:04:06 WARNING[12252]: chan_unicall.c:627 unicall_report: MFC/R2 UniCall/1 <- 1101 [1/ 40/Seize /Idle ] Jan 8 13:04:06 WARNING[12252]:

Hello! I'm tryuing to bring up an R2 connection but eventhough I've followed the guidelines in: http://zarzamora.com.mx/asterisk/17 something seems to be missing. When an incomming call is generated I get: Nov 24 06:01:17 WARNING[-197416016]: chan_unicall.c:612 unicall_report: MFC/R2 UniCall/24 <- 0001 [1/ 1/Idle /Idle ] Nov 24 06:01:17 WARNING[-197416016]:

Hi, i have one Asterisk with a Digium E1 card, and a Meridian Nortel Release 11. I need to connect both of them. We are using MFC/R2 for this.. The Diagram: [ NORTEL ] ( AMI ) ------------------------------------------------ (DIGIUM) [ ASTERISK] we have green light at the digium card, and at asterisk we see all 31 channels as idle. But when i want to recive a call from the Nortel to the

Hi, i have one Asterisk with a Digium E1 card, and a Meridian Nortel Release 11. I need to connect both of them. We are using MFC/R2 for this.. The Diagram: [ NORTEL ] ( AMI ) ------------------------------------------------ (DIGIUM) [ ASTERISK] we have green light at the digium card, and at asterisk we see all 31 channels as idle. But when i want to recive a call from the Nortel to the

Hi! Im having some troubles trying to configure * as a bridge between a telco and a pbx with R2, the scenario is this: ------------ E1/R2 --------- E1/R2 ------------ | Telco |-------------| * |-------------| PBX | | (Telmex) | --------- | | ------------ ------------ I can receive calls from the telco

Hello everybody, i'm from Mexico, at the time i?m working on a production server with asterisk 1.2.25 + spandsp-0.0.4 + libmfcr2-0.0.3+libsupertone-0.0.2+libunicall-0.0.3 and zaptel-1.2.22. I installed this version of astunicall that i downloaded from http://www.moythreads.com/astunicall/ Everything works fine, i'm able to make outgoing calls and recive incoming calls with all ANI and

Hello all, as good? I am trying to use the package astunicall-1.2.21.0.1 with a Sangoma A104D card and 04 links E1 mfc/r2 in Brazil. The compilation occurred, normally and links is UP if I place in Loop and I obtain to effect called in Loop, but when I extend for the PSTN, links reports the following messages, without asterisk start calls: Dec 5 22:27:12 WARNING[3868]: chan_unicall.c:627

Hi everybody We are having periodically troubles with the outbounds calls, seem like the PBX cannot end to dial the entire string of numbers This is output from the PBX., few minutes after all work fine again ... :(, and few minutes after the same problem appears. Thanks in advanced ... Regards This is the PBX aout and my zaptel, zapata confs. Runing asterisk 1.0.9 libmfcr2-0.0.2

Dear Steve and *.* e1r2 developers and users, now MFCR2 is successfully installed! many thanks for your help. I'm living in Argelia. I have configure my MFCR2 according argentina R2 settigs. (look at the end of the message) the testcall run perfectly (only warnings and I think that is just debug). but I have many problems and when I run Asterisk-MFCR2, generally in the begging no errors

Hello guys! I hope you bare with yet another newbie on the list! :-) I am trying to setup an asterisk installation in between a Siemens HiPath 3800 and my local carrier (Telefonica/Brazil). Both running R2. ISDN is not an option on the carrier. :-( I could apparently setup both E1s just fine according to zttool (both OK with no alarms) but, and this is where it starts to get

Hi, ? I run the program testcall with one E1, it works fine; I receive DNIS and ANI for making calls and answering calls. ? When I start the Asterisk I receive call from outside correctly including DNIS and ANI, and receive the following messages: ? Sep? 7 10:29:59 WARNING[12167]: Answer Call Sep? 7 10:29:59 WARNING[12167]: MFC/R2 UniCall/2 Call control(5) Sep? 7 10:29:59 WARNING[12167]: MFC/R2

Hi all I have MFCR2 successfully installed but seems to get warnings a s seen below when I start asterisk. Am running on Redhat 9. Asterisk Ready. *CLI> Dec 20 08:40:38 WARNING[1175077440]: chan_unicall.c:634 unicall_error: UniCall: mfcr2 far_unblocking_expired Dec 20 08:40:38 WARNING[1175077440]: chan_unicall.c:634 unicall_error: UniCall: mfcr2 local_unblocking_expired Dec 20 08:40:38

Hello All. I'm using sangoma card A-101. tested successful with E10 (ACATEL) Exchange, connection with E1, CAS, (using unicall-0.0.3pre4). my system run success, incoming call and call out are good. when i switch to EWSD (SIEMENS) R-15 . my asterisk faill, cannot connect with EWSD. (E10 and EWSD exchange store in two provinces difference. in Vietnam) this is my logfile of E10

I've been trying to configure an E1 in Mexico using unicall, i went into vozdigital, googled this list, and finally followed this instructions: http://voip-info.org/tiki-index.php?page=Asterisk+MFC+R2 I have 10 PSTN numbers and 10 "lines" assigned, so i only have 10 "channels" assigned from my telco. However when i try to simulate a call using this call file: --------call

Hi, I've finally got running Asterisk 1.2.14 with UniCall & MFC/R2 patches, I can generate calls and all seems OK but I cannot receive any call, this is what I get: MFC/R2 UniCall/3 <- 0001 [1/IDLE /Idle /Idle ] MFC/R2 UniCall/3 Detected MFC/R2 UniCall/3 Creating a new call with CRN 32769 MFC/R2 UniCall/3 1101 -> [2/DETECTED/Seize ack/Seize ack ]

I have a customer that is complaining that any call coming in from Nextel gives a fast busy. We are running Asterisk 1.4.7.1 with Zaptel 1.4.3 and all the MFC/R2 patches and libraries. All other calls go out and come in, just Nextel seems to have this problem. The phone company technician connected a PBX emulator on the line and that one could receive the calls from Nextel. The E1 is provided