similar to: bristuff does not work with TDM400P

Does anyone test Asterisk 1.2.X + bristuff-0.3.X and TDM card? We can't get it to work. -David -----Original Message----- From: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com] On Behalf Of Julian J. M. Sent: Friday, March 31, 2006 1:44 AM To: Chris Earle; Asterisk Users Mailing List - Non-Commercial Discussion Subject: Re: [Asterisk-Users] Re: BRI

Thanks. I think our problem ca be similar. Have you tried to call from analog phone #1 to another analog phone #2? It works. But when you try to call vice versa from #2 to #1 it does not work. When you restart asterisk it works again - but only one direction. -David ________________________________ From: asterisk-users-bounces@lists.digium.com

Hi List, I'm setting up a system with one TDM400P (2*FXO + 2 * FXS) and one Junghanns QuadBRI on a Fedora Core 6 (Kernel 2.6.20-1.2944.fc6). I'm using the bristuff-0.3.0-PRE-1y-e kit. It download zaptel-1.2.16, libpri-1.2.4 and asterisk-1.2.17 When it's the time for ztcfg to do its job it complains with <ZT_SPANCONFIG failed on span 2: No such device or address (6)>

Hi. I'm trying to get a Beronet QuadBRI card work with bristuff drivers. Though qozap module loads right, all card spans are in deactivated status. I'm quite sure my configuration is correct and using a single BRI card instead of the quadBRI the status is active and I can place and receive calls. On Beronet installation manual I read that Beronet and Junghanns cards are identical in

Hey, anyone know if it's possible to receive faxes through a Junghanns bristuff quadbri card? In germany, currently I have faxes coming in on DID line into QuadBRI and then passing to Digium TDM400 (analog) and into faxmachine. But the reliability of TDM card is spotty, so I want to maybe just accept faxes in on ISDN card and save on asterisk system ...? keeping digital signal strong ...

Hi, Reading from www.voip-info.org, i can see that "Junghann's chan_capi is now part of bristuff <http://www.voip-info.org/wiki/view/Bristuff> , as of version 0.3.0-pre". What does that really mean ? Shall I understand I can share a Junghanns QuadBRI board between 2 CAPI-enabled software (like a 0.3.0-pre bristuffed Asterisk for instance) ? If positive, what are the pros and

Hi, I'm trying to install a Junghanns quadbri for a few days but i stay with an asterisk error. (Everyone is busy/congested ) Asterisk is working with a Fritz PCbut from one year and now i want to add the quadbri. The quadbri card has been configured in NT mode and with no 100 ohms S/T termoination. (I'm not sure if the S/T parameter is correct) I have installed the bristuff package

Hi, it helps to have configured and working kernel sources installed. Configure your kernel sources for the running kernel and then run "make" in the kernel source dir to build the necessary scripts. You dont have to wait until the kernel is compiled. best regards Klaus -- Klaus-Peter Junghanns Am Samstag, den 25.06.2005, 02:45 +0200 schrieb Stefan Gofferje: > Hi folks, > >

Again trouble compiling bristuff-0.3.0-PRE-1q with the florz patch on a x86_64 box (I guess nobody is using x86_64 platform or is able to fix this themselves?) First of all when bristuff is downloaded and compile is started it appears that the bristuff Makefiles are badly broken. The asterisk Makefiles all do see to find the kernel sources on a RHEL4 box in the proper directory, the pure

Hi, I am just moving from Asterisk 1.2+bristuff up to 1.6.2, a huge leap :) I was wondering if someone could point me at 3 things that I appear to have "lost"? 1) ZapEC(off) - Is there an equivalent dialplan command to request no EC on a channel before dialling in DAHDI? 2) rxfax(file.tiff) - I have found ReceiveFax(), but I am aware that much has happened in the faxing stakes

Hi, I had problems described in another thread so went from a start, but now have problems when loading qozap module. I get : # insmod qozap.ko ports=9 insmod: error inserting 'qozap.ko': -1 Unknown symbol in module and in /var/log/messages: module qozap unsupported by SUSE/Novell, tainting kernel. qozap: disagrees about version of symbol zt_receive qozap: Unknown symbol zt_receive

Hi all, I'm trying to get a junghanns QuadBRI to coexist in the same machine as a Digium TDM400P card (so I can run the ISDN lines in and bridge with analog phones plugged into the TDM). I'm having a problem loading the modules. If I follow the BRIstuff (0.3.0-pre-1l) install method.... it's to modprobe zaptel, then insmod qozap.o I'm on Debian 2.4.31. That works. But then I

Hi All, How to install bristuff on asterisk 1.2.14? install scripts are trying to download and compile those versions: asterisk-1.0.10 zaptel-1.0.10 libpri-1.0.9 and I'm running: asterisk-1.2.14 zaptel-1.2.12 libpri-1.2.4 I only need Pickup application from bristuff to be able to pickup channel independent calls e.g. when I have incoming call from PSTN and I would like to answer

Hi, I have the SuSe9.2 installed in a box with a QuadBri. I have followed all the instructions i have found and this is my best result... only one error compiling zaptel :( .. y have the kernel sources an already made the links to its drwxr-xr-x 8 root root 328 Jun 16 20:20 . drwxr-xr-x 12 root root 320 Jun 16 14:05 .. drwxr-xr-x 3 root root 136 Jun 16 20:17 asterisk drwxr-xr-x 22 root

Hi All I'm using the PickUp application from Bristuff to allow me to pick up channel groups across Zap and Sip. The only snag is that having picked up a call with it, you can't then transfer it on. Taking a dive into app_dial, it looks like when you specify the T option, it does: ast_set_flag(&(config.features_caller), AST_FEATURE_REDIRECT); Since there's nothing like that

Hi All, I'm using Asterisk 1.2.14 with Wildcard TDM400P. I need app_pickup.so application so I can pickup channel-independent calls from any IP Phone headset. How to compile and install only this application from bristufff package? Thank you in advance, Dominik

Hi Kape, Life is generally good with bristuff and the quadBRI cards. However I've got a concern: how does one return a busy signal to the telco when all B channels are busy? Right now, when all channels are in use, the remote caller is kept waiting until the telco times out and finally get a busy signal (on a land line) or error tone (mobile). On the asterisk side here is the output: --

Hi, Iam dialing from NT ptp to SIP provider. Sometimes Asterisk is doing music on hold but there are no options like t or T in the dial command. As an result the channel got lost and an Hangup occurs. Iam using bristuff-0.3.0-PRE-1y-i on an QuadBri card. Any solution for this? Oct 22 11:20:06 VERBOSE[911] logger.c: -- SIP/sip-08206a30 answered Zap/8-1 Oct 22 11:20:23 VERBOSE[29983]

Hello, I am trying to install the drivers for the Junghanns quadBRI card, but am having a problem. I have essentially followed the procedure from http://www.voip-manager.net/installation-linux-asterisk.php. At the stage to install the ISDN card I have completed the following: 1) downloaded the bristuff-0.2.0-RC8q.tar.gz to /usr/src 2) unpacked it in /usr/src - tar xvzf bristuff-0.2.0-RC8q.tar.gz

Hi Alessio Yes, the problems you report do seem similar to the issues I had. I found on the Dells that the audio prompts were very choppy and played slower than normal. Occasionally there would be 'bursts' oav a second or so of 'good' audio. I also suspected IRQ issues but the Dell Mobos had no way of adjusting them. Best thing is to try and get the card on its own unshared