similar to: pots -> asterisk -> tsu-600

Hello, I have just received Adtran TSU 600 with 24 FXS ports. I have installed sucessfuly T100P card. Adtran is connected to t100p with crossover T1 cable. On T100P card I have a green light and on Adtran I do not get any errors or alarms. But I do not get dialtone on FXS ports. Adtran is configured: For Network Timing, fxs ports ore fxs_ls on Adtran. In zaptel.conf: span=1,1,0,esf,b8zs

Hello, Did anybody successfully tried upgrade Adtran TSU 600 to firmware which is working properly with T100P and asterisk ? B.

I have just received a T100P and an Adtran TSU 600 in the mail. I seem to be having a problem with the T100P card. So far I have done the following: vi zaptel.conf fxoks=1-22 fxsks=23-24 ... vi zapata.conf ... signalling=fxo_ks ... channel => 1-22 ... signalling=fxs_ks ... channel => 23-24 I then run modprobe zaptel modprobe wct1xxp ztcfg -vv There are no errors to report. In

i wrote previous about a setup i thought might work with asterisk and the tsu-600. no one replied, so i thought i would ask if anyone is using a tsu-600 with asterisk and if so how do you have it setup ??

can anyone recommend a asterisk "turn key" company. we will need the hardware as well as tech. support 24/7. we'll want all the goodies, voice mail, auto attendant. we have 6 incoming pot lines (all the same number), and 40 normal telephones. we have no interest in changing to ip phones or the pot lines at this time. we're interested in removing our meridian pbx system,

People on the list tend to think you can't make many cards work on a regular desktop. If you're willing to wait a couple of week I might have an answer for you. _____ From: Robert Augustyn [mailto:augustynr@yahoo.com] Sent: Saturday, December 11, 2004 7:13 PM To: Asterisk Users Mailing List - Non-Commercial Discussion Subject: [Asterisk-Users] Will Adtran TSU 600 work with *?

All, Thanks for taking time to read. I am wanting someone to tell me that I have a clue here and that the following proposed setup would (possibly) work. Currently existing are 4 pots lines with qty. 10 AT&T 954/854 phones. Would like to convert to asterisk and at the same time do a mild feature upgrade. Proposing to get: PIII 800MHz or better >=256MB RAM

It is possible to connect ADTRAN TSU 600 VP24 FXO 24 Port Channel Bank to Asterisk ? Somebody offered me that hardware, but I do not know if thats good hardware for Asterisk. rgs, Bartosz -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20030820/4a9e4608/attachment.htm

Here is some more stuff to add to the confusion about the "callprogress" option. I currently have my * system operating with a T100P talking to an ADTRAN TSU600 channel bank with 8 FXO ports connecting to the outside world and Grandstream SIP phones as handset extensions. At first I naively set "callprogress=yes" in zapata.conf. The results were typical of what many

What they are probably marketing is putting in their own equipment out there. I install a product that does exactly that. A paradyne jet fusion. It takes care of the part of which channels are data and which are voice. If it's anything like these, the lines will come out on pairs. You will then have to use channelbank and FXO/FXS cards to get it into your phone system. The jet Fusion

Hi 2 all. I've a nice issue my * system. I have: asterisk latest cvs T100P + Zhone cb (3fxo+10fxs used) Diva Server 4BRI running Capi a bunch of pots and sip phones The whole system is running good (thanks to capigod and Bic. for the help with the Eicon Diva), but there's a very strange issue when calls arrive on the Diva and then bridged to the pots on the channel bank: the voice is not

Hi all, I am either going daft or not reading things right. I have just installed, (well 10 hours ago) a TDM40B and 3 X100P cards. I have followed the examples for the conf files to the letter. I can call the pots extensions OK from IAX clients, SIP clients and from the incoming X100P cards. But, if I pick up the handset to make a call all I get is the engaged tone and the following message.

Hi guys, I've run into a problem that I can't figure out on a bunch of handsets I have running into a Rhino Equipment 24-port FXS channel bank hooked up to a T100P and running asterisk-0.9.0 and the associated stable Zaptel release. The sidetone (your own voice that you hear in your handset, built in for comfort) is noticeably louder than it should be, and it doesn't seem to

Peter - 40 phones and only 3 PSTN trunks?. I would recommend at least 2 BRIs for this. If you have ISDN you can also get DDI to the extensions.I would strongly recommend abandoning the analogue PSTN lines and using ISDN. The setup pain you will go through will be significantly less, combined with better audio, more features (like DDI numbers!) and much more robust connections. You should look

I have a pri comming into a t100p in my asterisk box. I have a second t100p configured as pri_net connected to a nas server. I can route modem calls to the NAS with no problem, but I am concerned about isdn data connections. Will asterisk route 64k isdn calls between 2 t100p's? Also, should I expect worse modem connections than normal? Chad Sawyer -------------- next part --------------

I've got an * system that is having some real problems with 1.0.2. The biggest problem is that calls going through my T100P get choppy for about 10 seconds every 1 or 2 minutes. Asterisk is running on a debian stable system with current packages. The T100P is plugged into a Adit Channelbank with 8 POTS lines hooked up to the Channelbank. I've watched the vritual memory and CPU status on

Our basic system is as follows: P4 3.0 Ghz w/ HT, 1GB PC3200 RAM, 120 GB HDD, RH 9.0 OS, * from CVS several weeks ago, working OK for routing, VM, and AA, calls in on separate PSTN lines to Adtran TSU 600, into * server through T100P card. The hardware is not taxed at all with little over 20% proc utilization ever, low mem use, etc. All Phones are SNOM 200's with various firmware revisions

Hello. I am totally new to this PBX/asterisk/telephony world. I understand that what I need between the T100P/E100P and the POTS analog lines is a channel bank/multiplexer? I am looking for recommendations on this type of hardware. I have been looking around and found a product from valiant communications (http://www.valiantcom.com/) and/or

Hi ! I am connecting to Adit 600 thru a T100P card I have configured 1-16 FXS channels and 17-24 FXO. Everything looks fine on Asterisk side I get a tone on all FXS channels, but when I try to dialout thru one of the FXO channels 17-24 it doesn't connect to the POTS line and echoes back my voice. I use fxsls and fxols for the T1 channels and ls on Adit side. Whats wrong here ? here is my Adit

Hello, I've spent a couple days searching and posted into the forum with no luck, apologies to anyone who reads the Digium forums for the cross-post. I'm having a problem with an asterisk set up where I have a TDM402B connected to a POTS line. Also connected to the POTS line are plain telephones, non SIP, just plain old telephones. When one of the normal handsets goes off-hook,