similar to: No IN and OUT on ISDN line at the same

Hello All, I am having an odd problem with Armin's chan-capi_cm on builds higher than 7955. It would seem that this happens on anything higher than 7955. What is happening is the isdn is ringing, then asterisk does a goto-if and just hangs. Asterisk itself is ok, but the isdn then rings out or busys out on the other side. Outgoing works fine, this only seems to effect incoming. I

Hi to all I've mada up my mind and i tried to change from i4l to chan_capi, following some councelling from the gurus. I compiled it up, and when i try to load it in modules.conf, i get that wonderful message and Asterisk does not start: [chan_capi.so]Feb 17 09:21:40 WARNING[16384]: loader.c:239 ast_load_resource: /usr/lib/asterisk/modules/chan_capi.so: undefined symbol: ast_get_group Feb

Hi, I would like to implement a inexpensive home PBX with Asterisk. I have an internal ISDN bus with 6 ISDN phones. I now thought, I connect a Fritz card to my Mehrgerateanschluss (Point-to-Multipoint) supplied by my provider and a second Fritz card to the internal bus. Will this work? Thanks for the help, Arik

Hi all, I would like to announce the first release of the chan_capi channel driver on sourceforge.net The package is available for download with name chan_capi-cm-0.5 and is the current CVS HEAD. It is derived from the chan_capi-0.4.0PRE1 of kapejod. The main changes are: - complete rework - fix race-conditions - fix call state handling - rework of debug/verbose messages - added capiFax

Hello, These are error messages I get when I try to call a number over CAPI channel. -- Executing SetCallerID("SIP/xlite1-3b80", "0") in new stack -- Executing Dial("SIP/xlite1-3b80", "CAPI/hfcpci/b17") in new stack > data = hfcpci/b17 > capi request for interface 'hfcpci' == hfcpci: Call CAPI/hfcpci/b17-1 (pres=0x00,

Hello configuration as follows, dial-out works: capi.conf: [hfcpci] ;;PointToPoint (55512-0) isdnmode=MSN incomingmsn=* ;msn=61 controller=1 devices=2 context=incoming extensions.conf: [incoming] exten => _XX,1,Playback(demo-abouttotry) exten => _XX,n,Dial,SIP/xlite1 exten => _XX,n,HangUp When call is placed, the following debug info is shown, after the last line, it stalls until

Hello, While upgrading * from 1.0.9 to 1.2.5, I have installed chan-capi-head and I can't start asterisk under asterisk group "asterisk -vvvvgc -U asterisk " and "asterisk -vvvvgc -U asterisk -G dialout" work well but "asterisk -vvvvgc -U asterisk -G asterisk" fail. I am thinking about a group permission configuration but I have exactly the same one

Hello Armin, hello List I'm trying to get chan_capi working with asterisk from debian stable (asterisk 1.0.7, the debian version number is 1:1.0.7.dfsg.1-2). I managed to get it compiled by providing my own version of ast_copy_string. This is an Austrian PTP line. I can do outgoing calls fine (no comprehensive tests yet). For incoming calls, I'm getting "No answer" on the

Hello, I just received a couple SX440isdn phones and was wondering if they can be plugged into a Diva 4BRI port in NT mode and work with asterisk+chan_capi? I know they probably work fine with mutliHFC cards with either bristuff of chan_misdn but since I have some spare Divas, I was curious about their potential as phone ports. The Diva's 3 and 4 ports are already set to NT mode at boot

Armin, I am running 1.2.7.1 with an Eicon T1 board version 2 on Debian 2.4 I don't know the details on chan-capi / CAPI drivers. We did the install April of this year. How can I tell what I have? Thank you for your time. Tim -----Original Message----- From: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com]On Behalf Of Armin Schindler Sent: Wednesday,

I've the following setup : sip phone -> ser (auth and routing) -> asterisk with capi isdn when I call a pstn number everything works fine, but I can't hear anything till the called answer. this is the output from a test call : -- Executing Playtones("SIP/2.7.184.61-08152880", "dial") in new stack -- Executing Dial("SIP/2.7.184.61-08152880",

Could someone please comment on the current state of chan_capi, chan_misdn and chan_modem channel drivers in terms of functionality and stability. Specifically, which channel driver would be best for a passive PCI HFC or W6692 ISDN card. The chan_misdn wiki claims that chan_capi distinguishes between junghanns and non-junghans cards, and that chan_misdn is better suited for general misdn

Hi! I'm looking for someone who has successfuly setup an asterisk in austria with isdn in p2p mode and chan_capi. There is is a special problem in austria with DID. If someone is dialing the phone number of the asterisk pbx like 12345-0, zero is passed as an DID, but in Austria u can dial 12345, and the DID which is passed is empty. It seems that asterisk cant handle this. Any ideas?

O.K. thanks a lot, Felix and Peer Oliver. But somehow asterisk keeps telling me while startup: [chan_capi.so] => (Common ISDN API for Asterisk) Jan 24 14:30:47 NOTICE[9796]: chan_capi.c:3271 load_module: Unused contr1 Jan 24 14:30:47 NOTICE[9796]: chan_capi.c:3271 load_module: Unused contr2 Jan 24 14:30:47 NOTICE[9796]: chan_capi.c:3271 load_module: Unused contr3 Jan 24 14:30:47

Hello list! I have a Asterisk 1.2.10 running using the package from Backports.org for Debian Sarge. I have setup chan_capi (0.6.5 from Backports) and it seems that I am only able to use on B-Channel. When trying to place the second call I get: CAPI INFO 0x34a2: No circuit / channel available capi info shows: Contr1: 2 B channels total, 1 B channels free And capi.conf is: [ISDN1]

Hi! I have some (short) question about the Eicon DIVA (V-)4BRI cards I want to have (short) answered before buying the DIVA card. I know there are several Eicon guys active on the list, thus I ask on the list instead of directly to Eicon so that all other will benefit as well. 1. Do Eicon DIVA (V-)4BRI cards support TE and NT mode? 2. Can the clock (master/slave) be configured independent

hi all, i have a probably very stupid question/problem. for testing purpose i am trying to get asterisk running with two isdn cards. I'd only like to here the demo sound when i call the number - but nothing works. The output of show channels is not showing any channel - should there be 4 channels ? - capi info shows my two cards perfectly. The ISDN Controller's are attached to an PTMP

Hi everyone, I have Asterisk SVN-trunk-r7498 running for a few months and I'm quite happy with it. However, I am experiencing a quality issue with my AVM Fritz!card PCI which is used with chan_capi. When somebody calls me on this line he hears a lot of noise and I hear "scratches" and "plops". It is very annoying. Below is is my /etc/asterisk/capi.conf I've tried to

Hi there, I searched in mailinglist and in web, but no answer to my problem... Only this post with no answers: http://lists.digium.com/pipermail/asterisk-users/2004-March/038994.html I'm using CVS Asterisk (05/17/04) with chan_capi 0.3.1. (multiple controller support). In my Asterisk-box there are 2 Fritzcards (module for second card compiled with changes on sourcecode found in the web).

Hi all, it took a while, but on sourceforge.net I added the new release 0.6 of chan_capi-cm driver. Note: dial string and capi.conf has changed. The main changes are: - added 'relaxdtmf'. - more BSD compatibility - correct PROGRESS handling - added verbose text for capi info/reason error messages. - use correct facility-selector for echo-cancel - added application capicommand() for CAPI