similar to: sipura 3000 and other probs

Can anybody show me a working Sipura 3000 setup please? I need to setup one to my * box, ... What are the variants you can setup? Advantage - disadvantage. bye Ronald Wiplinger

Dear all, I am wondering why the step() procedure in R has the description 'Select a formula-based model by AIC'. I have been using Stata and SPSS and neither package made any reference to AIC in its stepwise procedure, and I read from an earlier R-Help post that step() is really the 'usual' way for doing stepwise (R Help post from Prof Ripley, Fri, 2 Apr 1999 05:06:03

Hello, After poking and prodding at Asterisk and Zaptel for over a couple years now, I've dedicated some time to actually reading the code and trying to figure it out. It's been fascinating. With the driver source on one part of the screen and a pdf of "Linux Device Drivers" on another part I've aquainted myself with device driver programming and the interesting

I was wondering if it is at all possible to run more than one instance of icecast? I tried installing a 2nd instance of icecast (folder name icecast2) and adjusted the xml files to accommodate a 2nd port but it doesn't seem to be working. I should add that outside of port 8080 (the apparent default), icecast has failed to work for me. (I am quite well aquainted with forwarding ports on

I am trying to configure the FXO port on a Sipura-3000 for use with Asterisk. When I connect to the Sipura to dial out on the PSTN line connected to the Sipura's FXO port, it gives me the dialtone of the PSTN line and then I can hear the DTMF for the number I dialled beforehand. It does work but the customer perceives this delayed second DTMF feedback as "unprofessional" and the

Hi, the topic says it all really. Does the Sipura 3000 detect and report UK clid correctly? thanks Mike

Does anyone have a Sipura 3k running, and using the FXO? I've got things working right, but if I try to toss a *67 in the dialplan, it seems the sipura is throwing a 403 forbidden back. For example: exten => _91NXXNXXXXXX,3,Dial,SIP/sipura1pstn1/${EXTEN:1} works fine exten => _91NXXNXXXXXX,3,Dial,SIP/sipura1pstn1/*67${EXTEN:1} does not (even if I toss a couple Ws in) I can't

Hi all, We have several sipura 3000's working well for outbound calls, however the issue we have is that when calls are sent to the Sipura with Dial(SIP/${EXTEN:0}@sipura1) the Sipura does a SIP answer immediately and then proceeds with the call "in band" therefore sending dialing sounds back to the caller. Other SIP gateways we have notably the Vegastream and others do not do a SIP

Hi I wonder whether anyone got the Sipura ata 3000 to decode British Telecoms callerid and pass it to asterisk? The userguide seems to suggest that this is not possible, is that right? Conrad

Hi all, Anyone able to remotely reboot their password protected Sipura SPA-3000 from command line. I am trying: Sipura SPA-3000 from command line: # wget http://admin:mypassword@192.168.1.55/admin/reboot The strange thing is it works fine when I go to http://admin:mypassword@192.168.1.55/admin/reboot with my web browser... Thanks....

May be I have fiddled too much with my sipura settings but I can't get it to give the stutter tone when there is a new voice mail waiting on the asterisk box. I can either get a stutter tone all the time or not at all. Anyone got this working. Thanks Chris

Folks! I discovered some serious problem with several Sipuras 3000 but I don't know if the problem is with them or Asterisk. Basically, if I call a Sipura PSTN line, when there is a call already in progress, generally I get a 503 Sevice Unavailable, but if I try hard enough, I am able to get through and connect to dialed number. The other call gets disconnected but the originator of the

If I have multiple Sipura 3000 device how can I dial out properly? I can receive call without any problem and that's working really well. Caller ID is shown and when someone call he get's the welcome message the same way I have it configure with the X100P card. I don't seem to have any echo problem with the Sipura 3000 (but I do with X100P cards) My main concern is for

Hallo! I had ordered a Sipura SPA-3000 in the UK, but the supplier turned out to be unreliable and never shipped. Yesterday I went looking for alternative suppliers and found the Linksys SPA3000 device. It's a different box, but the specs look very similar. Is this the same device? Has anyone used this Linksys SPA3000 successfully with Asterisk? Thanks, Frank

I have three Sipura 3000 FXO untis for incoming PSTN lines on a small pbx. There is an IVR to select the extension. The DTMF tones are not being sensed so the IVR does not work and incoming calls are not being answered. I have listed my sip.conf entries. Is there any solution to this? ;Sipura units [101] type=friend host=dynamic context=default secret=mysecret mailbox=101 dtmfmode=inband

How can I dial *67 on a Sipura 3000 if I dial from a SIP phone connected on an asterisk server. I always get a message saying that authentication failed for INVITE for sip221@192.168.1.6. If I dial a number without doing *67 it's working fine... sip 221 being the extension of my Cisco phone and 192.168.1.6 being the IP of my asterisk server... I have my outgoing context configure

Hi all, I was wondering whether anybody here would help me clarify this minor issue please. If I have the following setup; Asterisk ------ Sipura SPA 3000 (fxo) --------- Pstn Line Would a call coming in on the pstn line be answered by the ATA or just get passed through to the * server (depending on dialplan) to handle? So basically, the caller does

Does any body know if it is possible to group SIP channels just like it is possible with Zap channels? I have a group of FXO gateways (Sipura 3000's) and I would like to treat them as a group the same as I would Zap channels. Does anyone know if this is this possible?

Dear list, I am playing with Sipura 3000 since last week. Through the wiki pages I could get running it reasonably well. My setup is that of a Sipura, linked with a local analog cordless phone, a local PSTN line and the setup to link to an asterisk server located at a remote static ip address. I can dial the cordless phone from other extensions located at the asterisk server; I can dial out

Hi All, I am using a Sipura SPA-3000 as an FXO gateway to bring calls in and out of Asterisk. I am using "PSTN Ring Thru Line 1" (on the "PSTN Line" tab) so Asterisk answers the call rather than the SPA-3000. It is all working perfectly except I can't get the SPA-3000 to pass caller ID to Asterisk. It passes "Display Name", "User ID" and any "PSTN