similar to: [Asterisk-Dev] Severe ISDN signal distortion in CVS-HEAD with octoBRI

Hi, Using Xorcom's bristuff-0.4.0-RC4-xr7.tar.gz (ie asterisk 1.4.25) with an old Junghanns OctoBRI (ie not the 2.0 version), zttool shows every port in TE mode, though half of them are in NT. Alarm column shows OK for every port, such as : OK octoBRI PCI ISDN Card 1 Span 1 [TE] Lay Globally, this system doesn't work (can't dial out through zaptel) Replacing this board

Hi list! On a newly installed RHEL 4 box I'm trying to install bristuff-0.2.0-RC8n. Everything did compile but I am running into some problems with the zaphfc driver. First of all when I load zaphfc *before* zaptel (yes I know I shouldn't do that) I get a kernel panic and the box hangs. Not so nice, especially when you are trying to fix stuff from remote locations. But ok. Now for

Hi all, I just posted this question before last week. Meanwhile after upgrading Asterisk 1.0.7-BRIstuffed-0.2.0-RCg to 1.0.8-BRIstuffed-0.2.0-RCh the same problem occurs, but seems to be more seldom. Attached is now the output of "zap show channel" . - I'm running a stable Asterisk on a HP DL380G2 1.4Ghz 0,5GB RAM equipped with 1x TE410P and 2xJunghanns OctoBRI running in NT-mode.

Hi list! I am running CentOS 4.1 x86_64 on an Athlon64. The box was installed only yesterday. Yesterday I was still able to compil stuff, yesterday even the tiniest and simplest programs fail to compile always with internal compiler error: Segmentation fault. For example: make -C /usr/src/linux-2.6 SUBDIRS=/tmp/bristuff-0.2.0-RC8n/qozap ZAP=-I/tmp/bristuff-0.2.0-RC8n/zaptel-1.0.9 modules

Hi, I mistakenly posted this to Dev list.... I wonder if I use quadbri or octobri cards to insert Asterisk between ISDN PBX and ISDN line - if power of Asterisks fails - will those card connect PBX directly to ISDN line ? If not are there any other simple switching devices, that would do this (in power fail it will connect ISDN PBX to ISDN lines directly) ? Thanks in advance, regards, Rob.

Hi all, I have made (S)RPMS of cvs STABLE & HEAD and several other apps and put them online at http://www.laimbock.com/asterisk/ The cvs STABLE RPMS support udev, Eicon Diva Server cards, HFC-S based ISDN cards, QuadBRI and OctoBRI ISDN cards from Junghanns.net and SpanDSP for sending & receiving faxes. The sample files are also included and are put in

Hello all, This email is intended rather informative than questioning. While developing some script-generated dial plan, we figured out that there are differences between Snom 190's and BudgeTone 101's relating to transfers. It appeared that the 190's will have their own 'Caller ID' set as the 'CALLERID' variable in astersisk when transfering a call, while the

Hello, In my system, dmesg outputs : [ 13.039788] wcb4xxp 0000:01:0a.0: probe called for b4xx... [ 13.039788] ACPI: PCI Interrupt 0000:01:0a.0[A] -> GSI 21 (level, low) -> IRQ 21 [ 13.039788] wcb4xxp 0000:01:0a.0: Identified HFC-8S Junghanns.NET octoBRI PCI (controller rev 1) at 0001dfe0, IRQ 21 [ 13.041202] wcb4xxp 0000:01:0a.0: NOTE: hardware echo cancellation has been disabled [

Hello, I recently bought a Junghanns Octobri Card. I have some problems with this card to make outbound calls but I can receive calls. I have 3 lines to PSTN and 3 lines to my existing PBX FRANCE TELECOM <-- OctoBRI --> Asterisk 1.2.4-BRIstuffed-0.3.0-PRE-1h <-- OctoBRI --> PABX e-Generis <----> ISDN Phones |

