similar to: PRI and QSIG

I am looking to get the info about QSIG support in Asterisk. Does Asterisk have QSIG support? Does Asterisk support QSIG SIP Tunneling or QSIG SIP Interworking? If so, How to configure that? Thanks -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20060503/3cb7f966/attachment.htm

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hi, I'm attempting to hook up the E400P card to a Siemens ISDN module. I have no knowledge of these Siemens products, so I'm acting on what I've been told about it. The Siemens side is configured to "ISDN30: ECMA QSIG". The Siemens manual states the card provides 30 ISDN B-channels which can be used for trunking or

Hello, I have connected asterisk box with legacy PBX Alcatel OmniPCX 4400 (and also another * box connected to A4200). These PBXes have function to assign name to extensions and display it on phone. Asterisk box is connected via PRI with euroISDN signalling (also I have tried QSIG). Is it possible to set callerid with name and display it on alcatel digital phones? With command SetCALLERID

Hi all, I tried to connect the bristuffed(0.3.0-PRE-1i) * to an Alcatel PBX via BRI (zaphfc) and Q.SIG. The Alcatel PBX is connected to the outside world and should forward our calls to the telco. This setup works correctly as far as I use euroisdn as the switchtype. The first problem was that it is only possible to run the * side in CPE-mode -- I wanted NET. Anyway, I configured * this way:

I love it... I buy a half a million dollars worth of Trashiba's finest ... I download Asterisk for free... I now refer to it as legacy 18 months and 300 extensions later! Anyway, I am trying to integrate my dial plans acrossed platforms. PSTN>>>CTX670>>>Asterisk The dialplan I would like to setup, 1xx,2xx,3xx,7xxx to the CTX 670 4xx,6xxx to a remote ctx100 (this is setup

Hi, Is Asterisk "fully QSIG-compliant"? I currently have an Alcatel 4400 connected to Asterisk 1.2 and 1.4. Zaptel versions are 1.2.26 and 1.4.11. I am using switchtype=euroisdn and all works fine. However, it seems that Alcatel's latest firmware has dropped support for euroisdn which is really despicable. So now I need to see if I can migrate to QSIG which is supported by

Hello to all, I have a problem with an asterisk qsig. I have three machines: Nortel CS1000 --- Card Sangoma PRI ---> Asterisk QSIG ---SIP Trunk---> Asterisk I use Snom phones on Asterisk. If I call from Asterisk to Nortel, Nortel reminds me of the name of the person i'm calling and I visualize on the display of Snom phone, but if I call from Nortel to Asterisk, the QSIG does not send

[Reposting, as was bounced for non-member, sorry if this is a dupe] Arrangement: { PSTN }--E1--[PBX]--E1--[*]--LAN--[SIP phones] \__[PBX system phones] Normal calls between PBX system phones and SIP phones work, in both directions. The call logs look like (ignore the no answer, it did ring):

Guys, I need to make asterisk connect to another device over a pri using QSIG signalling (master/slave). Is this feasible and has it been done before? Thank you! al. _________________________________________________________________ Get ready for school! Find articles, homework help and more in the Back to School Guide! http://special.msn.com/network/04backtoschool.armx

I have read most of Eicons information on Q.SIG, and I am able to load the Q.SIG protocol (instead of ETSI for example). No strange logging in divacrtl mlog. But how do I tell Asterisk to understand Q.SIG? My PBX is configured for QSIG, but I cannot see anything on my trace when trying to make a call via the S0(Q.SIG) Janne > -----Ursprungligt meddelande----- > Fr?n:

That was my impression as well, I tried adding switchtype=qsig in zapata.conf, but all I see is the capi information... No connection... Janne > -----Ursprungligt meddelande----- > Fr?n: asterisk-users-bounces@lists.digium.com > [mailto:asterisk-users-bounces@lists.digium.com] F?r Peter Svensson > Skickat: den 23 februari 2005 21:34 > Till: Asterisk Users Mailing List -

Hi, we are still trying to properly connect a Tenovis PBX to an Asterisk server (asterisk 1.2.6, libpri 1.2.2, zaptel 1.2.5, Digium Wildcard TE110P), this time with QSIG. Calling from a Tenovis phone to a SIP phone (i.e. traditional phone -> Tenovis PBX -> QSIG -> Asterisk -> SIP phone) works with the following messages: --- Don't know what to do if second ROSE component is of

I have a PRI E1 link between Asterisk 1.4.24 and Alcatel-Lucent OmniPCX Enterprise R9.0. As EuroISDN it works fine. However, I need to move to QSIG because of a firmware upgrade on the Alcatel PBX which doesn't support EuroISDN (please don't ask why). Besides, I've read somewhere that 2 B Channel Transfers "should" work with * 1.4, the latest 1.4 libpri and QSIG. So this

Hello, Does anybody know if Asterisk can support QSIG protocols to be interconnected with a Traditionnal PABX? (Using a HFC chipset based ISDN card to emulate NT Interface) Thank you in advance ;-) Ignace

Hello all, as good? It would like to make a question, asterisk supports the protocol qsig, for interconnections in ISDN with equipment Siemens HiPath 4000 or same Ericsson MD110, so that it could identify to the name and the number of hosts and also to use some features of asterisk in the Siemens/Ericsson equipment. Greetings Josu? -------------- next part -------------- An HTML attachment was

Hello all, I need to conect an Asterisk with an Alcatel OmniPBX 4400 using an E1 port. It is the first time I make this kind of connection and I do not know exactly how to get it working. Someone has experience with this kind of connection? Could you paste a zapata.con and zaptel.conf files with QSIG configuration? Any clue will be wellcomed. Thanks Voipcrazy -------------- next part

Hello, I am using a Cisco-2,811 router with PRI as a gateway between Asterisk and Nortel TX-1. I had problems with name transfer and with the help of Cisco support I've fixed it. Enclosed here are the definitions needed for it. BTW, Cisco's CCM is using MGCP thus the Q.sig is handled by CCM. Here I am using SIP so the router must decode/encode the Q.sig. The Nortel should be defined

I have been asked by a potential customer whether we can connect an Asterisk box to an Ericsson MD110 that has an E1 port with ISDN-USR. They are unable or unwilling to upgrade their E1 port to QSIG. Has anyone here had experience of successfully making such a connection? I have found a couple of hits on Google that suggest it "should" work, but I'm after something a little more

I'm using a TE405p with all four spans enabled, two configured as pri_cpe and two as pri_net, the asterisk is sitting between our ISDN (UK BT EuroISDN30) and our phone system. We have 200 DDI numbers on the ISDN's and I need to give one of our clients dial-in access to be able to monitor calls we handle on their behalf. I've got ZapBarge working but I need to restrict the client

Hi everyone, I was referred to this mailing list by Richard Mudgett regarding the following thread on Issue Tracker as it's a feature request and not a bug:https://issues.asterisk.org/jira/browse/PRI-170 We've got a Nortel BCM (actually 2 BCM50s and 1 BCM400)... all showing the same problem. When a call comes in the number shows up OK but the name does not. In looking at the ISDN messages