similar to: Polycom voice.gain.tx.analog.handset and asterisk echo

Hi, I just got and setup a new ip500 yesterday and it worked for about 15 minutes. Then it froze during a reboot.Now, when power cycled, the logo comes on for 3 seconds and then the screen is blank and nothing further happens. 468* factory reset doesn't work. I am about to send the phone back, but wonderd if anyone had a suggestion first.

Hi, I just got my ip500 back after months of waiting. Is there an easy way to get it hooked up to asterisk without [t]ftp servers and all that or is there a quickstart page somewhere? tia r

What gives with the stupid stupid power system on the Polycom IP500 (I hope they changed it on the 501's). Anyway, does anyone know if you can get some type of joiner to connect two Cat5 cables together, and will this affect the call/signal quality because my Ethernet cable is longer than the dumb 11ft polycom supply (oh and their manual is the wrong about which end goes into the handset

Hi, I have lookedaround and don't see this anywhere. Is there a way to tell the ip500 to not make the aural MWI blips?

Could not find your post for 4 months ago. -------------- Original message -------------- From: "Anton Krall" <akrall-lists@intruder.com.mx> > Yes, check a post that I made about 4 months ago, I posted the cofig for > setting the speaker, handset and ring volumes .. > > |-----Original Message----- > |From: asterisk-users-bounces@lists.digium.com >

Hi all, I'm researching IP phones for a new office setup. We will need 30 phones. I have read the wiki and the polycom site for the phones, but I still had some questions about real world experience with these phones. -According to the documentation, the 500 series ( and 600, according to a polycom rep ) have built in hubs. Has anybody noticed performance issues in this setup, when

Anyone else have problems with soft buttons not being responsive at all? 2 of the 4 soft buttons do not respond, no matter how hard you push. It is an IP500. Well over 1 year old. -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20061208/b3fa0b42/attachment.htm

Hi, Has anyone used polycom phone IP500/600's conference feature? I ran into some issues. Polycom is not behind NAT. Polycom calls pstn number A, (gets two way voice), presses conference, (A is put on hold), calls pstn number B, (gets two way voice), presses conference again, suppose to have all three parties in the call, polycom and B have two way voice, but polycom doesn't have two

Hi I am struggling with hardware choices to get started with. My options are narrowed down to SIP phones - Polycom IP500, IP600 and Cisco 7940G. of importance is: - functionality / integration with asterisk - headset functionality and use - voice quality - build quality Is there much of a difference between Polycom and Cisco? Scanning the group it looks like there may be slightly more

I have the following situation: Asterisk 1.2.1 25+ Polycom 501 telephones. Bootrom 2.6.2.0032 Application 1.6.2.0041 Some 501's local to my network, some across the great INTERNET divide. PRI connected to Sangoma card. Issue: horrible echo (and squeals, and "underwater-like" sound) on speaker phone when calling from extension to extension. echo not present when calling outbound

I've had an IP300 for a while now and it's been working fine. I just got an IP500 and when it connects to the FTP server it downloads the new bootrom and says error loading. The bootrom is fine and works on the 300... In addition, I downloaded a new copy to be sure and it still doesn't work. Can anyone give me some advice?

I'm guessing that I need more info entered into the 'message centre' section. What did you key in? Paul Hales IT Support Adairs -----Original Message----- From: Jeff Pyle [mailto:jpyle490@gmail.com] Sent: Friday, 17 September 2004 11:27 AM To: Asterisk Users Mailing List - Non-Commercial Discussion Subject: Re: [Asterisk-Users] Polycom IP500 I have two IP 500's on my Asterisk

Hello, I have configured my polycom ip600 and ip500. The phone works well. But the clock is wrong and flashes the whole time. Drives me nuts! I have set the time offset on the DHCP / boot server. 36000 (I'm in Australia!) It doesn't seem to help... Mike

Hello, I am looking at the Polycom phones. The ip600 has a very nice screen, is that the only real advantage over the ip500 and ip300.. Is it worth the extra dollars? Kind regards Michael Felder IT Medic Australia Pty. Ltd. P: 03 9557 2213 F: 03 9557 2214 M: 0419 568 217 E: Michael@ITMedic.com.au <blocked::mailto:Michael@ITMedic.com.au> http://www.ITMedic.com.au

Hi All - I'm running version SIP version 1.3.4 on various IP300, IP500, and IP600 Polycom phones. I'm having a tough time with MWI. I thought I remembered somebody on the list saying that they had it working, but I can't find it in the archives now. I have all the phones configured for MWI as specified in the WIKI: ipdmid.cfg: up.oneTouchVoiceMail="1"

Hi Everyone, I've been asked to determine which phones our organization should go with. And I've narrowed it down to the Polycom IP500 or the Cisco 7940. From my travels through google, it's hard to find a definitive comparison of the two phones. So I thought I would ask the people that have probably used both. From what I can tell, the only major benefit the Cisco has over the

Is there a way to initiate a transfer using an analog handset? For instance I'm looking for a way to do something like the following: External call comes in and is answered by user A. After talking to the caller they determine that the caller really needs to speak to user B. Is there any way for user A to initiate a transfer to user B, using only their analog handset? Now to make

Does anyone know where I can get replacement handsets for the Polycom SoundPoint IP phones? Or does anyone have any they want to sell? From the looks of it you have to buy a whole new phone to get a new handset. My vendor, TriaTechCOA, told me I had to buy a whole new phone to get a handset, which is pretty ridiculous. Maybe there is a more sane vendor I should be buying from? Thanks, -Ryan

I am trying to use a Polycom Soundpoint IP400 with my asterisk setup, and have been unable to find the proper firmware and application files to make it work. The phone can access the FTP server, and downloads the IP500/600 configuration files, but claims that the sip.ld file is larger than its file system. I can think of two possible ways to make this work. One is to find the IP400

Hi All, I have a Polycom Handset on a front door and I'd like the phone to dial a number as soon as the handset is lifted without having to press and buttons or enter any numbers. I know how to do this on a Linksys but I can't find out how to do it on a Polycom. I would be greatly appreciate is some is able to tell me how this is accomplished. Regards David. -------------- next part