similar to: Clicks, pops and noise

Hi again, I'm trying to setup our non pri T1 (they call it a Long Distance T1), our current pbx has the signaling set to E&M, I can set em in zapata.conf, but I'm trying to track down the proper entries for the zaptel.conf file. The digium docs only show a PRI example. Our current system has these settings: Signalling: E&M Framing mode: ESF Line Coding: B8SZ here's my

Im having a problem getting the 2 cards working together. I added the TDM with 3 FXO and 1 FXS board. The TE405p is working fine. THe TDM registers and identifies the FXO's and FXS but cant get them to go off hook. I hope someone can help. Asterisk seems to THINK its dialing it sends manager status as dialing, and it just sits there with no tones, on the phone dialing out. If I dial,

I just purchased a T100p from digium and a Carrier Access Access Bank 1 channel bank (12fxs/12fxo). I have the setup partially working thanks to some help from IRC. However I still have the following issues I can't seem to resolve 1. When calling into the system from the PSTN call hangup is not detected. * leaves line in use until it is shutdown. 2. When calling an analog phone connected to

After speaking with several people, and even participating in a forum of several other people with echo issues, I thought I'd share what we've done (well actually what our chief R&D engineer, Brett Bourn has done...) First let me say that normal cheapy PC hardware couldn't be made to function with out echo. We tried on both the single port Digium T1 card and the 4 port Digium T1

I'm having a problem with a new installation of asterisk 1.2.5 with a digium dual port T1 (span 1 connected to an outside line, and span 2 connected to a CAC access bank I channel bank with 24 fxs ports). When I start Asterisk (either from safe_asterisk or asterisk -vvvc) it will immediately exit after it initializes. It will start the logger, register applications and functions, register

Hi, Maybe someone has seen this before... I've installed a new T100P, but it doesn't seem to work. I've attached the T100P to an Adtran 750 using a crossover cable. The Adtran shows a red alarm on the T1 interface. The Adtran has been set to factory defaults with FXS cards in 1-3 and an FXO card in 5. The T100P shows no signs of life--the leds are not lit. Should I be seeing

I have a system that I am trying to get a port on a Sangoma A104d card connected to an Adtran 850 with 5 FXS modules and 1 FXO module. A problem I am having is figuring out what cable should be used from the port on the Sangoma to the JP2 port on the Adtran. Tried was a cross-over T1 (1->4, 2->5, 4->1, 5->2) as well as a straight T1 (1->1, 2->2, 4->4, 5->5). Neither one

We have install a DS3 with 28 DS1's we have an Adtran MUX breaking out the DS1's, we are trying to setup the system with 2 dchannels for each 4 DS1's. Everything looks fine when modprobe zaptel and wct4xxp and ztcfg -vvvvvv but when I asterisk asterisk it says: Aug 10 16:33:32 ERROR[8954]: chan_zap.c:6750 mkintf: Channel 24 is reserved for D-channel. Aug 10 16:33:32 ERROR[8954]:

I have just finished installing a new asterisk box at my work. The box is quite hefty, dual Zeon 2.8s with SCSI drives and 2Gb of memory. I have a 4 port Digium T1 card for channel bank and PRI access. I activated a PRI from a local CLEC (DMS-500 based, National protocol). This PRI is on slot 2 of the card and is set as the primary timing source. It is ESF/B8ZS. All the software is latest

I have a box with 12 T1s (4 Te410P cards). The PSTN provider is reporting slips and ask me to update the clock source. I have my system.conf set as the following but when I run dahdi_scan only the ports on Card 1 are showing up with syncsrc=1 system.conf : span=1,1,0,esf,b8zs bchan=2-24 mtp2=1 span=2,2,0,esf,b8zs bchan=26-48 mtp2=25 span=3,3,0,esf,b8zs bchan=49-72

