Displaying 20 results from an estimated 10000 matches similar to: "Multiple TDM400P's in a single machine"
2006 Mar 23
6
Stability of Asterisk with 2 x TDM400P cards (6 analogue lines)
I would like to hear from anyone good or bad as what their experience has
been in recent times with STABILITY of current builds of Asterisk and
drivers for TDM400P.
The sort of configuration is: 6 incoming POTS lines. ie. 2 TDM400P cards.
I am not concerned with: price points, or the advantages or disadvantages of
using POTS vs ISDN technology, but simply RELIABILITY & stability of the
2007 May 03
3
FXO recommendation
Hi all,
With the gamut of FXO cards out there, I'm looking for a recommendation for
home use. I have a nicely working Asterisk 1.4 system that just requires an
FXO card to connect my NTL PSTN to it. My previous X101P clone seems to have
kicked the bucket.
Any suggestions would be greatly appreciated.
Regards
Kyle
--
Kyle Gordon
kyle@lodge.glasgownet.com
http://lodge.glasgownet.com
2007 May 28
2
Multiple TDM400p cards in one machine -- no longer an issue?
Hi all,
Years ago, I was pretty sure attempting to use two TDM400p cards in one
machine was recommended against by Digium ... probably because the cards
couldn't hack it, and/or interrupt problems etc
I have seen some posts recently that seem to indicate it is in fact possible
these days thanks to some updated firmware perhaps? ..... I just need to
have two in the server because the 4 ports
2008 Mar 27
3
problem about voice when using TDM2400p with VPMADT032 echo canceller module
hi you,
I'm having problem with voice quality on my trixbox using TDM2400B.The trixbox is connected via 20 FXO ports on a TDM2400 with the hardware echo cancel module. Echo cancel almost works, but the users hear what they describe as a 'background crackle/buzz' coming back when they talk.
anyone have the same problem? pls help me. thanks a lot.
my trixbox and config
2005 Feb 14
3
Digium Cards connecting to BT
Hi there
Just a general question, has anybody experienced any problems with any
Digium telephony cards in the UK, specifically with BT (British Telecom)
lines. I just want to make sure there are no compatibility issues before
purchasing cards, (mainly TDM400P's)
Any comments would be greatly appreciated
Thanks
2004 Nov 23
7
Unable to open master device '/dev/zap/ctl'
I installed TDM400P and X100P pci cards in a system running mandrake 10.1
official, kernel 2.6.8.1-12mdksmp. I can compile zaptel, libpri, asterisk
and modprobe (zaptel, wcfxs, wcfxo) without errors. Except that running
ztcfg and asterisk fails.
[root@asterisk asterisk]# ztcfg
Notice: Configuration file is /etc/zaptel.conf
line 3: Unable to open master device '/dev/zap/ctl'
2006 Mar 27
3
Dell 2850 w/TDM2400?
Does anyone know if a TDM2400 will fit into a Dell 2850?
Kerry Garrison
Director of Technical Services
Tech Data Pros - Orange County's Mobile IT Service Provider
(949) 502-7819 x200 - <mailto:kerryg@techdatapros.com>
kerryg@techdatapros.com
<http://www.techdatapros.com/> http://www.techdatapros.com
-------------- next part --------------
An HTML attachment was scrubbed...
2006 Oct 16
7
tdm2400p question
Hi all,
I'm confused, in digium website, it says:
TDM2400P: It supports a combination of up to 6 FXS and/or FXO modules for a
total of 24 lines.
6 plus 6 is 12, how come it's 24?
if I have 24 PSTN lines, i'll be needing 24 FXOs.
Pls. elaborate.
thanks.
Lito
-------------- next part --------------
An HTML attachment was scrubbed...
URL:
2005 May 06
4
3 x TDM400P in one PC ??
Hi Folks,
Does anybody have experiences with plugging 3 TDM400P cards in one PC??
I think about a Asterisk box handling 8 incoming analogue lines and providing
4 lines to an old analogue PBX.
I read a lot about trouble with the TDM400P cards so this idea seams to be not
really god, or?
