similar to: SV: Zaphfc.ko module error

Hi Guys I have been running a test server for a few days now with * 1.0.9 bristuff RC8n. I had a power failure and the test machine was not on the ups. When power was restored I found the following error: FATAL: Error inserting zaphfc (/lib/modules/2.6.11.4-20a-default/misc/zaphfc.ko): Unknown symbol in module, or unknown parameter (see dmesg) My dmesg output: zaphfc: unsupported

Hi list! On a newly installed RHEL 4 box I'm trying to install bristuff-0.2.0-RC8n. Everything did compile but I am running into some problems with the zaphfc driver. First of all when I load zaphfc *before* zaptel (yes I know I shouldn't do that) I get a kernel panic and the box hangs. Not so nice, especially when you are trying to fix stuff from remote locations. But ok. Now for

hello, I have a asterisk box (Slackware 9.1.0, Linux 2.4.31) connected to a Ericsson Businessphone PBX on the internal S0 bus with HFC-S card and zaphfc driver - point2point mode -. --------- | TELCO | | BRI | --------- | | PBX external S0 -------- | PBX | -------- | PBX internal P2P S0 NT Mode | | HFC-S Card P2P TE Mode

Hi, my zaphfc is flooding my syslog with two messages (even without asterisk running). Is this "normal"?: -------------------------------------------------- zaphfc: bchan rx fifo not enough bytes to receive! (z1=1360, z2=1353, wanted 8 got 7), probably a buffer overrun. zaphfc: dropped audio (z1=2712, z2=2695, wanted 8 got 17, dropped 9). With Asterisk running (asterisk -vvvvvgc)

I would like to know how to install asterisk 1.0.9 with zaphfc working on a SuSE 9.2. I tried this: - The rpms with SuSE 9.2 are asterisk 1.0.6 - bristuff works, except for zaphfc, which doesn't compile. - The official asterisk download file doesn't contain isdn bri support Any ideas? Lars Dybdahl.

Hi all, I'm installing two HFC pci card (both in TE mode), I don't have problem when load module, but whrn I give "ztcfg -vv", I see 6 the six channels that I configured, then my computer hang and I have to reboot it. (I'm using a VIA Epia-M 1000 with Via C3 processor) root@test:~# modprobe zaptel root@test:~# insmod /usr/src/bristuff-0.2.0-RC8n/zaphfc/./zaphfc.o

Hi list! I am running CentOS 4.1 x86_64 on an Athlon64. The box was installed only yesterday. Yesterday I was still able to compil stuff, yesterday even the tiniest and simplest programs fail to compile always with internal compiler error: Segmentation fault. For example: make -C /usr/src/linux-2.6 SUBDIRS=/tmp/bristuff-0.2.0-RC8n/qozap ZAP=-I/tmp/bristuff-0.2.0-RC8n/zaptel-1.0.9 modules

I have a problem with Asterisk-bristuffed using a zaphfc card. I am located in the Netherlands, so I have an ISDN line from KPN. When I start Asterisk, and plug in the ISDN line, everything works perfectly for about 5 minutes. And then the ISDN line is down for 1 minute, and after that minute, the line comes back up and works for another 5 minutes. Every time the line goes down I get the error

Hi Running slackware 9.1 with compiled kernel patched to 2.6.6 running ok. Having problems compiling zaphfc.c First thing was the can't find "irq_vectors.h", but "solved" by changing the #include "irq_vectors.h" to #include "mach-default/irq_vectors.h" in /usr/src/linux/include/asm/ directory. But I still have errors with "structure has no

Caller id is not in the configs that are supplied with zaphfc from bristuff, and it's not mentioned in the wiki. Is it possible to use callerid with zaphfc/bristuff? Thanks!!

