similar to: ZAP - Can't pickup calls on Analog Trunk

I am trying to turn up DID trunks with our local phone company but do not know the correct format of extensions.conf to do this.

Hi, Can I make e&m wink start lines just wait for digits - instead of going to default? Someone else cleared a similar problem (as described below) on an fxo port with "usecallerid => no" but it is not doing the trick for me. In this case the line when straight to default which would be ok also. John I posted the stuff below about a week ago... I set up a t1 from my sys75 to

Hi list, I've just compiled and installed Asterisk 1.4.16 and when I try to run "zap show" I get the message "*No such command 'zap show'*". I have a Sangoma Remora A400D with 2 FXS / 10 FXO ports, I've installed the latest wanpipe too. zaptel-1.4.7.1 was compiled from the wanpipe installation, so I don't know what's happening here!!! Any ideas???

Hi, all I have installed TDM400 with 1 FXS and 1 FXP ports. Now I am goig through documentation on how to configure it. It mentions 3 protocols: Loopstart, Groundstart and Koolstart. Which one do I use? Can someone send me sample zaptel.conf file for Australia? This will save me some time and will be used as a working example. Thanks, Rudolf

I installed asterisk on Fedora Core 2 kernel 2.6.5. I followed the standard procedure. zaptel-libpri-asterisk. The thing is that I constantly get the error message: line 4: Unable to open master device '/dev/zap/ctl' where the file zaptel.conf contains only 4 files: fxoks=1 fxsks=4 defaultzone=us loadzone=us I cant run asterisk and get a load of error messages. When I tried to check

I've been experimenting with the zaptel TDMoE stuff and I've got it all working. Calls go from one asterisk box to the other, with no issues, except they don't bring the callerID along with them. I tried the e&m signalling from the wiki and I thought maybe that had something to do with it, so I just changed it to half fxsks and fxoks and that didn't help me any, I still

Hi All; To overcome the echo problem, what mainly I have to do in the configuration other than the following line in the system.conf under dahdi directory? echocanceller=mg2,1-16 1) How can I know if the digium card supporting echo cancellator? 2) If I am getting a message in the consol that unable to enable the echo cancelator, then what does it means? The hardware is not supporting echo

I know this topic has been covered before - I just want to make sure I am understanding this correctly. | ------------------- | | | | T1 | Channel Bank | | ----------| | | | T1 Cross | | | | | | | | ------------------- -------------- | Asterisk | | | |

After speaking with several people, and even participating in a forum of several other people with echo issues, I thought I'd share what we've done (well actually what our chief R&D engineer, Brett Bourn has done...) First let me say that normal cheapy PC hardware couldn't be made to function with out echo. We tried on both the single port Digium T1 card and the 4 port Digium T1

I have a bit of a weird problem that I'm having great trouble debugging. I have a TDM400P PCI card with two FXO and two FXS modules. Both FXO modules are connected to BT lines here in the UK. Both BT lines have V23 Caller-ID, which works fine with Asterisk. Both asterisk and zaptel are fresh from CVS. Both FXO modules (channels 3 and 4) are in "group 1" for outgoing calls. My

As best i could figure it out, I've installed dahdi and rc4. My TDM400P doesn't answer fxo or fxs. /etc/dahdi/system.conf: loadzone = us defaultzone=us fxoks=1,2 fxsks=4 /etc/asterisk/chan_dahdi.conf: [house-phones] context=internal ; Uses the [internal] context in extensions.conf signalling=fxo_ks ; fxo_ks Use FXO signalling for an FXS chanel dahdichan => 1 ;

Hi again, I'm trying to setup our non pri T1 (they call it a Long Distance T1), our current pbx has the signaling set to E&M, I can set em in zapata.conf, but I'm trying to track down the proper entries for the zaptel.conf file. The digium docs only show a PRI example. Our current system has these settings: Signalling: E&M Framing mode: ESF Line Coding: B8SZ here's my

Two problems, possibly related: Here's the configuration...my Asterisk box has a TDM844B in it; port 1-4 are FXS, 5-8 FXOs. Here are the config files: /etc/zaptel.conf: -------- fxoks=1 fxoks=2 fxoks=3 fxoks=4 fxsks=5 fxsks=6 fxsks=7 fxsks=8 loadzone = us defaultzone = us -------- /etc/asterisk/zapata.conf: -------- [channels] language=en usecallerid=yes hidecallerid=no

We just bougth a tdm2400p with all the modules for FXO, but we are having some troubles with the card, cause it aparently is stripping some digits from the dialed number, we tested the same server with a tdm400 and everything worked as expected. We?ve already added "w" before the dialed number with no results, is there any way to solve, is it a bug thanks

Hi all, Does somebody know why no load modules to FXS? I used zaptel-1.0.7 version driver. [root@server1 zaptel-1.0.7]# modprobe wctdm ZT_CHANCONFIG failed on channel 3: Invalid argument (22) Did you forget that FXS interfaces are configured with FXO signalling and that FXO interfaces use FXS signalling? /lib/modules/2.4.21-27.EL/misc/wcfxs.o: post-install wcfxs failed

I am setting up 2 nufone lines. I want to make them both availiable for dial-out. How do you syntax it in extensions.conf so that it figures out which one is avaliable and dials out on it. Also how do you setup the name part of callerid for the outgoing lines?

Hello, everyone After having spent several time to look for any solution for my problem, I decided to write here. Here is the problem got a Digium X101 FXO card and Digium TDM400P alias freshmaker (1 fxs module on it on first port ) in my asterisk box. The X101 works perfectly. The problem comes from the TDM400, when i plug a tested working phone on it , i get no dialtone; the goal is to

I installed TDM400P and X100P pci cards in a system running mandrake 10.1 official, kernel 2.6.8.1-12mdksmp. I can compile zaptel, libpri, asterisk and modprobe (zaptel, wcfxs, wcfxo) without errors. Except that running ztcfg and asterisk fails. [root@asterisk asterisk]# ztcfg Notice: Configuration file is /etc/zaptel.conf line 3: Unable to open master device '/dev/zap/ctl'

My setup: X100P and Quicknet PhoneJack. I can't seem to properly set up a Zap channel for my X100P. Here are some of my configurations: [zaptel.conf] fxsks=1 #X100P fxoks=2 #Quicknet PhoneJack defaultzone=us loadzone=us [zapata.conf] [channels] context=local signalling=fxs_ks channel->1 ;X100P [extensions.conf] ... [local] exten=>_NXXNXXXXXX,1,Dial,Zap/1 ;I'm pretty sure the

I'm having (I think) timing issues in relation to bridged T1-T1 calls via dynamic spans. Fax calls are intermittently working, but voice is fine. My box has a Sangoma A400 inside it as the primary Zaptel timing source. My T1 PRIs that are hooked to the box come in via a foneBRIDGE2 (dynamic TDMoE spans). PRI #1 is the telco and PRI #2 is an existing Comdial FX-II. For some reason, bridged TDM