Ciao
Joerg
--
_____________________
Don't PANIC
2004 Oct 06
4
TDM400P stop responding
iH
have a TDM400 w/ 1 FXS & 1FXO card. after about a day or so the FXO
stops working. after a reboot i get the following error. to get the
card working again i have to shutdown, physically unplug/replug the
card (reboot only, power off/on does not work) any ideas what may be
going wrong here?
thanks
- hcir
Zaptel Configuration
======================
Channel map:
Channel 01: FXO
2006 Jun 04
5
WCTDM-24xxp woes
I am currently running Asterisk 1.2.8, on an AMD Sempron 3100+ (ASUS K8N
Nforce based board). I am using a Digium wctdm24xxp to terminate 8 (2x
quad) FXO lines. Using ztmonitor (From zapata) I cannot see that there is
any registerable incoming volume from these lines. I've been running them
at rxgain = 25 (zapata.conf) to make the audio audible, however this
creates poor call quality issues
2005 Jan 31
2
Dialing out on TDM400p 4 port FXO
Hi,
I have two small companies that are going to be sharing a * box. I have 2
TDM400's with 4 fxo ports each.
Each company has its own sales person and they would like the sales people
to always show their own caller id and have their own lines ring directly to
their phones. Company 1 sales person uses the 1 port on the tdm400 and
company 2 sales person uses the 2nd port of the tdm400.
2005 Jun 04
4
X100P installed OK, after added TDM400P Asterisk would no longer start
Hello
I setup Asterisk@Home with purely VoIP and it worked fine. I then added an
X100P card so I could call out / take inbound calls via PSTN and that went
fine. But I have just added a TDM400P card (specifically a TDM30B) and now
problems.
Here is some of the output. Any ideas on what I should be looking at next?
When I run genzaptelconf -s -d I get lots of erors on screen - bit I can
2009 Mar 04
1
Question on phone line "pass through"
Hi all,
I have a TDM2400 full of FXS cards and a TDM800 full of FXO cards.
If I have a fax machine on the FXS port dialing out through asterisk
on the TDM800 FXO, should I be expecting any problems?
Or should this just work as expected? (ie, flawlessly with the
asterisk box essentially transparent to the whole operation).
I am doing it this way to allow many faxes and modems to share a dial
2004 Sep 16
1
Static noise and server locked when using two 4FXO tdm400p pci cards
Hello all
We have tested for a mounth or two an asterisk PBX using one T1 channel
bank with 24 fxs and one TDM400P digium card with 4 FXO modules.
This worked with minor problems, the most notorious being some sporadic
static noice or failure in the first FXO module on the wildcard.
Now we have a client with 12 pstn lines and 48 extensions and we are
trying to deploy an Asterisk PBX server
2008 Apr 12
2
X100M never goes on-hook state
Hi guys,
I've been experiencing a very strange issue with my Digium Card TDM400
as of this week. It has two FXS and two FXO.
The FXO modules (both of them) never goes on-hook after hanging up in
Asterisk. It had worked perfectly well for over four years.
I put an ammeter in series with the line and the card, and immediately
after plugging the connector to the card, I got 26mA in the circuit
2004 Aug 25
7
TDM400P lockups (FXO)
Hey all - we have two TDM400P cards in an SMP Redhat9 box, with 4 FXO
ports each running thel latest Asterisk CVS.
Users connect to this to share POTS lines using analog phones connected
to Sipura SPA-2000 boxes. All works reasonably well, except every day
(or more) a line will get "locked up". No other way to describe it
really -- the line just stops working, so if someone tries
2005 Feb 09
2
Problem using TDM400P FXS card
Hello, everyone
After having spent several time to look for any
solution for my problem, I decided to write here.
Here is the problem got a Digium X101 FXO card and
Digium TDM400P alias freshmaker (1 fxs module on it on
first port ) in my asterisk box. The X101 works
perfectly.
The problem comes from the TDM400, when i plug a
tested working phone on it , i get no dialtone; the
goal is to
2006 Jan 30
5
How many TDM2400P's will a server take?
How many TDM2400P cards can I safelly install in one PC? I'm loking for
answers from whoever has a working scenario with * and a number of cards
higher than one.
Thx,
Juan
__________________________________________________________
Mensagem enviada usando o Webmail da ViaLink ver. 2.7.8
2006 May 01
3
Digium TDM400P vs Sangoma A200 for 2 x FXO
Evening all.
I'm looking at building an Asterisk system for one
of the projects of the Charity where I'm the
SysAdmin.
The project has two analogue phone lines - BT
Featureline Compact, we're in the UK - that I'd
like Asterisk to handle.
My current quandary is which FXO interface to use.
I've been looking at the Digium TDM400P and
Sangoma A200, which are similar prices for