similar to: Problem with two cards Digium

Hi, I'm cutting my teeth setting up a home asterisk server, but having some trouble getting Zaptel to recognize a X100P clone PCI (Motorola SM56 which should work according to various wiki's). What struck me was that the "/proc/interrupts" do not include IRQ 11 as the "lpcpi -v" is reporting. Am I missing something fundamental here? Any hint is greatly

Hi, On a Lenny system, with dahdi 2.4.0, libpri 1.4.11.5 and asterisk 1.6.1.18, I inserted a new Digium HA8 + B400M card. My usual installation fails. I can see it listed : # lspci -n | grep d161 01:0b.0 0200: d161:8007 (rev 11) # lspci -vn 01:0b.0 0200: d161:8007 (rev 11) Subsystem: d161:8007 Flags: medium devsel, IRQ 22 I/O ports at d400 [size=256] Memory at

Hi, Before I report a bug on http://bugs.digium.com, I would like to know if someone is seeing the same error message. Personally I am not using wctdm24xxp but other modules such as wcte12xp and wctdm. The latter modules load fine and are compiled with pci_register_driver as expected. The only module that seems to require the deprecated function pci_module_init is wctdm24xxp. Is this normal?

Hi list, I installed 2 HB8 cards each of them with a Quad Bri modules in a HP 360 G6 running Debian Squeeze. Here is an output of dmesg wafter server has booted: [ 9.784123] wctdm24xxp 0000:0b:08.0: PCI INT A -> GSI 31 (level, low) -> IRQ 31 [ 11.847073] bnx2: eth0 NIC Copper Link is Up, 1000 Mbps full duplex [ 11.847600] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [

Hi, On a (bogus) system equiped with a Digium HA8 and 8 BRI ports, I'm reading this: # asterisk -rx "dahdi show status" Description Alarms IRQ bpviol CRC4 Fra Codi Options LBO HA8-0000 RED 109 0 0 CCS AMI YEL 0 db (CSU)/0-133 feet (DSX-1) HA8-0000 UNCONFI 109 0

//////////////////////////////////////////////////////////////////// Hello to all, I have a question. I am installing te110p, when I give ztcfg him - v leaves the following error to me ZT_CHANCONFIG failed on channel 25: No such device or address (6) - That means east error? - It is a physical damage of the card? Thank you very much

Hi gang, We are moving our computers from a cluster of physical machines to a VMWARE server with virtual machines. We investigated and are looking to replace our TDM400P/TDM410P with AEX410P cards. Can we run asterisk with the DAHDI drivers from one of the Virtual machines or is DAHDI going to have to be a native process on the "REAL" machine? Thanks Danny Nicholas

I'm trying to configure a TDM808P card on debian. When I modprobe wctdm24xxp i get this error FATAL: Module wctdm24xxp not found. FATAL: Error running install command for wctdm24xxp I think i have successfully compiled the zaptel drivers, and the card appears when i do a lspci 02:06.0 Ethernet controller: Digium, Inc. Unknown device 0800 (rev 11) Subsystem: Digium, Inc. Unknown

Hi. Please help. When trying to compile Zaptel 1.4.5.1 I get the following: /build/include/linux/modversions.h -DSTANDALONE_ZAPATA -I.. -o base.o -c base.c base.c:48:29: linux/workqueue.h: No such file or directory base.c:292: warning: `vpm150m_firmware' defined but not used make[2]: *** [base.o] Error 1 make[2]: Leaving directory `/usr/src/zaptel-1.4.5.1/wctdm24xxp' make[1]: ***

Hi, I'm facing an issue with which loading wctdm24xxp module fails. Here is relevant dmesg's output : [ 13.455729] dahdi: Telephony Interface Registered on major 196 [ 13.455729] dahdi: Version: 2.4.0 [ 13.510847] ACPI: PCI Interrupt 0000:01:0b.0[A] -> GSI 22 (level, low) -> IRQ 22 [ 15.527788] wctdm24xxp 0000:01:0b.0: Timeout waiting for receive frame. [ 17.527787]

