similar to: Fax trouble with HP 3330mfp (again)

Hi list! I'm trying to get PrivacyManager working but for some reason it always thinks that CallerID is present (when it isn't). I get this on the console: == Primary D-Channel on span 1 up -- Accepting voice call from '' to '0711234567' on channel 0/2, span 1 -- Executing Ringing("Zap/2-1", "") in new stack -- Executing

Hi, I have a couple of questions about Quad-BRI solutions for Asterisk, and was hoping that I might get some feedback based on other people's experience. We currently use the Junghanns card, which is a pure Zaptel solution, which is fantastic, but they have no hardware EC solution, and their drivers are becoming increasingly un-stable with time (I back-port to a modified qozap driver from

Hi list! On a newly installed RHEL 4 box I'm trying to install bristuff-0.2.0-RC8n. Everything did compile but I am running into some problems with the zaphfc driver. First of all when I load zaphfc *before* zaptel (yes I know I shouldn't do that) I get a kernel panic and the box hangs. Not so nice, especially when you are trying to fix stuff from remote locations. But ok. Now for

I tried to get callerid working the normal way but the cid is never passed to the phone. It doesn't work untill I set SetCIDNum(0${PRI_NETWORK_CID}) in extensions.conf which I found in the wiki: http://www.voip-info.org/tiki-print.php?page=Asterisk+zaphfc Is this intended behaviour, or still a bug? It does work but it only shows one zero even though I have nationalprefix = 0

Hi list! I am running CentOS 4.1 x86_64 on an Athlon64. The box was installed only yesterday. Yesterday I was still able to compil stuff, yesterday even the tiniest and simplest programs fail to compile always with internal compiler error: Segmentation fault. For example: make -C /usr/src/linux-2.6 SUBDIRS=/tmp/bristuff-0.2.0-RC8n/qozap ZAP=-I/tmp/bristuff-0.2.0-RC8n/zaptel-1.0.9 modules

Hi! Still trying to get fax to work in a reliable manner. I have some dumb fax machines that do not have a setting to limit tx/rx speeds. For some reason when training they often think the line is good enough for 14k4 or higher after which the fax will fail. Is there any other way of forcing the faxes to lower their speeds? Would it be possible to monitor certain extensions for the sound

BUG/SYMPTOMS: 1.Under certain circumstances, octoBRI (and most likely quadBRI) ISDN cards (Junghanns/CologneChip) severely distort certain ISDN payload. 2.Although these claims relate to the bristuff patch, the problem might not be limited to bristuff and in fact be rather asterisk/zaptel/libpri related. 3.Signal distortion is limited to the use of the CVS version of the Bristuff patch for

Hi, I am just moving from Asterisk 1.2+bristuff up to 1.6.2, a huge leap :) I was wondering if someone could point me at 3 things that I appear to have "lost"? 1) ZapEC(off) - Is there an equivalent dialplan command to request no EC on a channel before dialling in DAHDI? 2) rxfax(file.tiff) - I have found ReceiveFax(), but I am aware that much has happened in the faxing stakes

Hi all, I'm installing two HFC pci card (both in TE mode), I don't have problem when load module, but whrn I give "ztcfg -vv", I see 6 the six channels that I configured, then my computer hang and I have to reboot it. (I'm using a VIA Epia-M 1000 with Via C3 processor) root@test:~# modprobe zaptel root@test:~# insmod /usr/src/bristuff-0.2.0-RC8n/zaphfc/./zaphfc.o

