similar to: Hangup issues

I have a very strange problem I'm hoping someone has encountered already. I've scoured the internet for an answer to this one. My phone company provides no disconnect supervision. Hence I'm forced to use the busydetect feature. I have a TDM400 with two FXO ports. If I call from an internal extension to a landline and then hangup the landline Asterisk detects the busy signal

Hi, I am using TDM400 card with 3 fxs and 1 fxo. I am struggling to detect hangup tone or disconnect supervision tone from my CO. I attached the recorded wav file which contains my telco's disconnect supervision. I am using , asterisk-1.4.33.1 dahdi-linux-complete-2.3.0.1+ 2.3.0 OS => Debian-lenny 5 users.conf ------------- [trunk_1] trunkname = pstn ; GUI

Hi all.. I have a problem with my asterisk installation. I'm using a Wilcard X100P clone in Spain. Incoming calls work fine, but when I make a outgoing call, a hear the ringing, and the peer phone ring, when the peer answer, asterisk hangup the call, or say busy. This is my conf: zaptel.conf: --------- loadzone = es defaultzone=es fxsks=1 zapata.conf ---------- [channels]

Hi, Im working with the following versions: -asterisk-1.2.12.1 -zaptel-1.2.9.1 And with the following card: 00:0d.0 Communication controller: Tiger Jet Network Inc. Tiger3XX Modem/ISDN interface Subsystem: Unknown device 8085:0003 Flags: bus master, medium devsel, latency 32, IRQ 201 I/O ports at c800 [size=256] Memory at fe000000 (32-bit, non-prefetchable)

Hi, I am using asterisk 1.4.28 with freepbx and Wildcard TDM410P card. Everything is working fine except the caller ID of incoming call from PSTN line. The phone display is showing "Unknown" when there is an incoming call. *My log file showing this while an incoming call on PSTN line:* tail -f /var/log/asterisk/full [Dec 30 06:36:16] DEBUG[2559] dsp.c: dsp busy pattern set to 0,0

Hi, Im getting mad with this error, I have a x100p installed with wcfxo module loaded perfectly, I can receive incoming calls and detect very good the hangup for incoming calls. But for outgoing calls its a mess. When I place a call for outgoing, i heard the ringing, my cell or phone rings and when I pick up the phone it hangs: -- Called g1/91xxxxxxx -- Hungup

Hello, I've one astribank with 8 FXO unit and 8 pstn lines connected to the astribank. When I receive calls on my ipphone I get always Unknown callerid. It's is possible to receive the callerid from the lines on the astribank unit? This is my config: [channels] language=es context=from-zaptel signalling=fxs_ks ;rxwink=300 usecallerid=yes callerid=asreceived ;cidsignalling=bell

Dear list, We have an weird problem with our FXO card (TDM01B). When I made a call using this channel, all goes well, the called phone rings but when the called phone answers the call. In me handset I can hear an weird sound like a "Clack". I tryed diferents TDM cards and modules, and my zapata.conf is like, language=en context=from-zaptel switchtype=national usecallerid=yes

Today I received a TDM11B (1 FXO and 1 FXS) and got it installed just fine. I bought the card mainly to get caller ID to work properly in Sweden, and that works just fine. However, if the called or calling party hangs up after I hangup my SIP channel, polarity CID detection kicks in and dials a couple of signals to my incoming context. This happens with Asterisk 1.0.6 and CVS-HEAD. I have tried

Hello my friends... We are having some problems with the fax in our asterisk server... We have: Asterisk 1.4.21.2 Zaptel Version: 1.4.11 libpri version: 1.4.5 Digium Card TDM 410P This digium card has 3 FXO ports and 1 FXS port where we have a fax machine connected! The problem is that we can receive fax very good, but we can't make any outbound fax call, in fact, our asterisk get freezed

Hello, I have a TDM400P with 4 FXO ports, currently using three. When sending or receiving calls on this card, there is a nearly constant popping/clicking sound, it is related to the echo cancellation?. I adjusted my gains properly, but to no avail. I even found that setting echotraining=no in zapata.conf didn't change the scenario at all. I've plugged analog handsets into the

Hello guys, I have this problem when a call is received in my PBX: (Caller) --> (Redirecting Service) --> (E1 PRI) --> (Asterisk PBX) --> (Internal Phone) Reception works fine, but when conversation finishes and the agent at internal phone hangs up, the call at caller's side is still alive for many seconds until it hangs up. The problem is that Telephone Company is billing me

Greetings listers. I'm running asterisk 1.4.21.2 on SUSE 11.0 using Polycom 501 phones. My outgoing connections are Zapata using a TDM401P. For the most part I can make and receive calls fine except for these 3 issues: 1. When I call an external conference, the call never bridges and hangs up after 60-90 seconds. 2. When I call another number there is a

hello, I have instaled a analog line, and when I call on the console apears that: I want to redirect the call to 101 extension. *CLI> -- Starting simple switch on 'Zap/1-1' == Starting Zap/1-1 at default,s,1 failed so falling back to exten 's' == Starting Zap/1-1 at default,s,1 still failed so falling back to context 'default' Apr 27 08:15:53 WARNING[3494]:

Hello all, Recently I just instaled asterisk-1.2.14, zaptel-1.2.12, libpri-1.2.4 and Freepbx v.2.2.0. My zapata.conf look like this, (Pasted bellow) The problem is that the asterisk never send the callerID to the phones. I just take a look to the cdr database an there is no callerid too. I do not know why the calledID is not receibed. All this FXO ports are conected to a mobile lines and if I

Hi, I've got a problem with my asterisk set up which has been going on for a while (months). I'm currently running 1.2.7.1 on a gentoo box with the topology below: +-----+ PSTN ---------+ * +------------- Service Provider (wctdm400p) +-+-+-+ IAX | | | | FXS --+ +-- SIP (cisco 7940)

hi: In my zapata.conf i have 4 fxo configured channels,for fxo number 1 to 3 i added polarity reversal property but for fxo number 4 i didnt add polarity reversal property but it still giving me on cosole that fxo number 4 is polarized (because the line on fxo number 4 is not polarized). what i want to do is to not let polarity reversal take effect on fxo number 4. that what i have in my

Thanks for your suggestion Steve. I have done as you advised and set busypattern=300,200 to match the sample I recorded. This hasn't worked though, asterisk doesn't seem to detect the busy signal. Does asterisk require a the signal to be in a certain power range? The signal I get is very quiet. Thanks for your help Regards Jonathan On Mon, 19 Dec 2005, [ISO-8859-1] Diego Andr?s

Hi , I have a problem with a X100, i do a external call to the asterisk server . The dialplan its simple answer and hangup.. when it's done , the telephone which i did the call , is in line but asterisk server is finish. I'll apreciate all your suggestion. Greetings, txus. The asterisk output: -- Executing Hangup("Zap/1-1", "") in new stack == Spawn

Hello, my config : aah 2.6 (asterisk 1.2.4) , centos 4.2, 1 TDM11B (1 Fxo / 1 fxs ), 1 phone, 1 softphone I'm in France When someone from PSTN calls and hangs up before the call is answered, internal extension keeps ringing until timeout occurs. PSTN line keeps busy. Hangup detection doesn't work. I've played with different paremeters (callprogress, busydetect, busycount,