similar to: Is this normal?

Hi All, Hope you all are fine and good, Today i have found that Mine all PRI Channels are restating after every interval of one hour, and i have search and psot on fourms and everyone said that this is a normal behaviour. If this is a normal behaviour is there is any way to stop it { i still don't know what is the reson to restart ever hour } . Because this is listed everywhere that

Hi Guys, I have been checking logs and noticed this over the last night. Should I be concerned? and where to look for further details? Sample: [2010-04-13 04:31:27] VERBOSE[3844] logger.c: -- B-channel 0/1 successfully restarted on span 1 [2010-04-13 04:31:27] VERBOSE[3844] logger.c: -- B-channel 0/2 successfully restarted on span 1 [2010-04-13 04:31:27] VERBOSE[3844] logger.c: --

We are using AAH with Asterisk 1.2.7.1 with a TE405P as listed below. We are getting frequent restarts on the spans which lead to dropped calls. I have pasted some hopefully pertinent information below -- anyone have any clues that might help? Thanks Next line is repeated throughout messages, going through every channel in every connected span. asterisk/full.1:Apr 24 01:15:25 VERBOSE[4196]

Hi, Does anyone have any good empirical data suggesting what the maximum number of PRI calls (incoming and outgoing) without hardware echo cancellation can be handled on a single box is? I have a TE410P T1 (1st gen) card and I'm seeing interesting errors of D-Channels going down and then coming back up (See below). I've looked at the number of simultaneous calls at each of these points,

Does anyone know of a way to simulate the signaling of a PRI trunk for testing/setup purposes? I realize this may be a rather naive question, but I was wondering if you could take a TE110, for example, and using a crossover cable (or not?) and some means of emulating the NI2 signaling protocol connect it to another TE110 on another machine to test and verify an installation before the telco

Has anyone else had this symptom? It seems like my PRI ?restarts? each hour. I?ve got a PRI from Qwest in central California. What I don?t know is if this is on the * side or on the telco side. I don?t use my system enough to know if this is a big problem, a minor glitch or just an ?undocumented feature? - ? Any suggestions on how to track the source of these ?restarts?? Anybody else seen

Any ideas? 51] logger.c: [chan_zap.so] => (Zapata Telephony) Sep 28 00:42:35 VERBOSE[5151] logger.c: == Parsing '/etc/asterisk/zapata.conf': Sep 28 00:42:35 VERBOSE[5151] logger.c: == Parsing '/etc/asterisk/zapata.conf': Found Sep 28 00:42:35 VERBOSE[5151] logger.c: == Parsing '/etc/asterisk/zapata-auto.conf': Sep 28 00:42:35 VERBOSE[5151] logger.c: == Parsing

Did you compile and install libpri *before* Asterisk? I had same problem (among others) b/c I didn't install in the correct order. Try the awesome asterisk_update.sh shell script. Are you trying to emulate CPE or NET? Try signalling=pri_cpe Check for whitespace behind the statement, zapata.conf seems bitchy about whitespace. hth -----Original Message----- From: Steve Totaro

Is it normal for the following to occur hourly on an E1 PRI ? -- B-channel 0/1 successfully restarted on span 1 -- B-channel 0/2 successfully restarted on span 1 -- B-channel 0/3 successfully restarted on span 1 -- B-channel 0/4 successfully restarted on span 1 -- B-channel 0/5 successfully restarted on span 1 -- B-channel 0/6 successfully restarted on span 1 --

Hi all, I have a connect between a siemens hipath & Asterisk system over PRI The connection works perfectly I can call from the Hipath to an Asterisk Extension. I want to allow the hipath extensions to dial out over a SIP trunk on asterisk but I keep getting "The number you have dialed is not in service" In this CLI I'm dialing from hipath extension 9 (prefix for sip trunk)