We've been working for the past 2 weeks to get a new V400P working with our PRIs from the telephone company. We're trying to get the Asterisk server setup as a VoIP gateway for SIP and AIX. We can make SIP-SIP calls, but all calls from or to the PRI fail. This is the applicable entries from the Asterisk log (configuration files follow) for a call coming from the PSTN on the PRI. I

hi folks. i recently setup an Asterisk system in Hong Kong. their phone company told me that their T1 PRI switch type is Primary-NTT. however in chan_dahdi.conf there's no such option. i have it set to national. it worked fine for a while, but now suddenly stop working. in coming call just keep ringing and didn't even show up on console. out going call hang up immediately with cause code

In my * server I have a T100P, connected with a T1 crossover cable to an Adtran TA750 with 2 FXO cards. After I do 'modprobe wct1xxp;ztcfg' the alarm on the card starts blinking red. Running zttool confirmed that yes, it is a red alarm. I've read a few previous posts on this type of setup and I'm not too much closer. What should I be checking next? A different cable? The

Did you compile and install libpri *before* Asterisk? I had same problem (among others) b/c I didn't install in the correct order. Try the awesome asterisk_update.sh shell script. Are you trying to emulate CPE or NET? Try signalling=pri_cpe Check for whitespace behind the statement, zapata.conf seems bitchy about whitespace. hth -----Original Message----- From: Steve Totaro

Any ideas? 51] logger.c: [chan_zap.so] => (Zapata Telephony) Sep 28 00:42:35 VERBOSE[5151] logger.c: == Parsing '/etc/asterisk/zapata.conf': Sep 28 00:42:35 VERBOSE[5151] logger.c: == Parsing '/etc/asterisk/zapata.conf': Found Sep 28 00:42:35 VERBOSE[5151] logger.c: == Parsing '/etc/asterisk/zapata-auto.conf': Sep 28 00:42:35 VERBOSE[5151] logger.c: == Parsing

# Span 1 span=1,1,0,esf,b8zs bchan=1-23 dchan=24 echocanceller=mg2,1-23 # Span 2 span=2,2,0,esf,b8zs bchan=25-47 dchan=48 echocanceller=mg2,25-47 # Span 3 span=3,3,0,esf,b8zs bchan=49-71 dchan=72 echocanceller=mg2,49-71 # Span 4 span=4,4,0,esf,b8zs bchan=73-95 dchan=96 echocanceller=mg2,73-95 # Global loadzone = us defaultzone = us Span 1: TE2/0/1 "T2XXP (PCI) Card 0 Span 1"

List, I have a TE410P (T1 mode, all PRI) and a T100P (fxoks, for fxs channel bank). I cannot seem to get the T100P to send any clock to the channel bank. I prefer that it use the same clock source as the TE410P, but it doesn't matter if it's not in sync just as long as it's there. The TE410P is configured 3x pri_cpe, 1x pri_net. The three cpe go to XO Sonus switch, the net to

I have installed Asterisk on a CentOS4 box and then installed Asterisk from CVS. I installed a Sangoma A101 and connected it to a Adtran 600 using a T1 Crossover cable. The 600 has 12 x FXS, 12 x FXO interfaces. I ran through the wanpipe install instructions and configured it, now I can run [root@altpbx asterisk]# wanrouter hwprobe ------------------------------- | Wanpipe Hardware Probe Info

Hello. New to the list. We're in the process of deploying Asterisk. Actually, we're going live tomorrow, and I just found out that my Zaptel cards have been mis-configured. I'll preface this by saying that I have looked in the wiki, read through the samples, and attempted to call Digium (they're closed.) So I'm praying that someone on the list can help me out! I have two

Hello, I'm trying to set the 3rd span of a new digium quad card as a E&M T1 for Faxes to a Hylafax server. The 1st and 2nd spans are working as PRIs. When I start asterisk, the logs show a signaling error and chan_zap.c dies. I also get an error that it can't read the gains but they are the standard shown below. 2.6 kernel, Debian Stable, * 1.2 svn from feb 2007 my procedure: make