similar to: RE: Euro-ISDN

asterisk-users-request@lists.digium.com is believed to have said: >chan_capi does not set the NT-mode. Your cards driver need to do that. >E.g. for Eicon DIVA Server cards, you just set the '-x' option with divactrl >or set NT-mode in the config wizard. >chan_capi does not (need) to know anything about what protocol the card is >doing. CAPI is independent here. Ok.

asterisk-users-request@lists.digium.com is believed to have said: >> While we are at the subject another couple of simple related question. >> >> Are HFC-S cards active? I got one for a very low price, so that I >> imagine it will be NOT the case... > >No, these cards are passive. The protocol handling must be done by >the hosts CPU / driver. OK; price

Hi, I'm looking for an interface card for termination of Euro-ISDN2 (BRI) lines. That is ISDN lines from the telco into my Asterisk box. Any recommendations, good/bad expiriences ? At present I'm looking at cards from BeroNet and Junghanns. Cheers, John Faroese Telecom

Hi, I have to set up an Asterisk with an 4-port BRI card. Hylafax should send and receive fax. Will this work reliable? Any recommandations for an 4-port BRI card? Other alternatives except analog fax units? thanks for your help best regards Thomas

Hello everyone. I need a BRI ISDN card that works in Romania. I already have one of the "Cologne HFC-S" PCI cards and it doesn't work right, it's junk. I get waaaay too much echo using it. I'm now "shopping" for a better card. Can anyone recommend me a card that "fits" the following: (a) Costs less then $1000 / 750 euro (b) Has one or (preferably) two

Hello, I am using a system with an AVM ISDN PCI card (fcpci) and asterisk with chan_capi-cm-0.6. The hardware is connected to a Siemens Hipath 3550 PBX. As a BRI connection has 2 channels and allows 2 simultaneous calls, numbers/MSNs 6391 and 6392 were for provisioned for each channel. The system is working (partly, read on), the trick is the correct cable wiring and setup the PBX's port

Dear all, I'm planning to buying Eicon Diva Server V-BRI for my asterisk server and run with chan_capi. Is anybody using that card ? Would appreciate any feedback. Bartosz

What types of ISDN BRI cards work well in Europe (Guadeloupe, Martinique and France) ? For example: AVM C2 or AVM C4 or eicon Diva server 4 BRI? Any others? Which driver is appropriate? Ray Burkholder ray@oneunified.net http://www.oneunified.net 704 576 5101 -- Scanned for viruses and dangerous content at http://www.oneunified.net and is believed to be clean. -------------- next part

Hi (Armin)! Does someone knows how to identify the type of the card? The delivery note says it is a V-4BRI-8M, whereas lspci reports a 4BRI-8M. What is it really? Are there any Eicon tools to identify the card type? thanks klaus 0000:0a:03.0 Network controller: Eicon Networks Corporation Diva Server 4BRI-8M Rev 2 (rev 01) Subsystem: Eicon Networks Corporation Diva Server 4BRI-8M Rev

Hello All, Has anyone configured bri to answer for only one msn? In essence, when the primary is busy I want to have channel 2 ring. I am using an eicon diva server bri I know I saw it in the windows interface, but don't see it in the linux setup. Regards, Greg

Hi! I have some (short) question about the Eicon DIVA (V-)4BRI cards I want to have (short) answered before buying the DIVA card. I know there are several Eicon guys active on the list, thus I ask on the list instead of directly to Eicon so that all other will benefit as well. 1. Do Eicon DIVA (V-)4BRI cards support TE and NT mode? 2. Can the clock (master/slave) be configured independent

Hi everyone, I have Asterisk SVN-trunk-r7498 running for a few months and I'm quite happy with it. However, I am experiencing a quality issue with my AVM Fritz!card PCI which is used with chan_capi. When somebody calls me on this line he hears a lot of noise and I hear "scratches" and "plops". It is very annoying. Below is is my /etc/asterisk/capi.conf I've tried to

Hello everyone! I've got a Eicon Diva Server BRI card into my "*" box working just fine, but I wander if there's anything I can do to improve voice quality for my operators. I'm thinking something along the lines of "auto gain" and sudden noise suppression (like when you hit a fax machine or the other party accidently touches the dial pad on the phone). Does

Hi Everybody, Has anybody tried the above (or indeed any other 4XBRI cards) successfully with Asterisk. As far as I can see the above mentioned card is an active ISDN card but supported by it's own I4L driver. This leads to interesting questions particularly regarding echo cancellations (which usually doesn't work on the cheap passive cards with one exception as far as I can see).

Are there any step by step instrunctions on how to install drivers and I guess bristuff for this card? Just need to use it to handle voice on 2 BRI circuits (UK) then utilise with Asterisk and some Digium cards handling POTS phones (and some VoIP out the back). It's the EICON card stuff and how to make it all work I'm finding confusing? Steve -- NetTek Ltd UK mob +44-(0)7775 755503

I'm running Asterisk 1.0 RC2 on a RedHat 9.0 box. I have a ISDN BRI line that I would like hook up to my Asterisk server and would like to ask the group what you guys would recommend as far as isdn cards that install easily into the Linux and asterisk environment. Rgs, Mark

I am trying to understand the difference between the divas4linux available from the Eicom/Dialogic website and the melware version. Am I right in thinking that the melware version is for Trixbox or Asterisk but the Dialogic version is for Asterisk only (i.e. will not work with Trixbox?). I've noticed that some of the things mentioned on the Dialogic web site as included with Divas e.g.

asterisk-users-request@lists.digium.com is believed to have said: [setup tool] >Sorry, I cannot answer that one. I don't know enough about these cards and >their drivers. Armin, thanks alot. One has to do some research and experimentation on his own every now and then; and see if there is anything interesting that might even end up in the wiki... ;-) >> So in the end there

Hello everyone, I'm using very simple setup to make and receive external ISDN calls through a softphone (x-lite version 3.0 - Win32) via an asterisk box. Hardware setup: - Dialogic Diva BRI (lspci yields: Network controller: Eicon Technology Corporation DIVA Server BRI-2M/-2F (rev 01)) - ISDN BRI line Software setup: - Redhat 9 - asterisk-1.4.16.2 - chan_capi-1.0.2 Asterisk configuration

Hi, after I fixed my problem with the playback() application, I now have the next strange one. When I dial the number of our client, located in another town, I get a connection to the asterisk server, I can talk to my client or listen to his mailbox. If some in the town of this client calls him, he gets the ISDN error "service not available". Out office is connected to he office