How i can log to understand where is my problem Sometimes zaphfc hang my nt1 plus with that error zaphfc: empty HDLC frame received. zaphfc: dchan tx fifo total number of frames exceeded! zaphfc: dchan tx fifo total number of frames exceeded! zaphfc: dchan tx fifo total number of frames exceeded! zaphfc: dchan tx fifo total number of frames exceeded! zaphfc: dchan tx fifo total number of frames

Hi, I solved the Problem: the context defined in zaptel.conf: context = zapincoming was not in extensions.conf, so nothing worked. ( I assumend this context is only necessary for calls from zaptel, not to it) This may be a bug: in the verbose log I found nothing like "[chan_zap] Could not initialize ..., due to ....", this had helped alot and had saved alot of hours (-;

Hello, I've added a ZAPHFC card to my CAPI based system. Calls coming in via ZAPHFC do not forward the caller id to the SIP phones. Calls coming in via CAPI do forward the caller id to the SIP phones. Any and all help is greatly appreciated. The (hopefully relevant) conf file excerpts are: extensions.conf =============== exten => 807440,1,Answer exten => 807440,2,Noop exten =>

Hello, After searching the archives, I''ve found only two messages regarding this case, but there were no solution. I have a similar problem, so I try to ask here. I have twi HFC chipset ISDN cards in my pc: 0000:00:0d.0 Network controller: Cologne Chip Designs GmbH ISDN network controller [HFC-PCI] (rev 02) Subsystem: Cologne Chip Designs GmbH ISDN Board Flags: bus

<!DOCTYPE html PUBLIC "-//W3C//DTD HTML 4.01 Transitional//EN"> <html> <head> <meta content="text/html;charset=ISO-8859-1" http-equiv="Content-Type"> <title></title> </head> <body bgcolor="#ffffff" text="#000000"> Hi,<br> <br> I am trying to get zaphfc running in nt mode with asterisk.

I have some problems starting asterisk with a hfc card using zaphfc: [chan_zap.so]Mar 8 17:53:06 WARNING[2447]: loader.c:258 ast_load_resource: /usr/lib/asterisk/modules/chan_zap.so: undefined symbol: ast_retrieve_call_to_death Mar 8 17:53:06 WARNING[2447]: loader.c:391 load_modules: Loading module chan_zap.so failed! I'm using asterisk from debian/sid: Asterisk

Hi, We've been using zaphfc single ISDN cards as cheap Zaptel timing sources for our Asterisk boxes for a long time, and in the asterisk 1.0.x series, had zero problems doing so. I now have some boxes with Zaptel 1.2.x (with a mixture of 1.0.x asterisk and 1.2.x asterisk), and this setup no-longer seems stable - By plugging or unplugging the ISDN cable, and sometimes just randomly the card

Hi, I'm tring to setup a ISDN HFC card in NT mode, but I have a problem with ztcfg that always report a problem regarding FXS/FXO signaling. Is someone have ever seen this ? Loadind the zaphfc module seems ok.... -- insmod ./zaphfc.o modes=1 ------------ zaphfc: card configured at mem 0xc89eee00 fifo 0xc29e8000(0x29e8000) IRQ 19 HZ 100 zaphfc: Card 0 configured for NT mode zaphfc: 1 hfc-pci

Hi, I'm banging my head on compiling bristuff modules for Suse 10.0 with kernel : Linux laps1 2.6.13-15.7-smp #1 SMP Tue Nov 29 14:32:29 UTC 2005 x86_64 x86_64 x86_64 GNU/Linux and Asterisk 1.2.1-BRIstuffed-0.3.0-PRE-1f . I get this : laps1:~/Voipy/1.2.1/bristuff-0.3.0-PRE-1f/zaphfc # make load make -C /usr/src/linux-2.6 SUBDIRS=/root/Voipy/1.2.1/bristuff-0.3.0-PRE-1f/zaphfc

Hello all, I've a little clue with zaphfc used to connect to a BRI linethat probably can be a configuration issue.... (really I hope so) Here, telcos (expecially mobile operators) use to substitute the dialtone with some vocal indication without answer the line. (Indications like "The customer is not reachable" or "wait because the customer is on the phone" ecc..) For