similar to: HW Question (TDM400)

jglucky@blueware.net wrote: > Has anyone attempted or have had any issues getting Asterisk and > Digium cards working on a Dell SC420 server? I have it up and running on 2 SC420's with TE110P cards. Haven't had any problems as of yet (knock on wood). Dell SC420 TE110P 2x40 GB SATA drive in a RAID 1 setup (Linux 2.6 kernel needed for SATA drives; turn off RAID detection in BIOS).

Hi, all Here is a something I found on the web: http://www.voipbuster.com And it works OK too. Now, I want to use it via asterisk, so I ccan use my normal phones instead of PC application. Did anyone try to connect astersisk and VoipBuster? Thanks, Rudolf

Hi, all Where can I get "Asterisk Developer's PCI Kit" in Australia? It is a TDM400P with 1FXS and 1 FXO module. I amight need an extra FXS module as well. Thanks, Rudolf

Dear users: I have bought TDM04B card and it works in PCI 2.2 ver. slot. How can I check if specific mother board support PCI 2.2 ver. I do not have any documentation for that motherboard. B.

Hi folks, I'm stuck with a problem that I suspect has a trivial solution... I have a function, call it foo, that takes a number of arguments which it uses as parameters for a simulation. For later analysis, foo stores the names of the objects passed to it along with the simulation results in its output (written to a database). The objects names are accessed with deparse(substitute(argname)).

Skipped content of type multipart/alternative-------------- next part -------------- A non-text attachment was scrubbed... Name: not available Type: image/gif Size: 4325 bytes Desc: not available Url : http://lists.digium.com/pipermail/asterisk-users/attachments/20030403/f8281e8a/attachment.gif

I have a number of Polycom phones to setup with my * server. For my initial few phones I hand wrote configs. Does anyone here who uses Polycom phones have some form of management utility for automating their setup? Michael -- Michael Graves mgraves@pixelpower.com Sr. Product Specialist www.pixelpower.com Pixel Power Inc.

Hello, I have recently downloaded Sorcerer GNU Linux (http://sorcerer.wox.org/) which uses ISOLINUX for booting the installation CD-ROM. Problem is, I can not get the CD-ROM to boot. I have tested it on another computer, and it works fine (The CD-ROM has been written correctly). When I boot it on my home system, it gives me this error message: ISOLINUX 1.66 2002-01-01 isolinux: Disk error 00,

Hi all, We are in the process of selection IP Phones to work with our *new* Asterisk PBX. We want to buy 4 for something less than 1000$ but with a nice set of features to work with our mail box, lines, good sound quality, full duplex (and maybe speaker phone). Any suggestions for something with good voice quality and not much troubles to setup with Asterisk? Voici quality is the most

> Still trying to get NAT working. Try adding a canreinvite=no. Nabeel

Tested floppy boot on two machines (one PII 350, one 486DX4) Floppy boot with syslinux is very very slow, more than 18 mn to boot a linux kernel from floppy on the 2 machines. Tested with 3 different disquettes that were know to work, boot is reached after this very long time. Noise from floppy head make think floppy wait approximatly one minute between each read. No problem with pxe boot with

> Could you please try with a Debian kernel image There is one? I do not find it in either etch or sid (or on Alioth). Do I have to recompile a kernel?

Hello, I''m going to be helping a friend setup Shorewall in place of his Cisco router on his home network. Shorewall will be acting as the router/firewall gateway for internet access for his home LAN. His connection to the ISP is via PPPOE. Nothing unfamiliar here to me. It will be a standard 2 interface setup. My curiosity was peaked when he said that he is going to be installing

Hi, all I am doing "prrof of concept" system. I will have two IP phones connected to Asterisk box. Box itself will have 1 PSTN conenction and one analog phone conenction. A basic minimal configuration. At the moment I am planning to use an old PII-350 with 128M of RAM I have lying around. I can not test anything yet, as I am waiting for phones to arrive, so question is will that be

Does anyone have the physical spec sheet for the T100P from Digium? The one on the website doesn't have what I need. Things like 3.3 or 5v operation, uses n IRQ channels, requires 32-bit PCI, must be installed while standing on one foot and reciting the GPL, etc. Also, if anyone is selling a used T100P or TE4xxP I'd like to talk... Thanks, --Ernest

I sent a message a couple days ago about doing calculations for power of the ANOVA. Several people got back to me very quickly which I really appreciated. I'm working now on a similar problem, but instead of a balanced ANOVA, I have an unbalanced one. The first part of the question was: You assume that the within-population standard deviations all equal 9. You set the Type 1 error rate at á

Has anyone successfully run asterisk with a VIA processor ? I have tried unsucessfully, do I have to run make with any specific switches ?

John R Pierce wrote: > On 5/31/2017 10:13 AM, m.roth at 5-cent.us wrote: >> If I had realized it would run this long, I would have used DBAN.... For >> single drives, I do, and choose DoD 5220.22-M (seven passes), which is >> *way* overkill these days... but I sign my name to a certificate that >> gets stuck on the outside of the server, meaning I, personally, am

Hi, i am seeing an oops (every couple of days) on a UP PII system with SCSI disks, Kernel 2.2.19 and ext3 0.0.6b. All oops output passed the klogd thus i cant anymore pipe it through ksymoops - I ensured klogd got the correct System.map so the result should be reliable. Apr 25 17:03:10 Unable to handle kernel paging request at virtual address 8efd1fc8 current->tss.cr3 = 0981e000, %%cr3 =

Hi. I have 2 PC's connected with 1GBit NIC's. When I transfer a file from my File-Server(Redhat9.0, 256 SD-RAM, 300MHz PII, RTL8169 NIC, 2x Western Digital WD200JB RAID 0) to my Windows-PC(AMD Athlon XP 1800+, 1024 MB DDR-RAM, WINXP PRO, RTL8169 NIC, 2x Western Digital WD080JB RAID 0) with Samba, i get Speeds around 8-9MB/sec. I think this is too low for an GBit Network, so i tested the