similar to: Cisco 79xx and SIP 7.5 Problems

Hi, I have got my setup almost how I would like it now, but I have just two last remaining issues that I cant seem to find answers too so i'd be grateful if someone could help? 1) Since upgrading my Cisco 7960 SIP phone to P0S3-08-2-00 the phone now displays the IP address of my asterisk server alongside the caller ID of the incoming call. For example "0123456789@192.168.0.1",

I have one use on our PBX who has been experiencing seemingly random disconnects. The user is on the same LAN as everyone else, using the same type of phone (79XX loaded with SIP firmware) as everyone else. He had some disconnects a few weeks ago, I suspected the phone, so I swapped his with mine. I have since not had issues with his old phone, however, he has had issues using mine. So, the

Hi, I am upgrading a Cisco 7960 phone from SIP V.5.1 to 6.0 and then will to go up to 7.5 However in my first attempt to go from V.5.1 to 6.0 this is hat happens: - The phone reboots - The phone then reads the file OS79XX.TXT from the TFP server. In the file I added the version "P0S3-06-0-00" - It starts upgrading firmware - Then I get the following message: (Upgrade Failed -

Boy oh boy. This blows. I upgraded to 1.2.2 from 1.0.9, and of course had the timebomb bug. Immediately after upgrading to 1.2.3 we were ok, for 24 hours or so. Since upgrading to 1.2.3, though, the whole system has locked up twice. Once on Thursday, and then about a half hour ago. The server would reply to a ping, but no ssh login, no local console login - just locked up. This ain't good for

Is there anyway to force an autopickup on a cisco 7940 / 60 from the dialplan ? My problem is that I am originating a call from the AMI, with the internal user being called first, and then connecting to external user. However, sometimes the internal user doesn't pick up the phone, so the call is never placed. I need to know the results of the call so I need to be able to either a) get

Hi, I am new to Asterisk and have some general questions _before_ I start buying equipent to install and get everything up-and-running. (this means I have no running Asterisk (yet)). I have read already a lot of doc, but some things are not clear to me, since I'am inexperienced in Asterisk and PBX. The goal: Make PBX using Asterisk and Cisco 79xx equipment for 25 phones (1 x 7970, 4 x 7960,

Howdy, How can you tell if RTP traffic has been reinvited/is bypassing an * server? Sincerely, Brent A. Torrenga brent.torrenga@torrenga.com Torrenga Engineering, Inc. 907 Ridge Road Munster, Indiana 46321-1771 +1 219 836 8918 x325 Voice +1 219 836 1138 Facsimile www.torrenga.com

Has anyone had problems getting their preffered codecs on the Teliax web interface taking effect? I have two accounts, two separate yet similarly configured * servers. On one account the settings took right away - on another server I am getting no result. In fact, no matter what I change the settings to, only the old codecs are usable (otherwise * says it can't negotiate a codec). Teliax

Dearest List, I guess I missed this point: Is it true that if you change the echo canceler in zconfig.h, and then recompile/install your zap modules, that for this to be taken into effect by * you must then recompile/install *? I would have figured that the zap echo cancellation method was independent of *, and I don't recall seeing any docs mentioning either way. Sincerely, Brent A.

Is it possible to dial more than one extension with a different CID to each extension? I'm thinking macros might be needed, but I don't have a good handle on macros. Is it possible? Any hints? BTW - this would be used for showing an internal extension to one phone and a PSTN accessible number to another phone. Sincerely, Brent A. Torrenga Torrenga Engineering, Inc. 907 Ridge Road

Howdy: Does echo only occur on analogue PSTN lines, or can it also occur on PRI and BRI lines? If so, for the same reasons? This is a part of our consideration to transition to BRI. Sincerely, Brent A. Torrenga brent.torrenga@torrenga.com Torrenga Engineering, Inc. 907 Ridge Road Munster, Indiana 46321-1771 219.836.8918x325 Voice 219.836.1138 Facsimile www.torrenga.com

I am trying to use a the SIP tapi from www.enum.at <http://www.enum.at/> . This works fine from all kinds of applications which support TAPI, like outlook and Dialer Pro. However when making tapi controlled calls, the signaling to and from PSTN seems to fail. I have used the digium hardware ISDN PRI boards, but also a SIP gateway. Both result in a audio message from asterisk

I am thinking of turning on the NAT option in our Cisco phones (and the corresponding sip.conf modification) to allow the phones to be taken outside the LAN. Can anyone think of any reason not to just always turn on the NAT enabled option? I can't think of a reason not to always operate these phones with this enabled, since it would likely allow them to be taken outside our LAN and used.

Hola, What would a valid regexp in Asterisk be to identify a NANP number, i.e., NXXNXXXXXX? Sincerely, Brent A. Torrenga Torrenga Engineering, Inc. 907 Ridge Road Munster, Indiana 46321-1771 tel:+1 219 836 8918 x325 fax:+1 219 836 1138 email:brent.torrenga at torrenga.com web:www.torrenga.com

I think A@Home allows a user to search a directory by either first OR last name, right? I don't know for sure since I don't run A@Home. I would like to offer that functionality in my system - and I'd have done it by now if there was a prompt where Allison asks "press 1 to search by first name, press 2 to search by last name". But I don't think that prompt exists. Can

Hello, we got a SNOM 360 here and this gota TRANSFER button. With this i can transfer a call from my phone another one. But when i push this Button and transfer the call to another phone, i get kicked out. Now, every secretary first asks the chief if he is available or not - how can i implement this feature thx for any ideas !

Out internet connection was out this morning. It seems that the SIP extensions on our LAN were affected. Behavior like: Call comes in over POTS to a TDM400P, there is a delay then before the Cisco 79[46]0's start to ring. If we were lucky enough to get a call through, then we could not transfer the call, or place the call on hold, or park the call. Outbound calls seemed to have a delay

Does anyone have a good resource to learn how to program the soft and hard buttons on a Cisco 7940 or 7960 phone? Using SIP Firmware...thanks. -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20060303/e5e63834/attachment.htm

We are looking to lose the TDM400P in favor of an ISDN-BRI solution. This should get rid of static on the line (at least any static generated by our half of the circuit), right? I am a total virgin to ISDN. I understand that we need two BRI circuits to provide four voice channels, and that the hardware to speak to the BRI circuits can be passive or active, with the active type being much more

Hello! Is there a phone compatibility list anywhere? I know Asterisk is supposed to be compatible with IP phones that support SIP, h.232, and IAX, but a list of phone known to be supported would be a nice addition to the documentation. I need a buisiness phone, and the Cisco is _EXPENSIVE_ I like the 3com 1102, but it is NBX phone, and I can find no documentation of this phone working