[2009-05-27 02:06:16.294] WARNING[6971] chan_dahdi.c: No D-channels available! Using Primary channel 24 as D-channel anyway! [2009-05-27 02:06:16.295] VERBOSE[6971] logger.c: [2009-05-27 02:06:16.295] == Primary D-Channel on span 1 up [2009-05-27 02:06:16.301] ERROR[6971] chan_dahdi.c: !! Got a UA, but i'm in state 7 I noticed the above error many days after this at around 2AM. This

Hello, I'm running Asterisk@home 2.5 asterisk 1.2.4 zapatel 1.2.2 libpri 1.2.2 on a Dell Poweredge 2850 (1 CPU) with a TE210P I have 2 t1 circuits using NFAS with dchan on 24 and no backup dchan. I am able to receive inbound calls on all channels and can only make outbound calls on channels 25-48. Attempting to make an outbound call on channels 1-23 results in congestion.

I'm having a problem with a new installation of asterisk 1.2.5 with a digium dual port T1 (span 1 connected to an outside line, and span 2 connected to a CAC access bank I channel bank with 24 fxs ports). When I start Asterisk (either from safe_asterisk or asterisk -vvvc) it will immediately exit after it initializes. It will start the logger, register applications and functions, register

Hey everybody, I've, within the last 3 weeks, moved over to a PRI from SBC/AT&T. I've received several complaints about dropped calls. Reviewing the archives on PRI and dropped calls shows that I should set the resetinterval=never in the zapata.conf and restart. This hasn't helped. The dropped calls have to date only been on outbound calls. Usually within 2 to 3 minutes

Hi, I'm getting the following error from an asterisk 1.6.0.9 installation: [May 20 06:07:18] ERROR[18517]: chan_dahdi.c:10515 dahdi_pri_error: Asked to delete sched id -1??? [May 20 06:07:18] ERROR[18517]: chan_dahdi.c:10515 dahdi_pri_error: No more room in scheduler This repeats a few times, then asterisk crashes. I can't seem to locate any info on this error at all. I'm using

I have a server running Asterisk 1.4.14, Zaptel 1.4.6, Libpri-1.4.2 on a CentOS 5 server. The server has a single TE110 card connected to a provider called Alestra in Monterrey, Mexico. Since we installed everything we have been having problems dialing certain numbers, those numbers always fail when dialed from Asterisk but if you dial from your cell phone they always go through. I once has a

Hi all, I need to connect my Asterisk 1.4.26 with a Sangoma PRI card (configures with signalling=pri_net)) to a Cisco 2800 PBX. After connecting the cables everything seems fine (ifconfig w2g1 is ok, wanpipemonitor gives no errros, the span is up and active, green light on the card) but when I make a test with my iax phone, there's no way to dial the PBX and I get this WARNING: [Jul 2

Hi, I have debian etch 4.0 machine (2.6.18) with two TW-ISDN PCI (Hfc) cards. I use bristuff-0.3.0-PRE-1y-e (asterisk-1.2.17,libpri-1.2.4,zaptel-1.2.16). I also have patched zaphfc with zaphfc_0.4.0-test1_florz-13.diff.gz (I load module: insmod /usr/src/bristuff-0.3.0-PRE-1y-e/zaphfc/zaphfc.ko modes=1 debug=1). So i want to test two cards and make loop between them. So one card would be NT,

Hi, I set up a ring group. I would like for people who select a certain voice menu option to ring a list of extensions (I have just one extension in there at the moment) and if it doesn't answer to go to an extension's voice mail. I am using a version of asterisk from CVS, last updated a couple of weeks ago. This line in extensions_addtional.conf sends the call to ringgroup 3 if

I am in the process of implementing a new ISDN pri and have a couple of questions. This is a full 24 channels (23 B and 1 D) delivered over a T1 interface. The interface looks good and is not showing any errors. Any help that you can provide would be greatly appreciated. 1) What switchtype should be configured in the zapata.conf file when AT&T is using CUSTOM? My understanding is that