When I compile dahdi I see these warnings: WARNING: "kasprintf" [dahdi-linux-2.5.0.2/drivers/dahdi/wctdm24xxp/wctdm24xxp.ko] undefined! WARNING: "kasprintf" [dahdi-linux-2.5.0.2/drivers/dahdi/dahdi.ko] undefined! And "modinfo dahdi" shows that the driver was built for a 2.6.17 kernel, SMP mod_unload 586 4KSTACKS gcc-4.1 If I "modprobe -a dahdi", I get

I can either get the TE100P working or the 3 X100P clones working, but never both. I have the TE100P connected to a channel bank, and X100P clones to lines from the phone company. This is my zaptel.conf span=1,1,0,d4,ami fxsks=1-24 loadzone=us fxols=25-27 loadzone=us I then do [root@asterix root]# modprobe zaptel [root@asterix root]# modprobe wcte11xp ZT_CHANCONFIG failed on channel

Hi, 1. Is there any manual entry about modprobe's options relative to a given Dahdi driver (wctdm24xxp, for instance) ? 2. When loading a wctdm24xxp driver, is there any parameter to pass to modprobe to configure a span in NT/point to point mode ? 3. After running dahdi_cfg -vvvvv , I can read with dmesg : [ 1986.289277] wctdm24xxp 0000:04:06.0: xhfc: Configuring port 0 span 1 in TE mode

[root@server ~]# modprobe zaptel [root@server ~]# modprobe wcfxo ZT_CHANCONFIG failed on channel 1: No such device or address (6) FATAL: Error running install command for wcfxo [root@server ~]# ztcfg -vvv Zaptel Configuration ====================== Channel map: Channel 01: FXS Kewlstart (Default) (Slaves: 01) 1 channels configured. ZT_CHANCONFIG failed on channel 1: No such device or address

Quick and dirty question: for the TDM410P I must use the wctdm24xxp driver? Att Vin?cius Fontes Desenvolvimento Canall Tecnologia em Comunica??es Ltda.

On Wed, Nov 18, 2015 at 6:00 AM, Rowland Penny <rowlandpenny241155 at gmail.com > wrote: > On 18/11/15 10:27, Jeff Dickens wrote: > >> >> >> On Nov 18, 2015 4:35 AM, "Rowland Penny" <rowlandpenny241155 at gmail.com >> <mailto:rowlandpenny241155 at gmail.com>> wrote: >> > >> > On 17/11/15 23:09, Jeff Dickens wrote:

Hi, sorry for my insistence but this is a big problem for me..my steps for remove card are ok ? Thanks. ------ Salvatore. ----- Original Message ----- From: "Sasa" <sasa at shoponweb.it> To: <asterisk-users at lists.digium.com> Sent: Monday, November 26, 2007 4:25 PM Subject: [asterisk-users] Remove a TDM Card > Hi, I would like remove a Digium TDM2400P from

The TDM410P doesn't support 'hvac', only the obsolete TDM400P supports that option was for the old phones that have a neon light (or equivalent LED+ZENER ciruit). Are other phones off the TDM410P (other than the VTECH) working, or is the Vtech the only model with VMWI available to you. I'm not able to check at the moment, I have copied the asterisk-users list, someone else may

section 13.3.2 of the HOWTO shows that i can add a user to a group with the following command: root# net rpc group addmem "MIDEARTH\Engineers" ajt -Uroot when i execute this command (replaced with my server specific values, of course), i get a NT_STATUS_NO_SUCH_USER error. i can verify that my user DOES exist and that he belongs to the posix group account. i can also verify that the

Hi, I'm running FC3 with kernel 2.6.11. All the binary files and zaptel kernel modules is not available to system at boot time. They are extracted in a ram disk at system startup and then zaptel modules are loaded manually and so on. I have no problem with this boot routine and i've been tested all digium cards (expect tdm24) and they work fine till now. The problem appeared when i