similar to: problems with remote access to PSTN

I have an X100P clone hocked up to an analog line of my PRI. I can use it to dial out. but when I call the extension it answers and says "GOODBY" I have a Livevoip DID which successfuly rings to ext 202 I am using asterisk@home and through the AMP inface the line should ring to ext 202 Below are Asterisk Messages, Extensions.conf and Extensions_additional.conf Extensions.conf

Hi, I have some problem to get this setup working. I have a CAC Channel Banl I, with FXO and an Asterisk box ( I am using Asterisk@Home 1.2) and I have a TE110p installed in this box. What I want to do is, just to be able to dial one of those lines that already are connected to the channel bank, and transfer that call through TE110p and Asterisk to a user agent somewhere through Internet.

Hello, I have *@Home 1.5 installed and all is working fine for incoming calls and sometimes outgoing calls. Installed in the box is a digium TDM04B (4xFXO Ports) setup as ZAP1 to ZAP4. I have incoming calls coming in on lines 1-4 in that order and outgoing calls prefering ZAP4 then ZAP3 then ZAP2. When i try to dial out to the PSTN from a SIP phone it sometimes works (normally after a reboot)

Hi all, I've recentrly starting to play around with *, when all I wanted is to configure an fritz ISDN card with A@H. Currently I'm stuck at the phase of what do I do with capi after everything is installed. I'm trying to understand how to setup incoming and outgoing calls at A@H since I'm getting a bit lost with the default dial plan. It seems that * answers but disconnect

Greetings *`s, I am manually creating call files and dropping them into /var/spool/asterisk/outgoing to be picked up by *. Presently, when I use local/internal parameters using SIP it works..ie I make an internal call from device to device. However, when I try dial an outside number which I have set up in a custom conf file, it bombs out with the following message :

Hi, I'm a newbie on * trying to setup an HFC card. I'm locked for many days getting the all-circuits-busy. And no idea what else to look for/how to diagnose. I'm in Spain, I've tried changing many parameters on zapata/zaptelcong with no luck, also NT & TE modes (honsetly, I've no idea what is). Any clue will be very much appreciated! I've installed *@home on my RH9,

Just installed V 0.4 of asterisk@home Programmed up 3 sip budgetone extensions, they call call each other fine. Tried to dial '9' for an outside line through an X100P to a packet8 ATA but got 'all circuits are busy now'. Here is the console output. == Spawn extension (from-internal, h, 1) exited non-zero on 'SIP/30-8d25' -- Executing

I'm having trouble getting outbound calls going with aah 1.3 and a tdm400p w/ 4 FXO. Incoming calls work fine, outbound I get this: -- Executing SetVar("SIP/231-af2b", "OUTNUM=6643955") in new stack -- Executing Cut("SIP/231-af2b", "custom=OUT_1|:|1") in new stack -- Executing GotoIf("SIP/231-af2b", "0?19") in new stack

Hello Guys, I'm somewhat of a newbie and am desperately seeking for some help... I've managed to get asterisk up and running on my server, and signed up with a broadvoice account... I'm having no problem dialing and communicating between extensions, but whenever anyone tries to call my broadvoice account, they are greeted by no ring or anything, but rather simply a direct to

On Wed, Mar 25, 2015 at 7:35 AM, Salaheddine Elharit <salah.elharit200 at gmail.com> wrote: > hello list, > > i have asterisk 11.15.0 and i have some trunks sip from my provider > > we have some ip phone astra 6731i > > each Ip-phone is configured with trunk and we call > > no ihave configured another trunk from the same provider in my asterisk > > i can call

hello list, i have asterisk 11.15.0 and i have some trunks sip from my provider we have some ip phone astra 6731i each Ip-phone is configured with trunk and we call no ihave configured another trunk from the same provider in my asterisk i can call all numbers just the numbers are configured in thses ip phones. but when i configured the same trunk in x-lite i can call theses ip-phones without

tnaks for your response but the number dialed exist and i can call this number when i configure the trunk directly in x-lite and i call call also this number from my cell phone . any help thanks and regards 2015-03-25 12:59 GMT+00:00 Matthew Jordan <mjordan at digium.com>: > On Wed, Mar 25, 2015 at 7:35 AM, Salaheddine Elharit > <salah.elharit200 at gmail.com> wrote: > >

Hi folks I seted up the asterisk with an active ISDN B1 AVM Card (german vendor) and it works fine, various SIP clients (IP fon snom, xlite under MacOSX) and also incoming and outgoing connectins. Ok. No problem. After that I configured a CP7940G with a MGCP IOS. It's connected to the asterisk too via switch. No NAT deivce between. And of course, I can call out to PSTN and also to one of the

I am making some assumptions, but assuming the 217.195.xx.xxx is your provider, you are getting this back from them: "Got SIP response 556 "No address found" back from 217.195.xx.xxx:5060" Are you sure that "0033149xxxxxx" is the format the provider is expecting? You might try enabling SIP debug on the 217.195.xx.xx IP and seeing what the INVITE looks like, but

Hi, I apologise if this is not the correct place to post such a message. I use Asterisk@Home package and all seems to be going well. I have identified one problem and have not managed to find anyway to fix(modify) it. We have a menu option that diverts to a mobile. If the mobile is off the network sends back a message to that effect. Now, this mobile does not have voicemail and asterisk is

thank you for your response below the asterisk -vvvr Using SIP RTP TOS bits 184 == Using SIP RTP CoS mark 5 -- Executing [0176XXXXXX at from-internal:1] Macro("SIP/300-00000192", "user-callerid,LIMIT,EXTERNAL,") in new stack -- Executing [s at macro-user-callerid:1] Set("SIP/300-00000192", "TOUCH_MONITOR=1427481319.470") in new stack --

thanks for your response i noticed that when i active the voicemail in the IP-phone where the number 0033149xxxxxx is configured i can call this number without issue the server asterisk and the ip-phone where the number is configured are in the same network 192.168.1.X Using SIP RTP TOS bits 184 == Using SIP RTP CoS mark 5 -- Called SIP/FD/0033149xxxxxx == Begin MixMonitor Recording

I see this: --8<---------------cut here---------------start------------->8--- > length(which(is.na(z$language))) [1] 0 > locals <- z[z$country == mycountry,] > length(which(is.na(locals$language))) [1] 229 --8<---------------cut here---------------end--------------->8--- where are those locals without the language coming from?! -- Sam Steingold (http://sds.podval.org/) on

I'm using samba 3.0.6 on fedora core 1 with LDAP enabled and smbldap-tools. When I change a user password with smbldap-passwd <username>, i find that sambaPwdMustChange attribute is correctly set to 30 days later as set in smbldap_conf. But, if I try to change password from any Win2000 or WinXP client with CTRL+ALT+CANC --> CHANGE PASSWORD i notice that sambaPwdMustChange attribute

Hello group I just update to the newest CVS now I'm not able to get asterisk to start. No error during the make or make install I did a make clean before the make;make install Any help would be great!!!! Here is the output asterisk -vvvvvgcd Parsing /etc/asterisk/asterisk.conf Parsing /etc/asterisk/extconfig.conf == Binding realtime_ext to mysql/realtime/extensions_table == Binding