similar to: feedback on grandstream budgetone

I am setting up a small Asterisk system for use at home. I have one Budgetone 101, one Cisco 7960 and two Xten lite softphones. So far everything is working expect for an issue with the Budgetone. When a call is placed between the Budgetone and any other phone, the call is setup and sounds good. If I hang-up on the Budgetone, everything is ok. If I hang up on the other phone, the Budgetone

Hello guys, I ask you to share your experience with your BudgeTone 100.... I have my asterisk @ work and I've bought a GrandStream BudgeTone (SIP phone) and I usually use X-Lite I have plugged my BudgeTone into my home network because I want to be called even at home. I succeed to register my X-Lite with Asterisk from home but I can't do that with my BudgeTone. (I don't know

Hi I am setting up an Asterisk System in an office environment, Incoming and Outgoing calls are working ok, but i am having a few strange problems regarding call waiting. With the SNOM 200 (firmware 2.02t) phones, if you are on a call and a 2nd call comes in, the call waiting beep is played and the light flashes, but if you hang up the 1st call, instead of the phone ringing, it connects the

I have two problems with Asterisk and my Budgetone 100s. 1. Sometimes when outside callers dial my Budgetone it will ring twice, then the caller will receive a busy signal. This happens intermittently and I cannot pin down the circumstances of when it works and when it doesn't. Asterisk logging doesn't give me too much info when this happens: *CLI> -- Executing

Does anyone know what the Grandstream Budgetone is going for $$$ in the US? I didn't immediately see pricing on the phones page. AJ

Symptom: Phone after about 15mins will stop functioning Problem: DHCP lease renewed but default route dropped Fix: Assign a static ip and problem is resolved. Upgrade to new firmware once it is released It turn's out that these phones have a few issue in 1.0.3.81 firmware. The phone may stop transmitting packets if configured with DHCP, if DHCP is being provided by certain devices. Netopia

Has anyone seen/dealt with the Grandstream BudgeTone-100 producing double dialing with asterisk? Thanks JDT Example: (password input = 101) -- Playing 'vm-password' -- Incorrect password '11001' for user '101' (context = <any>) -- Playing 'vm-incorrect' -- Playing 'vm-password' -- Incorrect password '110011' for user

I have a client using a Grandstream Budgetone 102, but he is unable to register to my Asterisk server. About every 20 seconds, I get the following messages: Aug 11 11:27:17 DEBUG[1087740720]: chan_sip.c:748 __sip_autodestruct: Auto destroying call '3b4b68ec48200ab9@192.168.xxx.xxx' Aug 11 11:27:19 NOTICE[1087740720]: chan_sip.c:7336 handle_request: Registration from

Is anyone using this combination successfully? I have a dell 500sc running rh9 and asterisk 1.0rc1. It is configured with an x100p. I have a Sipura SPA-2000, laptop with Xlite and a Grandstream Budgetone BT-101. I have signed up with Voipjet (they use iax2). I also have an FWD number via iax2. I can sucessfully call back and forth to all devices via zap, sip, and fwd. I can successfully

I know there are several folks hanging around the list that resell VoIP products, I'd be interested in getting your info off-list as I'm trying to persuade someone to get me a budgetone 101 for Christmas ;) I've checked the yahoo site, and they seem to only carry it in white.. Ideally, I'd like blue, so if you have it, please let me know. Also, I've been watching the list for

Just to toss in my very limited experiences with the Grandstream phone-- I haven't tested it enough to really know nor is my Asterisk config set up enough to fully try all the features. Mostly, it just works. It was very easy to configure and get running. I've been toting it around to clients as a show and tell exhibit and it has helped get people excited about the possibilities. Voice

I bought three plus two Grandstream BudgeTone 101 phones. The shipping cost more than the phone itself from Pulver store. The first shipping had one phone defect. Nothing on the display. (Can happen!) The second shipment had one phone with a defect display, but it still worked. The second phone's handset was defect too (microphone did not work). Changing the handset from this one to the

Hi there, I'm having problems with the Grandstream Budgetone 101 on hangup - "show channels"/"show channels concise" output is still showing the call's channels as active. The problem does not exist when I use SJPhone, so I'm assuming it isn't an Asterisk configuration issue. Has anyone seen this, or better, does anyone have a fix? :) Thanks, David. --

Hello, I have a problem with asterisk and Grandstream BudgeTone-100. With default configuration everything works (in anonymous mode and fixed IP), but if Im trying to enable registering, it dos not work. I used 'sip debug' and verbose level 10, nothing happens if I switch telephone on (no messages about bad auth etc). As I understood, after switching phone on at first it will try to

I've looked through the archives - and see questions similar to mine, but no answers. What, if anything, can be done to get the incoming Caller ID to be presented on the Budgetone's Caller ID display? In all other respects the phone+Asterisk seem to be extremely happy with each other.

Hello! I am considering mass deployment of Budgetones 102. According to their website, remote provisioning (configuration via TFTP) is possible. Anyone has experience with this? Is this really working?

Ronald, Grandstream products have a one year warrantee. If you don't have any luck with Pulver, contact us and we can probably get your phones exchanged. Please don't assume that your experience with Grandstream is typical. We sell a lot of these phones and the overwhelming majority of the purchasers are very happy with their units. The quality has improved tremendously over the last

I have a strange problem in that I have put a budgetone out on the internet that connects to my * server that's behind a firewall. They can call me I can call them and it works fine. However, I have setup a link to sipdiscount on my * server. If the budgetone user calls via my * box to sipdiscount all the budgetone user hears is silence and the called person hears silence as well when they

Just for the record and to possibly help with others who get BudgeTone phones. My asterisk box is behind NAT, and I use Vonage, NuFone, and iconnecthere for my "POTS backhaul." On the front end I have an ATA186, a Digium TDM20, and now a BudgeTone 102. The BudgeTone definitely has issues wrt the RTP stream and NATting, although unfortunately I haven't yet been able to dig

I'm using 1 BudgeTone 100 IP Phone and a Sipura 2000 for all my old analog phones. The analog phones with the Sipura seem to work great. Voice quality is fine on both ends on the Sipura. I'm using the Teliax service and I use the Ulaw codec for all phones. However, I'm struggling with the BudgeTone 100. On my end, I find there is lot's of voice cut outs. I'm told my