similar to: ZapATA channels up, but calls cannot be made

Hi, I have this error, I have a digium card TE110P Tiger3xx When I'm load the dirvers by this command modprobe wcte11xp I got this error "Notice: Configuration file is /etc/zaptel.conf line 0: Unable to open master device '/dev/zap/ctl' 1 error(s) detected FATAL: Error running install command for wct1xxp " when I'm Lunch the command ztcfg -vv I got this error.

Ok so I read the Linux 2.6 related README and finally compiled propperly, I thought but at the end I notice that lscpi does report the cards, but I cant modprobe wcfxo nor zaptel and I do have wcfxo.ko in the /lib/modules/2.6.8/extra/ directory, so what gives? This is a Debian Sarge, thanks! # # make clean starts here # make[1]: Entering directory `/usr/src/zaptel-1.4.0/menuselect' rm

*This message was transferred with a trial version of CommuniGate(tm) Pro* In setting up Asterisk, I'm looking to dump my current phone system (Nortel Venture). I presently have three POTS lines. I would use a VOIP provider, but now are presently available in the Toronto, ON, CANADA area that support user owned hardware/software. I need a 416/647 area code number. In looking at FXO cards

i've been using *1.2 w/ realtime static zapata in mysql table fine. but after i upgraded to 1.4. it seems like the zapata table doesn't load correctly. i have to go in the console and use the "zap restart" to get the zap channels register. is this sounds like a bug or something i'm missing when upgrading to 1.4? -- Edwin Lam <edwin.lam at officegeneral.com> Systems

is where anyone who can tell me how it's possible to set nationalprefix & internationalprefix for a single isdn-card and not for all installed cards ?

Just wondering if there is a reason PPP support is compiled into zapata by *default*: # Uncomment for Generic PPP support (i.e. ZapRAS) # KFLAGS+=-DCONFIG_ZAPATA_PPP Especially since the comments imply that it should be commented out by default... The main reason I ask is because I usually try to re-compile the kernel to only include the bits that I need, and so I don't include PPP...

I just installed two new X100P's today in my RH7.3 box and was poking around /proc What does the RED refer to on board 2? /proc/zaptel/1 Span 1: WCFXO/0 "Wildcard X101P Board 1" 1 WCFXO/0/0 /proc/zaptel/2 Span 2: WCFXO/1 "Wildcard X101P Board 2" RED 2 WCFXO/1/0 Any clues on how to setup channels on the two interfaces?? I am up to here in

hi! when i have busy signal on analog line (zap card) it doesn't detect that line is busy ? is it possible to change detected sequence (frequency) of busy tones on line (zapata.conf ??) tnx, Thomas my zapata.conf [channels] language=en context=lin1 signalling=fxs_ks channel => 1 group=1 echocancel=yes echocancelwhenbridged=yes rxgain=3.0 txgain=3.0 busydetect=yes

Hi, Do you have some experience with the "best" values for those parameters in youyr particular case? I mean the best raport between sound level in both direction and echo cancellation. For me, the best result I can get is with: rxgain=10 txgain=15 ... the sound level is good, but the echo is a little bit to strong for my taste. Something interesting is that if I put a txgain value

Hi I've problem, i cant get tone on a FXS ZAP channel my configuration are: -- zaptel.conf -- fxoks=1 --zapata.conf -- [channels] immediate=yes context=bell signalling=fxo_ks channel=1 --extensions.conf -- [home] exten => 500,1,Dial(IAX2/guest@misery.digium.com/s@default) [bell] exten => s,1,SetCallerId(${CALLERID}) exten => s,2,Dial(${PHONE},16,tr) ANY IDEA?

Hello- As part of the asterisk build/installation instructions it mentions that the zaptel drivers should be built and configured first. My question is whether they are required at all, in the case of a system with no hardware cards at all (as is the situation in my case). With them loaded I continually get the following message on my console (server not asterisk): Zapata Telephony Interface

I'm not sure how I can handle timeouts and invalid extensions for my Zaptel channels... Their default context is [internal], and in internal I have defined extensions i and t to handle timeouts and invalid extensions. However, the default for the Zaptel channels is "immediate=no", so the default context is only "run" when input has been entered. This means that the i

HI, I'm trying to config a span from port 2 of a DIgium T410p to a Brooktrout TR114-P8V-T1 card. I have a T1-PRI from the TELCO in port 1 (thru first port) working just fine with Asterisk 1.0.3 - been working fine for some time now. No problem with dialplan PSTN calls. Now I'd like to "route" specific DID numbers in thru the TELCO T1-PRI and out thru the second port (span) on

You should go here and enter your suggestion so the developers can track it. http://sourceforge.net/tracker/?group_id=123387 Cheers, Wiley -----Original Message----- From: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com] On Behalf Of Aaron Glenn Sent: Thursday, March 10, 2005 4:38 PM To: Asterisk@Home Cc: Asterisk Users Mailing List - Non-Commercial

I currently have two channel groups in my zapata.conf file. I would like one group to be immediate=yes and the other immediate=no Does not seem to matter which way I go, the first entry in overrides my explicit setting for the second group. I am running * 1.0.9 on FC1 [trunkgroups] ;trunkgroup => 1,24 trunkgroup => 1,48,72 ;spanmap => 1,1,0 spanmap => 2,1,0 spanmap => 3,1,1

Hi guys Forgive the newbie question but I am setting up my first * system :-) I live in the UK with two standard BT phone lines. The hardware used is a TDM400P with two FXO and two FXS daughter boards. Currently only one FXO and one FXS line is used during testing. Incoming calls work fine, as do the phones plugged into the system. However outbound calls do not work. The number is dialled,

has anyone an idea how to display incoming national/international isdn-pstn-calls correctly to internal isdn AND sccp/sip-phones ? without nationalprefix=0 and internationalprefix=00 I get incoming phone numbers correctly on isdn-phones but the leading zero's are stripped of for non-isdn phones when I set this prefixes inside zapata.conf my internal isdn-phones get this prefix twice...

I have a TE110P Digium card. I am trying to receive fax, but the fax are almost always unreadable, i.e ============================================================================== Oct 17 15:21:20 DEBUG[4054]: Pages transferred: 1 Oct 17 15:21:20 DEBUG[4054]: Image size: 1728 x 1157 Oct 17 15:21:20 DEBUG[4054]: Image resolution 7700 x 3850 Oct 17 15:21:20 DEBUG[4054]: Transfer Rate:

Sorry if this is a double-posting. I tried sending the following message Friday afternoon, but it still hasn't made it to the list. Based on the comments in the extconfig.conf file, zapata.conf *should* support being loaded realtime. Has anyone succeeded in doing so, and what does the schema, etc look like? Thanks! Steve

I've been trying to change the musiconhold= in the zapata.conf to use something other than default. However it doesn't seem to do it. I know the other musiconhold source works but whatever I set it to in the zapata.conf file it always plays whatever is [default] in musiconhold.conf. Also random=yes doesn't work. [default] mode=files directory=/var/lib/asterisk/mohmp3 random=yes