similar to: TDM 400 FXO FXS Test

Hi Mary Christmas to y'all ! I am trying to configure * with one TDM and one ISDN and Bri-stuff, all is ok with only TDM but when add ISDN I get following error: I have tried to switch fxs/fxo but then I get error also without ISDN, card is configured from Digium with FXS(green) modules are closest to the bracket. ZT_CHANCONFIG failed on channel 1: Invalid argument (22) Did you forget

I'm looking for a zaptel type device with one (or more) FXO and one (or more) FXS port. Basically this guy would sit in-line of your phone line (PCI card). Any suggestions? TDM400 would be overkill. -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20050515/d66e6335/attachment.htm

I have put a box together using 2 X100P and 2 TDM400 4port cards. Using the simple setup that Martin posted a few days ago, I have asterisk almost up and running. /etc/zaptel.conf fxsks=1-2 fxoks=3-10 loadzone=nz defaultzone=nz (I have added NZ tone information to zaptel and Asterisk - I'll submit a patch soon). /etc/asterisk/zapata.conf [channels] context=incoming signalling=fxs_ks

Hi, I'm just starting out with Asterisk, in combination with a TDM400, filled with 2 FXS on channels 1 and 2, and 1 FXO on 4. Having just started, all I want right now is to be able to answer incoming calls on a phone connected to channel 1. The trouble is the caller id. I have caller id enabled on my line, my phone supports it, and when I connect the phone directly to the line, it works.

We're having issues with the FXO/FXS ports on our Digium TDM cards sporadically. I'm wondering if anyone else has had these problems, or if anyone can provide guidance diagnosing or fixing the issue? The symptoms are that the FXO and FXS ports "stop working", usually after 2-4 weeks of server uptime. When this happens, sending a (SIP) call to an analog phone on an FXS port

A bit about my experience with the TDM-04 FXO. Only saw a few post on this subject, thought I would contribute a little about my experience to save others the hassle. a. As an earlier poster noted, the driver for the FXO is in the wcfxs module. Perhaps it should be renamed to something less confusing. b. You need the zaptel,zapata libraries from the cvs, the ones with Asterisk 0.7.2 won't

Im having a problem getting the 2 cards working together. I added the TDM with 3 FXO and 1 FXS board. The TE405p is working fine. THe TDM registers and identifies the FXO's and FXS but cant get them to go off hook. I hope someone can help. Asterisk seems to THINK its dialing it sends manager status as dialing, and it just sits there with no tones, on the phone dialing out. If I dial,

Hello, everyone After having spent several time to look for any solution for my problem, I decided to write here. Here is the problem got a Digium X101 FXO card and Digium TDM400P alias freshmaker (1 fxs module on it on first port ) in my asterisk box. The X101 works perfectly. The problem comes from the TDM400, when i plug a tested working phone on it , i get no dialtone; the goal is to

Please explain the relationship between modules from the driver (wctdm), the /etc/zaptel.conf file and zapata.conf. Specifically, if I have a FXS module 0 and FXO module 1, what should be used in zaptel.conf and what should be used in zapata.conf? Then finally, in extensions.conf, what is the Zap channel for dialing out? Zap/? % dmesg Module 0: Installed -- AUTO FXS/DPO Module 1:

My TDM400/zaptel 1.2.10/Asterisk 1.2.13 suddenly stopped bridging outgoing FXO calls. If I make a call (from an FXS channel) to a PSTN destination, and the other side answers, Asterisk will show continued ringback on the FXS channel, while the PSTN side hears silence. No error message appears. If a call from PSTN terminates on the same FXO, Asterisk can still ring the FXS channel, and when

I've been having trouble with making outbound calls to my TELCO from a TDM400 card (FXS KS signalling) after upgrading from 1.6-beta9 to 1.6.0. The problem is completely intermittent. When it fails, I get this message: [Nov 9 19:12:26] WARNING[18916] app_dial.c: Unable to create channel of type 'DAHDI' (cause 0 - Unknown) At some point, it starts working, but I don't know what

Hi all, I have hit a wall configuring a TDM400, I have set these up before without issue but today I just can't seem to figure out what I am doing wrong. On an incoming call the following is produced in the Asterisk console with verbose 4 -- Starting simple switch on 'Zap/2-1' Mar 22 16:12:34 NOTICE[2051]: chan_zap.c:6063 ss_thread: Got event 18 (Ring Begin)... Mar 22

Well, I thought I had my problem solved, but it is acting up again. Hopefully this time I can provide enough information. What I have is an * box setup with one X100P and TDM400 with one FXO and one FXS. For my regular setup with interfacing with my PSTN and my entire house with analog phones, the box is working great. I am trying to interface a Mediatrix 1202 device to my * box via the

Folks, I have a TDM400 with an FXS module. I'm having some trouble ringing some phones attached to the device. I have a real el cheapo handset that cost me about 9UKP. It works fine, I plug it into the Wildcard and call the channel and it rings. I have tried plugging in my BT Diverse 3016 cordless phone but it will not ring, although I can call out from it. I have also tried my GPO 332L

Hi. I have been searching through old threads and various forums, but can't seem to find out what the consensus view is here on the best type of FXO hardware to use for a home asterisk implementation. Specifically, should I buy a FXO ATA like the Sipura 3000, or a PCI form factor port like the Digium TDM400 series. I have read horrible things about problems with the X100P, so I have ruled

Hi On an old IBM Netvista thinclient, the TDM card doesn't detect incoming calls, although the card seems to be detected, and correctly configured: pbx asterisk # lspci 00:03.0 Communication controller: Tiger Jet Network Inc. Tiger3XX Modem/ISDN interface # cat /etc/zaptel.conf fxsks=1 loadzone=fr defaultzone=fr # ztcfg -vv Zaptel Configuration ====================== Channel map: Channel

I just installed an FXS module onto a 4 channel tdm thats about 5 years old and it wont work. Running dmesg I can see the following error: Zapata Telephony Interface Registered on major 196 Freshmaker version: 71 Freshmaker passed register test !!!!!!! LOOP_CLOSE_TRES iREG 1C = 1 should be 1000 !!!!!!! RING_TRIP_TRES iREG 1D = 8000 should be 3600 !!!!!!! COMMON_MIN_TRES iREG 1E = 0 should

Hi- I'm totally stumped configuring my TDM400P with one FXS and one FXO module. Before I got the FXO module, I used to have an X101P, and everything was working very well. Now * doesn't seem to recognize the FXO channel. I've searched the wiki and the list archives. Stock Debian 3.0 stable installation. Any advice? Thanks. -- David Here's my configuration: modprobe zaptel

G'day all, A weird problem has just started happening with my * server, and I've googled myself stupid looking for help. My system is latest CVS, a TDM400P with two FXS modules, two X101Ps, and VoIP connections (SIP, SCCP & IAX2). My wife complained about her extension (analogue, on one of the TDM400 ports) being dead -- no dialtone. I had to shut down *, then unload and reload the

Hi all, I bought a Sangoma A200 card from an online supplier and explained exactly what I wanted, 3 incoming phone lines to PBX and a life line (some where to connect a standard BT phone to the PBX incase the power goes, making the BT phone ring). I was told to order 1 x FXS module (2 FXS ports) 2 x FXO modules (4 FXO ports) However being a complete noob, I have connected the 3 lines to the