Hi Guys I have been running a test server for a few days now with * 1.0.9 bristuff RC8n. I had a power failure and the test machine was not on the ups. When power was restored I found the following error: FATAL: Error inserting zaphfc (/lib/modules/2.6.11.4-20a-default/misc/zaphfc.ko): Unknown symbol in module, or unknown parameter (see dmesg) My dmesg output: zaphfc: unsupported

hi all! I'm running an Asterisk-box with bristuff-....RC8n and 2 HFC-S cards. I m located in Vienna/Austria. I have the problem that on outgoing calls i hear my voice as a short echo (about half a second). This occurs not on every call. I tried some changes in my zapata.conf, with rxgain and txgain settings, but to me its hard to find a configuration which is good for every call i make. Is

hello, I have a asterisk box (Slackware 9.1.0, Linux 2.4.31) connected to a Ericsson Businessphone PBX on the internal S0 bus with HFC-S card and zaphfc driver - point2point mode -. --------- | TELCO | | BRI | --------- | | PBX external S0 -------- | PBX | -------- | PBX internal P2P S0 NT Mode | | HFC-S Card P2P TE Mode

-----Ursprungligt meddelande----- Fr?n: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com] F?r Terry Wade Skickat: den 19 augusti 2005 07:08 Till: 'Asterisk Users Mailing List - Non-Commercial Discussion' ?mne: RE: [Asterisk-Users] Zaphfc.ko module error Hi Remco Thanks for the response. I am running Suse 9.3 kernel 2.6.11.4-20a-default. Will check

hi all, I have this anoying problem with Direct in Dial, when someone calls from an extern analog phone to my isdn number, Asterisk is not waiting for the DID numbers the caller dials after the main-number. Version: Asterisk 1.0.9-BRIstuffed-0.2.0-RC8n, with junghanns quadbri zapata.conf: switchtype = euroisdn signalling = bri_cpe faxdetect=incoming pridialplan = unknown prilocaldialplan =

Trying to compile BRIstuff 0.2.0-RC8o. Ran the download.sh and compile.sh scripts to automate the process. gcc -pipe -Wall -Wstrict-prototypes -Wmissing-prototypes -Wmissing-declarations -g -Iinclude -I../include -D_REENTRANT -D_GNU_SOURCE -O6 -march=i686 -DZAPTEL_OPTIMIZATIONS -DASTERISK_VERSION=\"1.0.9-BRIstuffed-0.2.0-RC8n\" -DINSTALL_PREFIX=\"\"

Hi, For a significant time now (since about 0.2.0-rc8n) the qozap driver has become very verbose if an ISDN line is not connected... I get the messages below every couple of seconds in the asterisk logs. The "flaw" in the messages is the "Alarm cleared" message - The alarm cannot possibly be cleared because there is no physical media connected into that port!!! (BTW - All

I have a problem with Asterisk-bristuffed using a zaphfc card. I am located in the Netherlands, so I have an ISDN line from KPN. When I start Asterisk, and plug in the ISDN line, everything works perfectly for about 5 minutes. And then the ISDN line is down for 1 minute, and after that minute, the line comes back up and works for another 5 minutes. Every time the line goes down I get the error

Hi all, I replaced a TE410P Rev C 1st Generation Firmware with a TE411P without any cfg changes (zaptel/zapata). As a result Asterisk crashes on outbound from PRI4 going to PRI1 calls: Aug 23 18:22:00 WARNING[4693]: chan_zap.c:7545 zt_pri_error: PRI: !! Got a UA, but i'm in state 1 Aug 23 18:22:00 WARNING[4693]: chan_zap.c:7545 zt_pri_error: PRI: !! Got a UA, but i'm in state 1

I have a serious problem that repeats very often, after 30 - 50 calls and I can only solve it by stopped and restarting * :-( After a while, * seems to loose track of something. When an ISDN call from PBX needs to go to the Telco, I get 'Ring requested on unconfigured channel 255/255 span 2' It's always channel 255/255 ??, the 'span' number is random Setup: * between Local

Hi, I can't receive/send calls with Asterisk. Could someone please give me a few pointers on my configuration? Regards, Norman Zhang ; sip.conf [general] disallow=all allow=ulaw port=5060 bindaddr=0.0.0.0 externip=x.x.x.x localnet=192.168.22.0 mask=255.255.255.0 context=inbound-sip maxexpirey=180 defaultexpirey=160 tos=reliability srvlookup=yes register =>