Hi, I'm pulling my hair down and getting bold :-) ..... I have Asterisk between Panasonic KXTD816 and Euroisdn in Italy (beronet octobri and bristuff Asterisk).... I'm trying to do just plain transfer of call from pbx to ISDN through Asterisk... It seems like PBX hangsup, when call is progressing with no apparent reason. I'd kindly ask for any advice or some working example for

Hi, When typing dahdi_scan on an OctoBRI-enabled setup, I've got only 8 replies such as : [1] active=yes alarms=RED ... [8] active=yes ... framing=CCS I would expect 16 replies (one per B-channel). Is this correct ? Regards -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hi all, I'm installing two HFC pci card (both in TE mode), I don't have problem when load module, but whrn I give "ztcfg -vv", I see 6 the six channels that I configured, then my computer hang and I have to reboot it. (I'm using a VIA Epia-M 1000 with Via C3 processor) root@test:~# modprobe zaptel root@test:~# insmod /usr/src/bristuff-0.2.0-RC8n/zaphfc/./zaphfc.o

I'm using Asterisk 1.09 with bristuff 0.2.0-RC8n, one BRI line and a Sipura SPA-2000. I have a HP LaserJet 3330mfp all-in-one. I can receive faxes but not send them. The faxes start whistling to each other but the transmission is stopped with a "communication error" To receive a fax I have this in my dialplan: exten => 0000000000,1,Ringing exten => 0000000000,2,zapEC(off)

hello, I have a asterisk box (Slackware 9.1.0, Linux 2.4.31) connected to a Ericsson Businessphone PBX on the internal S0 bus with HFC-S card and zaphfc driver - point2point mode -. --------- | TELCO | | BRI | --------- | | PBX external S0 -------- | PBX | -------- | PBX internal P2P S0 NT Mode | | HFC-S Card P2P TE Mode

Hi, we've purchased new Beronet Octobri card and have problems loading modules for stock Asterisk for Debian Sarge (it has bristuff patches in it). when loading qozap it says that no multibri card was found although lspci shows it... There were quite some rumours about bristuff not liking other than junghanns cards, but don't know if something happened.... Anyone recently used this

Hi Guys I have been running a test server for a few days now with * 1.0.9 bristuff RC8n. I had a power failure and the test machine was not on the ups. When power was restored I found the following error: FATAL: Error inserting zaphfc (/lib/modules/2.6.11.4-20a-default/misc/zaphfc.ko): Unknown symbol in module, or unknown parameter (see dmesg) My dmesg output: zaphfc: unsupported

Trying to compile BRIstuff 0.2.0-RC8o. Ran the download.sh and compile.sh scripts to automate the process. gcc -pipe -Wall -Wstrict-prototypes -Wmissing-prototypes -Wmissing-declarations -g -Iinclude -I../include -D_REENTRANT -D_GNU_SOURCE -O6 -march=i686 -DZAPTEL_OPTIMIZATIONS -DASTERISK_VERSION=\"1.0.9-BRIstuffed-0.2.0-RC8n\" -DINSTALL_PREFIX=\"\"

Hi all, I routinesly rips my CDs to WAV and then convert to ogg vorbis format for use in my car and portable player. I don't usually notice anything amiss, but on the last track of Mike Oldfield's "Music of the Spheres" album ("Musica Universalis", at the very end crescendo), the converted .ogg file exhibits terrible distortion (sounds like digital clipping). This

hi all! I'm running an Asterisk-box with bristuff-....RC8n and 2 HFC-S cards. I m located in Vienna/Austria. I have the problem that on outgoing calls i hear my voice as a short echo (about half a second). This occurs not on every call. I tried some changes in my zapata.conf, with rxgain and txgain settings, but to me its hard to find a configuration which is good for every call i make. Is

Hi, I'm trying to connect quadbri between powered ISDN phone and ISDN line: ISDN <---1---> TE - * - NT <--2--> Phone I use quadbri, suse 9.2 and latest 0.2.0-RC7k bristuff. I've used sample settings provided with package, but do get strange error (I think that I have wrong setting for P2P or P2MP setting and cables 1 and 2). If I connect phone to ISDN with straight cable