similar to: sip log messages every few seconds

Asterisk 1.0.3 Sayson 480i running .78 release (problem may not be Sayson specific, it's just that's what's deployed) Problem: Asterisk rejects registrations every so often even though nothing has changed either with Sayson or Asterisk configuration (and previous registrations have succeeded) SIP trace of successful registration: =============================

I have an Avaya 4602 IP phone that was previously working with Asterisk. It was being used elsewhere for several months, and I recently set it up again to work with Asterisk. Everything works fine for several minutes -- I am able to receive and make calls as expected. However, after a few minutes, and every few minutes thereafter, I get the following message on the console: -- Got SIP

I am unable to get my 9133i to register with my asterisk server. I am including config files below, this a simple test network so there's nothing secret in the config files. I have upgraded the phone to the latest software version (1.4.3) I'm not sure what the problem is. I can call the phone from a softphone, but the 9133i says "no service" on the screen and I can't dial

Hi, I tried to cable #21 with a thomson cable modem mta: <-- SIP read from 192.168.153.100:5060: INVITE sip:%2321@195.38.96.5:5060 SIP/2.0 Via: SIP/2.0/UDP 192.168.153.100;branch=z9hG4bK1aa77a586 Max-Forwards: 70 Content-Length: 258 To: "#21" <sip:%2321@195.38.96.5:5060> From: sip:15800115@195.38.96.5:5060;tag=da42eb89613306c Call-ID:

Hi, I've just (earlier today) updated from CVS so that I can apply the dtmf caller id patches. Unfortunately this has had an undesired effect. I have an intertex ix66 which up until the CVS update allowed me to register my * server with the ix66 for my local domain (eg sip.mydomain.com). Now it appears that asterisk gets totally confused and tries to register with itself! Anyone got any

Hi, I have a terminal adaptor connected to Asterisk. I found that when it connect to Asterisk v1.0.0,The TA send register msg, and get OK msg, but it get Notify msg every 1 minute, The TA reply with "call does not exist" , usually 10 minutes later, The TA is down. But it work well with Asterisk v1.0-RC1, only register and OK msg are sent and got, no Notify msg is sent to it.

Currently I am having 2 issues with my Avaya 4602 phone: First, the phone registers with my Asterisk server, but when I start dialing I get a busy signal after 4 digits. I specified in the dialplan on the phone to expect 10 digits and that solved that problem, but I still immediately get a busy after the 10th digit. The phone never sends a dial command to asterisk. Second, asterisk is

Hi, I'm trying to get the match_auth_username=yes sip configuration working. It's mentioned as an experimental new feature of 1.6.2.x. (I'm using 1.6.2.8) The sip.conf example states: ; if available, match user entry using the ; 'username' field from the authentication line ; instead of the From: field. But still I've been unable to authenticate using username

Thanks a lot for your help so far. The main reason I do not use vms is that the server is pretty limited in RAM so this would only be my last resort. To prevent confusion: srv.wie (192.168.1.50) is the same machine as smb.wie (192.168.1.55), I seperated them just now to debug the problem. > These look like they are being run on the DC, what about from the > windows clients ? > I did

I am banging my head over a simple asterisk trick I was seeing on one asterisk server. An extension dials an international premium number, the called number answers, then the extension hangups, but the call continue to run on the international number side, generating an high profit for the premium number company and a big loss for the asterisk owner. I think some sort of "transfer"

Hello, Is it required to install an additional VNC server on XCP 1.1.0 dom0 box (ip 192.168.1.50)to get access to VNC-windows for installing domU guests? As I don''t use m$ / XenCenter so I need VNC for installation of new guests. The VM is running (s. below) *but* I was not able to open VNC window to continue the installation (s. error message further below) # --- uuid ( RO)

Hai, ? A bit off topic in the samba forum, but i thinks this is the best place to ask. ? Im having?some troubles to get the dhcp server fully working with samba4. I dont think this is a samba problem, but as i did say here maybe the best placy to ask.. ? It works, but not totaly. The strange thing is for example. ? My debian client is now working.? It adds and deletes as it should.? No

Before yesterday I had a perfectly (as far as I could tell) functioning PDC with samba, roaming profiles and all. Yesterday I made some changes to the server 1.) install dhcp3 server 2.) changed IPs from 192.168.1.50 to 192.168.1.1 3.) changed netbios name from garnet-base to garnetmain 4.) started two more interfaces eth1 (172.17.0.0/16) and eth2 (cable internet) eth0 is still 192.168.0.0/16

I am having two problems, possibly related, while performing pre-deployment testing of a Samba/OpenLDAP PDC with data that was vampired from an NT4 PDC. The Samba server fails to become a local master browser, and password change attempts (from a Windows client) fail. I followed Samba-Guide/ntmigration.html (taking some liberties with various items of configuration), ending with step #19.

Don't know how that last email took off, but that wasn't suppose to happen. Any the root 3 59.6 0.0 0 0 ? R< 10:16 11:04 [events/0] is a kernel thread that handles weird irq stuff. I just disabled onboard sound and USB and it went away. I'm still left with my other problems though, here they are 2.) I'm having LMB and DMB problems on the server,

I''m trying to use the traffic control features of Shorewall. I share my network with some guys, and I have a tcclasses file like this: #Hunter Fuller eth0 100 1500kbit full 50 tos-maximize-throughput #(other guy''s name) eth0 110 1500kbit full 50 tos-minimize-delay etc., based on their personal preferences. Then

> > This sounds like a dns problem, are your windows machines using the DC > as their nameserver ? > yes they are using the server as dns. DNS is done through bind9 and implemented in samba via bind9_dlz. All looks fine: $ host -t A smb.wie smb.wie has address 192.168.1.50 $ host -t SRV _kerberos._udp.smb.wie _kerberos._udp.smb.wie has SRV record 0 100 88 srv.smb.wie. $ host -t SRV

Hi All, I have set up a box that will be used as follows: SIP Phone ----> Asterisk ----> Cisco H323 VoIP Server 192.168.1.5 192.168.1.50 192.168.1.80 Asterisk is running the latest CVS and oh323 driver. The SIP phone is a Grandstream Budgetone 100. I have everything setup and running with G.711 ALAW and ULAW and i'm able to make calls through

Hi Samba folks! I have a problem concerning RPC calls. In a domain environment running 3.0.3pre2 I have no problems shutting down remote computers. I now have a small environment with only 2 computers in a workgroup. My samba server is running on a FreeBSD 5.4 box and my client is a Win XP Pro SP2 box. When I try to use net rpc shutdown -I 192.168.1.50 -U Administrator i get the

Hi, I've tried to use SIPSAK to understand the troubles i'm having about sending my voice to the person I've called (extension), after doing this tests below I always got this error "error: this FQDN or IP is not valid: voicegw". This could cause problems (namely audio problems)? Best regards, Helder voicegw:~# sipsak -C empty -a password -s